Approaching Self-Bonded Medium Density Fiberboards Made by Mixing Steam Exploded Arundo donax L. and Wood Fibers: A Comparison with pMDI-Bonded Fiberboards on the Primary Properties of the Boards.

This study presents an unexplored method to produce formaldehyde-free MDF. Steam exploded Arundo donax L. (STEX-AD) and untreated wood fibers (WF) were mixed at different mixing rates (0/100, 50/50, and 100/0, respectively) and two series of boards were manufactured, with 4 wt% of pMDI, based on dry fibers, and self-bonded. The mechanical and physical performance of the boards was analyzed as a function of the adhesive content and the density. The mechanical performance and dimensional stability were determined by following European standards. The material formulation and the density of the boards had a significant effect on both mechanical and physical properties. The boards made solely of STEX-AD were comparable to those made with pMDI, while the panels made of WF without adhesive were those that performed the worst. The STEX-AD showed the ability to reduce the TS for both pMDI-bonded and self-bonded boards, although leading to a high WA and a higher short-term absorption for the latter. The results presented show the feasibility of using STEX-AD in the manufacturing of self-bonded MDF and the improvement of dimensional stability. Nonetheless, further studies are needed especially to address the enhancement of the internal bond (IB).

Seagrass Leaves: An Alternative Resource for the Production of Insulation Materials.

Seagrass wracks, the remains of dead leaves accumulated on seashores, are important ecosystems and beneficial for the marine environment. Their presence on the touristic beaches, however, is a problem for the tourism industry due to the lack of aesthetics and safety reasons. At the present time, seagrass leaves are landfilled, although this is not considered an ecological waste management practice. Among other proposed practices for more sustainable and environmentally friendly management, such as composting and biogas or energy generation, in this study we aim to use seagrass leaves for the production of insulation materials. Insulation boards from two types of seagrass leaves (Posidonia oceanica and Zostera marina) at densities varying from 80 to 200 kg m-3 were prepared and their physical and mechanical properties were examined and compared to those of wood fiber insulation boards. The thermal conductivity of seagrass-based insulation boards varied from 0.042 to 0.050 W m-1 K-1, which was up to 12% lower compared to the latter. The cone calorimetry analysis revealed that seagrass-based insulation boards are more fire resistant than those from wood fibers, as they release very low amounts of heat during combustion and do not ignite when exposed to a single flame (Bunsen burner). A simplified cost analysis showed that insulation boards made from seagrass leaves can be up to 30% cheaper compared to those made from wood fibers. After their end of life, seagrass leaves can again be considered a valuable resource and be further utilized by adopting other management strategies.

Loofah Sandwich Panels: The Effect of Adhesive Content on Mechanical and Physical Properties.

In the development of new materials, the focus nowadays is increasingly on their relevance with regard to lightweight construction or environmental compatibility. The idea of a lightweight sandwich panel was inspired by an increasing number of cosmetic accessories that use the fibers of the loofah plant, a rapidly renewable, light, fibrous raw material. The aim of the study was to develop a fiber composite panel based on the fibers of the loofah plant (Luffa cylindrica) as core material and wooden veneer as the skin layer to be used in areas of lead construction. Three different panel variations were produced for the tests, with a fiber-adhesive ratio between 1:1.05, 1:0.8, and 1:0.5. The mechanical strength (flexural strength and internal bond) and the physical properties (density and thickness swelling) were determined as a function of the fiber-adhesive composition. The results show that the flexural strength increased by approx. 400% and the thickness swelling was reduced by 10% with increasing adhesive quantity.

Vacuum Low-Temperature Microwave-Assisted Pyrolysis of Technical Lignins.

Cleavage by microwave-assisted pyrolysis is a way to obtain higher-value organic chemicals from technical lignins. In this report, pine kraft lignin (PKL), spruce and beech organosolv lignin (SOSL and BOSL), and calcium lignosulfonates from spruce wood (LS) were pyrolyzed at temperatures between 30 and 280 °C using vacuum low-temperature, microwave-assisted pyrolysis. The mass balance, energy consumption, condensation rate, and pressure changes of the products during the pyrolysis process were recorded. Phenolic condensates obtained at different temperatures during pyrolysis were collected, and their chemical composition was determined by GC-MS and GC-FID. The origin of the technical lignin had a significant influence on the pyrolysis products. Phenolic condensates were obtained in yields of approximately 15% (PKL and SOSL) as well as in lower yields of 4.5% (BOSL) or even 1.7% (LS). The main production of the phenolic condensates for the PKL and SOSL occurred at temperatures of approximately 140 and 180 °C, respectively. The main components of the phenolic fraction of the three softwood lignins were guaiacol, 4-methylguaiacol, 4-ethylguaiacol, and other guaiacol derivatives; however, the quantity varied significantly depending on the lignin source. Due to the low cleavage temperature vacuum, low-temperature, microwave-assisted pyrolysis could be an interesting approach to lignin conversion.

Bonding Acetylated Veneer for Engineered Wood Products-A Review.

The purpose of this review is to put previous research findings on acetylated wood and the fabrication of veneer-based products in a common context. The first research on wood acetylation was already conducted in the 1920s using wood meal, whereas relevant research on veneer acetylation was published nearly two decades later, during the 1940s. In the years that followed, a great deal of research has been done on both solid wood and composite acetylation. Developments in the 1990s and early 2000s resulted in the creation of commercial products. Nowadays, wood is becoming increasingly popular in construction. Therefore, high-performance materials with high dimensional stability and durability are required. Veneers are thereby of particular relevance because of their propensity to absorb chemicals into even tough-to-treat wood species. However, acetylation alters the bonding properties of wood, which is important for the manufacture of engineered veneer products, especially in load-bearing construction. A large amount of research is now being conducted on the acetylation of veneer, and acetylated veneer products are anticipated in the near future. This study covers the fundamentals of bonding but focuses specifically on veneer acetylation and its fabrication to engineered veneer-based products. The influencing factors of acetylation on bonding are also discussed.

Lignin and Lignin-Derived Compounds for Wood Applications-A Review.

Improving the environmental performance of resins in wood treatment by using renewable chemicals has been a topic of interest for a long time. At the same time, lignin, the second most abundant biomass on earth, is produced in large scale as a side product and mainly used energetically. The use of lignin in wood adhesives or for wood modification has received a lot of scientific attention. Despite this, there are only few lignin-derived wood products commercially available. This review provides a summary of the research on lignin application in wood adhesives, as well as for wood modification. The research on the use of uncleaved lignin and of cleavage products of lignin is reviewed. Finally, the current state of the art of commercialization of lignin-derived wood products is presented.

Determination of fungal activity in modified wood by means of micro-calorimetry and determination of total esterase activity.

Beech and pine wood blocks were treated with 1,3-dimethylol-4,5-dihydroxyethylen urea (DMDHEU) to increasing weight percent gains (WPG). The resistance of the treated specimens against Trametes versicolor and Coniophora puteana, determined as mass loss, increased with increasing WPG of DMDHEU. Metabolic activity of the fungi in the wood blocks was assessed as total esterase activity (TEA) based on the hydrolysis of fluorescein diacetate and as heat or energy production determined by isothermal micro-calorimetry. Both methods revealed that the fungal activity was related with the WPG and the mass loss caused by the fungi. Still, fungal activity was detected even in wood blocks of the highest WPG and showed that the treatment was not toxic to the fungi. Energy production showed a higher consistency with the mass loss after decay than TEA; higher mass loss was more stringently reflected by higher heat production rate. Heat production did not proceed linearly, possibly due to the inhibition of fungal activity by an excess of carbon dioxide.

Degradation of acrylic copolymers by white-rot fungi.

Various water-soluble homopolymers and copolymers of acrylamide (AAm) and acrylic acid (AA) which contained phenolic sites, such as guaiacol, lignin sulfonate (LS) and 3,4-dihydroxybenzoic acid (3,4-DHBA), were tested with regard to their degradability by white-rot fungi. Compared with Phanerochaete chrysosporium, Pleurotus ostreatus caused a significantly higher decrease in the average molecular weight ( Mw) of most of the copolymers and the homopolymer under the applied culture conditions. However, the Mw of poly(guaiacol/AAm) increased significantly during incubation with Pl ostreatus. P. chrysosporium was able to reduce only the Mw of the poly(LS/AA) to a significant degree and not that of the other polymers. The mineralization rate of AAm and AA copolymers and terpolymers of AAm, AA and phenolics (LS, 3,4-DHBA, guiacol), which were tested with P. ostreatus and Trametes versicolor, turned out to be low (0.8-3.2%). While the rates of mineralization were similar among all polymers, the decrease in radioactivity from the culture media was higher with the terpolymers bearing phenolic sites. UV spectra of the culture media revealed that the phenolic sites in the terpolymers were significantly degraded by both fungi. Obviously, the degradation of phenolics within the polymer chain caused a higher decrease in Mw but did not significantly increase the mineralization rate.

Lignification and structural biomass production in tobacco with suppressed caffeic/5-hydroxy ferulic acid-O-methyl transferase activity under ambient and elevated CO concentrations.

To investigate the relationship between growth, biomass partitioning and lignification we used tobacco (Nicotiana tabacum) in which O-methyl transferase (OMT) activity, an enzyme involved in the pathway of sinapyl alcohol formation for lignin synthesis, was suppressed by antisense transformation. To modulate growth, controls and transformed tobacco plants were grown under ambient (approximately 380 p.p.m) or elevated CO(2) (700 p.p.m), respectively. Lignin concentrations and composition were determined with spectrophotometric methods (thioglycolate and acetyl bromide) and Fourier transform infrared (FTIR) spectroscopy, respectively. A comparison of the thioglycolate and acetylbromide method suggested that the thioglycolate method was sensitive to changes in the syringyl/guaiacyl (S/G)-ratio in lignin and therefore not suitable for quantification in tissues with altered lignin composition. Growth under elevated CO(2) increased leaf and stem biomass of both genotypes by 40 and 20%, respectively, compared with ambient CO(2) and had no effect on root biomass. OMT suppression did not affect lignin concentrations in the leaves but caused a shift in biomass partitioning from the structural to the non-structural fraction. Elevated CO(2) caused a shift towards production of structural compounds resulting in decreased foliar lignin concentrations and indicating that the lignin/structural mass ratio is flexible in leaves. By contrast, the lignin concentrations of stems were unaffected by elevated CO(2) or OMT suppression and increased about three-fold from the apex to the base. Antisense-OMT plants produced more stem biomass than controls but showed no changes of the relative partitioning of biomass to the different pools. This indicates that the metabolic control of carbon fluxes to the production of structural versus non-structural fractions is tighter in stems than in leaves. FTIR spectroscopy indicated a relative increase in guaiacyl- as compared with syringyl-units in antisense-OMT tobacco, which was more pronounced under elevated as compared with ambient CO(2). Since there was no evidence for decreased lignin concentrations in the antisense-OMT plants but increased biomass formation we suggest that less methylated lignins are 'cheaper' in biosynthetic carbon and energy demand and, thus, may enable plants to allocate increased resources to growth.

Elevated pCO2 affects N-metabolism of young poplar plants (Populus tremula × P. alba) differently at deficient and sufficient N-supply.

• The effects of N-availability and elevated atmospheric CO 2 partial pressure ( pCO2 ) on growth, allometry and N-metabolism of poplar plants are reported here. • Poplar plants were grown hydroponically at deficient and sufficient N-supply under ambient and elevated pCO2 . The N-fluxes within the plants were estimated by comparing the fate of newly acquired 15 N-NO3 - in plants either severely N-limited or with sufficient N-supply. • At deficient N-supply, plants accumulated less biomass and exhibited an increased root : shoot ratio compared with sufficient N-supply; a larger fraction of newly acquired 15 N was allocated to the youngest leaves immediately after exchange of the nutrient solution. Increasing the external N-supply from deficient to sufficient shifted the site of nitrate reduction from roots to leaves. • Elevated pCO2 increased total biomass and the root : shoot ratio at deficient N-supply, but had no effect at sufficient N-supply. Elevated pCO2 decreased rates of N-uptake in both treatments. Increased root : shoot ratio at deficient N-supply coincided with enhanced nitrate reduction in the root and elevated pCO2 also enhanced the allocation of newly acquired 15 N to the youngest leaves. Root nitrate reduction as a possible factor controlling the root : shoot ratio and N-allocation is discussed.