Continuous adsorptive removal of glimepiride using multi-walled carbon nanotubes in fixed-bed column.

Water pollution by emerging pollutants such as pharmaceutical and personal care products is one of today's biggest challenges. The presence of these emerging contaminants in water has raised increasing concern due to their frequent appearance and persistence in the aquatic ecosystem and threat to health and safety. The antidiabetic drug glimepiride, GPD, is among these compounds, and it possesses adverse effects on human health if not carefully administered. Several conventional processes were proposed for the elimination of these persistent contaminants, and adsorption is among them. Therefore, in this study, the adsorptive removal of GPD from water using multi-walled carbon nanotubes (MWCNT) supported on silica was explored on a fixed-bed column. The effects of bed-height, solution pH, and flow rate on the adsorptive removal of GPD were investigated. The obtained adsorption parameters using Sips, Langmuir, and Freundlich models were used to investigate the continuous adsorption. The results showed that the drug removal is improved with the increasing bed height; however, it decreased with the flow rate. The effect of pH indicated that the adsorption is significantly affected and increased in acidic medium. The convection-dispersion model coupled with Freundlich isotherm was developed and used to describe the adsorption breakthrough curves. The maximum adsorption capacity (qm) was 275.3 mg/g, and the axial dispersion coefficients were ranged between 3.5 and 9.0 × 105 m2/s. The spent adsorbent was successfully regenerated at high pH by flushing with NaOH.

A combined experimental and density functional theory study of metformin oxy-cracking for pharmaceutical wastewater treatment.

Pharmaceutical compounds are emerging contaminants that have been detected in surface water across the world. Because conventional wastewater treatment plants are not designed to treat such pollutants, new technologies are needed to degrade and oxidize such contaminants. The newly developed oxy-cracking process was utilized to treat the antidiabetic drug, metformin. The process, which involved partial oxidation of metformin in alkaline aqueous medium, proved to decompose the drug into small organic molecules, with minimum emission of CO2, therefore, increasing its biodegradability and removal from industrial treatment plants. The reaction gaseous products were probed by online gas chromatography. The liquid phase before and after oxy-cracking was analyzed for total carbon content by TOC and gas chromatography mass spectrometry. The products formed from the nitrogen-rich drug included ammonia, amines, amidines, and urea derivatives. A reaction mechanism for the oxy-cracking process is proposed. Because the hydroxyl radical (˙OH) is believed to play a central role in the oxy-cracking process, the mechanism is initiated by ˙OH attacks on metformin, followed by single decomposition or isomerization steps into stable products. The reactions were investigated using density functional theory calculations and validated using high quality 2nd order Møller-Plesset perturbation theory energy calculations.

Fixed-bed column studies of total organic carbon removal from industrial wastewater by use of diatomite decorated with polyethylenimine-functionalized pyroxene nanoparticles.

In this study, a fixed-bed column adsorption process was employed to remove organic pollutants from a real industrial wastewater effluent using polyethylenimine-functionalized pyroxene nanoparticles (PEI-PY) embedded into Diatomite at very low mass percentage. Various dynamic parameters (e.g., inlet concentration, inlet flow rate, bed height, and PEI-nanoparticle concentration in Diatomite, (%nps)) were investigated to determine the breakthrough behavior. The obtained breakthrough curves were fit with a convection-dispersion model to determine the characteristic parameters based on mass transfer phenomena. The axial dispersion coefficient (DL) and group of dimensionless numbers; including Renold number (Re), Schmidt number (Sc), and Sherwood number (Sh) were all determined and correlated by Wilson-Geankoplis correlation that was used to estimate the external film diffusion coefficients (Kc) at 0.0015 < Re<55.

Surface modification of carbon nanotubes with copper oxide nanoparticles for heat transfer enhancement of nanofluids.

Over the last few years, nanoparticles have been used as thermal enhancement agents in many heat transfer based fluids to improve the thermal conductivity of the fluids. Recently, many experiments have been carried out to prepare different types of nanofluids (NFs) showing a tremendous increase in thermal conductivity of the base fluids with the addition of a small amount of nanoparticles. However, little experimental work has been proposed to calculate the flow behaviour and heat transfer of nanofluids and the exact mechanism for the increase in effective thermal conductivity in heat exchangers. This study mainly focuses on the development of nanomaterial composites by incorporating copper oxide nanoparticles (CuO) onto the surfaces of carbon nanotubes (CNTs). The CNT-CuO nanocomposite was used to prepare water-based heat transfer NFs. The morphological surfaces and loading contents of the CNT-CuO nanocomposite were characterized using field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and thermogravimetric analysis (TGA) while the physical and thermal properties of the water-based nanofluids were characterized using differential scanning calorimetry (DSC), the Mathis TCi system and a viscosity meter for measuring the heat capacity, thermal conductivity and viscosity of the synthesized NFs, respectively. The heat transfer and the pressure drop studies of the NFs were conducted by a horizontal steel tube counter-flow heat exchanger under turbulent flow conditions. The experimental results showed that the developed NFs with different concentrations of modified CNTs (0.01, 0.05 and 0.1 wt%) have yielded a significant increase in specific heat capacity (102% higher than pure water) and thermal conductivity (26% higher than pure water) even at low concentration. The results also revealed that the heat rate of the NF was higher than that of the base liquid (water) and increased with increasing the concentration of nanoparticles. Furthermore, no significant effect of the nanoparticles on the pressure drop of the system was observed.