Implementing a digital infrastructure for the lab using a central laboratory server and the SiLA2 communication standard.

In this report, a fully integrated solution for laboratory digitization is presented. The approach presents a flexible and complete integration method for the digitally assisted workflow. The worker in the laboratory performs procedures in direct interaction with the digitized infrastructure that guides through the process and aids while performing tasks. The digital transformation of the laboratory starts with standardized integration of both new and "smart" lab devices, as well as legacy devices through a hardware gateway module. The open source Standardization in Lab Automation 2 standard is used for device communication. A central lab server channels all device communication and keeps a database record of every measurement, task and result generated or used in the lab. It acts as a central entry point for process management. This backbone enables a process control system to guide the worker through the lab process and provide additional assistance, like results of automated calculations or safety information. The description of the infrastructure and architecture is followed by a practical example on how to implement a digitized workflow. This approach is highly useful for - but not limited to - the biotechnological laboratory and has the potential to increase productivity in both industry and research for example by enabling automated documentation.

Bringing IoT to the Lab: SiLA2 and Open-Source-Powered Gateway Module for Integrating Legacy Devices into the Digital Laboratory.

In this article a gateway module to integrate legacy laboratory devices into the network of the digital laboratory in the 21st century is introduced. The device is based on ready to buy consumer hardware that is easy to get and inexpensive. Depending on the specific requirements of the desired application (bare embedded computer, RS232 serial port connector, IP65 certified casing and connectors) the needed investment ranges from about 95 € up to 200 €. The embedded computer runs an open source Linux operating system and can in principle be used to run any kind of software needed for communicating with the laboratory device. Here the open source SiLA2 standard is used for presenting the device's functions in the network. As an example the digital integration of a magnetic stirrer is shown and can be used as a template for other applications. A method for easy remote integration of the device to ensure an easy and consistent workflow in development, testing and usage is also presented. This incorporates a method for remote installation of SiLA2 servers on the box as well as a web frontend for administration, debugging and management of those.

Online monitoring of the cell-specific oxygen uptake rate with an in situ combi-sensor.

In a biotechnological process, standard monitored process variables are pH, partial oxygen pressure (pO2), and temperature. These process variables are important, but they do not give any information about the metabolic activity of the cell. The ISICOM is an in situ combi-sensor that is measuring the cell-specific oxygen uptake rate (qOUR) online. This variable allows a qualitative judgement of metabolic cell activity. The measuring principle of the ISICOM is based on a volume element enclosed into a small measuring chamber. Inside the measuring chamber, the pO2 and the scattered light is measured. Within a defined measuring interval, the chamber closes, and the oxygen supply for the cells is interrupted. The decreasing oxygen concentration is recorded by the pO2 optode. This measuring principle, known as the dynamic method, determines the oxygen uptake rate (OUR). Together with the scattered light signal, the cell concentration is estimated and the qOUR is available online. The design of the ISICOM is focused on functionality, sterility, long-term stability, and response time behavior so the sensor can be used in bioprocesses. With the ISICOM, measurement of online and in situ measurement of the OUR is possible. The OUR and qOUR online measurement of an animal cell batch cultivation is demonstrated, with maximum values of OUR = 2.5 mmol L-1 h-1 and a qOUR = 9.5 pmol cell-1 day-1. Information about limitation of the primary and secondary substrate is derived by the monitoring of the metabolic cell activity of bacteria and yeast cultivation processes. This sensor contributes to a higher process understanding by offering an online view on to the cell behavior. In the sense of process analytical technology (PAT), this important information is needed for bioprocesses to realize a knowledge base process control.

Introducing a Virtual Assistant to the Lab: A Voice User Interface for the Intuitive Control of Laboratory Instruments.

The introduction of smart virtual assistants (VAs) and corresponding smart devices brought a new degree of freedom to our everyday lives. Voice-controlled and Internet-connected devices allow intuitive device controlling and monitoring from all around the globe and define a new era of human-machine interaction. Although VAs are especially successful in home automation, they also show great potential as artificial intelligence-driven laboratory assistants. Possible applications include stepwise reading of standard operating procedures (SOPs) and recipes, recitation of chemical substance or reaction parameters to a control, and readout of laboratory devices and sensors. In this study, we present a retrofitting approach to make standard laboratory instruments part of the Internet of Things (IoT). We established a voice user interface (VUI) for controlling those devices and reading out specific device data. A benchmark of the established infrastructure showed a high mean accuracy (95% ± 3.62) of speech command recognition and reveals high potential for future applications of a VUI within the laboratory. Our approach shows the general applicability of commercially available VAs as laboratory assistants and might be of special interest to researchers with physical impairments or low vision. The developed solution enables a hands-free device control, which is a crucial advantage within the daily laboratory routine.

A smart device application for the automated determination of E. coli colonies on agar plates.

The manual counting of colonies on agar plates to estimate the number of viable organisms (so-called colony-forming units-CFUs) in a defined sample is a commonly used method in microbiological laboratories. The automation of this arduous and time-consuming process through benchtop devices with integrated image processing capability addresses the need for faster and higher sample throughput and more accuracy. While benchtop colony counter solutions are often bulky and expensive, we investigated a cost-effective way to automate the colony counting process with smart devices using their inbuilt camera features and a server-based image processing algorithm. The performance of the developed solution is compared to a commercially available smartphone colony counter app and the manual counts of two scientists trained in biological experiments. The comparisons show a high accuracy of the presented system and demonstrate the potential of smart devices to displace well-established laboratory equipment.