Fractionation of eleven elements by chemical bonding from airborne particulate matter collected in an industrial city in Argentina.

A four-step chemical sequential extraction procedure was used to evaluate the distribution of Al, As, Cr, Cu, Fe, Mn, Ni, Pb, Ti, V and Zn in airborne particulate matter collected on glass fibre filters using a high-volume sampler. Two sets of samples were collected in 2001 (winter and summer campaigns) in representative zones of an industrial city of Argentina. The leaching scheme was applied to PM-10 particles and consisted in extracting the elements in four fractions, namely soluble and exchangeable elements; carbonates, oxides and reducible elements; bound to organic matter and sulfidic metals; and residual elements. Metals and metalloids at microg g(-1) level were determined in each fraction by inductively coupled plasma optical emission spectrometry (ICP OES). Analyte concentration varied from 14 microg g(-1) (equivalent to 1.0 ng m(-3)) for As to 11.8 mg g(-1) (equivalent to 2,089 ng m(-3)) for Al. Seven elements, namely Al, Cr, Fe, Mn, Pb, Ti and Zn showed similar distributions in both seasons while As was distributed in a significantly different manner in each season. The results exhibited low As contents in the first and second fractions that could be associated with routine coal combustion and a high content in the third and fourth fractions of the summer samples that could be linked to the use of pesticides. Aluminium, As, Cu, Mn, Ni, Ti, V and Zn were found in different percentages in the more bioavailable aqueous fraction with As, Mn, V and Zn exhibiting solubilities greater than 1% while Cr and Pb being insoluble. The content of Al, Cr, Cu, Fe, Ni, Pb, and Zn in the residual fraction was, in average, higher than 50%. A comparative assessment of the use of the underlying information available from fractionation studies compared to that obtained from total element content was done for Fe and Mn. It showed that the results obtained using chemical sequential extraction procedures allowed further discrimination of the potential air pollution sources.

A study of uniformity of elements deposition on glass fiber filters after collection of airborne particulate matter (PM-10), using a high-volume sampler.

A study was conducted to evaluate the homogeneity of the distribution of metals and metalloids deposited on glass fiber filters collected using a high-volume sampler equipped with a PM-10 sampling head. The airborne particulate matter (APM)-loaded glass fiber filters (with an active surface of about 500cm(2)) were weighed and then each filter was cut in five small discs of 6.5cm of diameter. Each disk was mineralized by acid-assisted microwave (MW) digestion using a mixture of nitric, perchloric and hydrofluoric acids. Analysis was performed by axial view inductively coupled plasma optical emission spectrometry (ICP OES) and the elements considered were: Al, As, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Sb, Ti and V. The validation of the procedure was performed by the analysis of the standard reference material NIST 1648, urban particulate matter. As a way of comparing the possible variability in trace elements distribution in a particular filter, the mean concentration for each element over the five positions (discs) was calculated and each element concentration was normalized to this mean value. Scatter plots of the normalized concentrations were examined for all elements and all sub-samples. We considered that an element was homogeneously distributed if its normalized concentrations in the 45 sub-samples were within +/-15% of the mean value ranging between 0.85 and 1.15. The study demonstrated that the 12 elements tested showed different distribution pattern. Aluminium, Cu and V showed the most homogeneous pattern while Cd and Ni exhibited the largest departures from the mean value in 13 out of the 45 discs analyzed. No preferential deposition was noticed in any sub-sample.

Evaluation of vapor generation for the determination of nickel by inductively coupled plasma-atomic emission spectrometry.

Volatile species of Ni were generated by merging acidified aqueous samples and sodium tetrahydroborate(III) in a continuous flow system. The gaseous analyte was subsequently introduced via a stream of Ar carrier into the inlet tube of the plasma torch. Inductively coupled plasma atomic emission spectrometry (ICP-AES) was used for detection. The operating conditions (chemical and physical parameters) and the concentrations of different acids were evaluated for the efficient generation of Ni vapor. The detection limit (3 sigma(blank)) was 1.8 ng mL(-1). The precision (RSD) of the determination was 4.2% at a level of 500 ng mL(-1) and 7.3% for 20 ng mL(-1) (n=10). The efficiency of the generation process was estimated to be 51%. The possible interfering effect of transition metals (Cd, Co, Cu, Cr, Fe, Mn, Zn), hydride forming elements (As, Ge, Pb, Sb, Se, Sn, Te), and Hg on Ni signal was examined. This study has demonstrated that Ni vapor generation is markedly free of interferences.