ABSTRACT
The article discusses the phenomena and destructive mechanisms occurring on the surface of 1.2344 steel dies used during the hot forging of disc-type forgings. Preliminary research has shown that gas nitriding alone, used so far, is insufficient due to the occurrence of destructive mechanisms other than abrasive wear, such as thermal and thermomechanical fatigue, which cause the average durability of such tools to be approximately 5000 forgings. Analyses were also carried out to assess the load on forging tools using numerical modeling (Forge 3.0NxT), which confirmed the occurrence of large and cyclically changing thermal and mechanical loads during the forging process. Therefore, in order to increase operational durability, it was decided to use two types of hybrid layers, differing in the PVD coating used: TiCrAlN and CrN, and then subjected to gas nitriding (GN). The obtained results showed that, depending on the area of the tool and the current working conditions, the applied PVD coatings protect the surface layer of the tool against the dominant destructive mechanisms. In both cases, the strength increased to the level of 7000 forgings, the tools could continue to work, and globally, slightly better results were obtained for the GN+TiCrAlN layer. The CrN-type layer protects the tool more against thermal fatigue, while the TiCrAlN layer is more resistant to abrasive wear. In areas where the hybrid layer was worn, a decrease in hardness was observed from 1300 HV to 600-700 HV, and in places of intense material flow (front-point 2 and tool bridge-point 9) the hardness dropped to below 400 HV, which may indicate local tempering of the material. Moreover, the research has shown that each process and tool should be analyzed individually, and the areas in the tool where particular destructive mechanisms dominate should be identified, so as to further protect the forging tool by using appropriate protective coatings in these areas.
ABSTRACT
This study refers to an analysis of the durability of forging tools applied in the second operation of producing a valve forging from the chromium-nickel steel, NC3015. Due to the extreme working conditions of the tools, caused by cyclic thermo-mechanical loads, the average durability of tools made from tool steel WLV (1.2365) equals about 1500 forgings. An in-depth, complex analysis was performed on the technology, using macroscopic tests combined with a measurement of the wear/allowance on the tool working surface through 3D scanning; microstructural tests by means of light microscopy; observations of the changes taking place on the working surface with a scanning electron microscope; microhardness measurements; and multi-variant numerical simulations. It was established that the key issue is the proper selection of the process technological parameters, such as the input material and tool temperature, friction, lubrication, tribological parameters, type of tool material, or punch design, because even small changes made to them significantly affect the service life of forging punches. Therefore, to increase the durability of the forging dies, alternative materials made of W360, as well as two high speed steels, S600 and S705, were applied. However, the implemented punch materials did not bring the assumed effect of increased durability, as the highest average durability of steel W60 equaled only 1500 forgings, whereas in the case of the tool steels, this was below 900 forgings. For this reason, at the further stage, punches with sintered carbide inserts were introduced, which made it possible to significantly improve the durability up to the level of as many as 20,000 forgings, which, at the same time, points to a promising direction of further studies on the use of materials and solutions of this type.
ABSTRACT
This study performs a complex analysis and review of the currently applied methods of inductively heating the charge material in hot die forging processes, as well as elaborates and verifies a more effective heating method. On this basis, a device for inductive heating using variable frequency inductors was designed and constructed, which made it possible to reduce the scale and decarburization with respect to the heater used so far. In the first place, the temperature distributions in the heater in the function of time were modeled with the use of the CEDRAT FLUX software. The aim of the research was to analyze the temperature gradient and value diversification on the surface and in the material core, as well as to determine the process stability. The following stage was designing and constructing a heater with an automatic system of loading and positioning of the charge on the exit, as well as with a possibility of working in a fully automated system adjusted to the work center. The last stage of investigations was the verification of the elaborated effective heating method on the basis of a short production series and a continuous work for the period of 8 h, both in the quantitative and qualitative aspect (reduced oxidation and decarburization as well as a gradient between the core and the surface). The obtained results confirm the effectiveness of the proposed solution referring to heating the charge material, especially in the aspect of stability and repeatability of the process, as well as a significant reduction in oxidation and decarburization of the material surface.
ABSTRACT
This article presents the results of a comparative analysis performed with respect to the wear of tools used for the extrusion of a clay strand (for ceramic roof tile) made from two materials: steel NC11LV and steel Hardox 600. The aim of the studies was to determine the causes and mechanisms of wear as well as to evaluate the possibility of choosing the optimal material, mostly in respect to its resistance to intensive wear as well as an increase in the operation time. The results of the conducted investigations included: an analysis of the technology, thermovision measurements of the forming process, a macroscopic analysis combined with 3D scanning of the worn tools, ball-on-disc tests of the sliding wear resistance and hardness measurements. The obtained results demonstrated that the tools made of steel NC11LV were much less worn than those made of steel Hardox 600, as the operation time for the NC11LV steel tools was almost three times longer. The results of the ball-on-disc tests showed a similar manner of wear for both materials (with the working temperature of about 50 °C). The higher durability of the tools made from steel NC11LV can be an effect of a slightly lower coefficient of friction in the initial period of operation as well as the presence of hard carbides, which means increased hardness and thus also higher wear resistance at working temperatures.
ABSTRACT
The study performs a comparative analysis of the wear of tools made of two wear-resistant materials: steel Hardox 600 and NC11LV, used in the process of forming a band for roofing tiles. The analyses were to allow the assessment of the possibility of replacing the standard material for tools in this process with a much less expensive tool steel for cold work after heat treatment (with a large number of carbides), as an alternative material dedicated to tools resistant to intense abrasive wear. The performed investigations included a macroscopic and geometrical analysis with the use of 3D scanning, microstructural analyses conducted by means of a light microscope, as well as an analysis of the topography of the working areas of the tools with the use of SEM, and microhardness tests. The obtained results demonstrate that the tools made of both materials were characterized with a similar level of wear, which, in the most critical area, reached over 4 mm, while the tools made of steel NC11LV worked over a much longer period of time without regeneration, equaling 912 h, and an insert made of steel Hardox 600 operated for 384 h. A higher tool life in the case of NC11LV steel may be the result of higher hardness and the presence of hard carbides.
