The influence of drill length and irrigation system on heat production during osteotomy preparation for dental implants: an ex vivo study.

OBJECTIVE: This study aimed to measure the influence of drill length and irrigation system on heat production during osteotomy preparation for dental implants using bovine bone rib as experimental model. MATERIALS AND METHODS: Three groups were created: Group 1: drilling with three consecutive burs with double irrigation (internal and external) for a 4.0 mm conical implant; and Group 2 and Group 3: drilling with three consecutive burs with external irrigation for a 4.1 mm cylindrical implant and for a 4.3 mm conical implant, respectively. Four lengths were tested: 10, 12, 14 and 16 mm; in site prepared on bovine ribs using a surgical unit linked to a testing device, to standardize and simulate implant drilling procedures. Bone temperature variations were recorded using three thermocouples in different positions as of the crestal bone: 2 mm, position (p1); 7 mm, position 2 (p2); and 12 mm, position 3 (p3). RESULTS: The highest temperature changes were invariably recorded during the process of withdrawal. Significantly lower temperature changes (P < 0.02) could be recorded at maximum drilling depths during the shearing process regardless of drilling depth or irrigation method. Double irrigation was associated with significantly lower temperatures compared with external irrigation by the use of implant drills (P < 0.01). CONCLUSIONS: Within the limitations of this ex vivo study was possible concluded that the use a double irrigation system in multiple conventional drill for osteotomy can decrease the heat generation when increase the drill length.

Effects on the osseointegration of titanium implants incorporating calcium-magnesium: a resonance frequency and histomorphometric analysis in rabbit tibia.

OBJECTIVE: This study assessed the bone formation around titanium surface incorporating the calcium-magnesium (CaMg) deposited by blasted in rabbit tibia bone to determine whether this surface would further enhance bone healing compared with commercially available implant surface. MATERIAL AND METHODS: The deposition of CaMg on the titanium SLA surface were obtained by blasting formed the experimental group (EX group), while implants with traditional SLA surface were used as control group (CO group), in this study. Fifty cylindrical threaded implants with a length of 8 mm were used (P = 25 per group). Five implants of each group were used to surface characterization by scanning electron microscopy, energy dispersive spectrometry, and optical profilometry. Ten New Zealand white rabbits received 40 implants (n = 20 per group). Resonance frequency analysis was performed three times (0, 4, and 6 weeks). Histomorphometric analysis was performed 4 and 6 weeks after implantation. Statistical significance was set at P < 0.05. RESULTS: Blasted CaMg deposition on SLA implant surface displayed almost identical surface morphologies and R(a) values at the micron scale. In comparing the implant stability quotient at the three time points, highly significant statistic differences were found (P < 0.001). Histomorphological analysis showed higher degrees of bone organization in the samples of test implant surfaces at both implantation times. CONCLUSION: Within the limitations of this study, the results indicate that the deposition of CaMg on the SLA titanium surface may be effective in enhancing the osseointegration of moderately rough grit-blasted implants by increasing the degree of bone-implant contact.

Stability and Crestal Bone Behavior Following Simultaneous Placement of Multiple Dental Implants (Two or More) with the Bone Splitting Technique: A Clinical and Radiographic Evaluation.

PURPOSE: The present study aimed to measure the implant stability quotient (ISQ) values at three different time points after surgical procedures and crestal bone behavior in multiple implants (two or more) installed simultaneously with the bone splitting technique. MATERIALS AND METHODS: For this study, 45 patients with different edentulous areas in the maxilla were selected, and a total of 114 dental implants were installed. Implant stability was measured by resonance frequency analysis immediately following implant placement to assess immediate stability (time 1) and stability at 90 days (time 2), and 150 days (time 3). Crestal bone height was measured in peri-apical radiographs at 90 and 150 days after implantation in relation to each implant shoulder, given that the implants were installed at the level of the crestal bone. RESULTS: Six implants were not osseointegrated. Overall, the means and standard deviations of the ISQ values were 60.3 ± 4.94 (95% confidence interval [CI], 44-69) at baseline, 66.6 ± 5.28 (95% CI, 49-75) at 90 days, and 72.1 ± 4.28 (95% CI, 59-79) at 150 days (p < 0.0001). The mean marginal bone loss of the implants was 1.11 ± 0.61 mm on the mesial side and 1.17 ± 0.61 mm on the distal side at time 2, and 1.73 ± 0.68 mm on the mesial side and 1.79 ± 0.70 mm on the distal side at time 3. A strong positive correlation between implant stability and bone loss was detected (p < 0.0001). CONCLUSIONS: Within the limits of this study, the bone splitting technique with simultaneous implant installation exhibited a good success rate with respect to the osseointegration index but requires attention with respect to crestal bone behavior.