Hybrid Mesoporous TiO2/ZnO Electron Transport Layer for Efficient Perovskite Solar Cell.

In recent years, perovskite solar cells (PSCs) have gained major attention as potentially useful photovoltaic technology due to their ever-increasing power-conversion efficiency (PCE). The efficiency of PSCs depends strongly on the type of materials selected as the electron transport layer (ETL). TiO2 is the most widely used electron transport material for the n-i-p structure of PSCs. Nevertheless, ZnO is a promising candidate owing to its high transparency, suitable energy band structure, and high electron mobility. In this investigation, hybrid mesoporous TiO2/ZnO ETL was fabricated for a perovskite solar cell composed of FTO-coated glass/compact TiO2/mesoporous ETL/FAPbI3/2D perovskite/Spiro-OMeTAD/Au. The influence of ZnO nanostructures with different percentage weight contents on the photovoltaic performance was investigated. It was found that the addition of ZnO had no significant effect on the surface topography, structure, and optical properties of the hybrid mesoporous electron-transport layer but strongly affected the electrical properties of PSCs. The best efficiency rate of 18.24% has been obtained for PSCs with 2 wt.% ZnO.

Synthesis of 1D Bi2O3 nanostructures from hybrid electrospun fibrous mats and their morphology, structure, optical and electrical properties.

The aim of this study was to produce Bi2O3 nanowires using a combination of sol-gel process and electrospinning methods and a solution based on a 13% solution of polyacrylonitrile (PAN) in N,N-dimethylformamide (DMF) containing 1.5 g of bismuth (III) nitrate pentahydrate (Bi(NO3)3·5H2O). The obtained fibrous composite mats were dried at room temperature for 24 h followed by the calcination process in air at two different temperatures of 400 °C and 600 °C. Analysis of the morphology of the fabricated Bi2O3 nanomaterials based on TEM images showed that the obtained ceramic structures could be classified as one-dimensional Bi2O3 nanostructures, with the sizes of the presented structures being 260 nm, 125 nm and 200 nm for diameter, and 5.5µm , 2 µm and 2.125 µm for length, respectively. Moreover, further analysis of the morphology of the obtained Bi2O3 nanostructures with the use of SEM showed that their diameters ranged from 150 to 500 nm when a calcination temperature of 400 °C was employed, while Bi2O3 nanowires with diameters ranging from 150 to 450 nm were obtained at 600 °C. To analyse the chemical composition and oscillatory transitions of atoms vibrating between the oscillatory levels in the molecules of the produced 1D nanostructures, and to determine the functional groups existing therein, EDX and FTIR were used. Transmission peaks in FTIR spectra recorded for wave numbers in the range of 400-4000 cm-1 were due to the presence of vibrations in Bi-O bonds, which correspond to the structure of Bi2O3. In addition, a detailed analysis of optical constants of one-dimensional Bi2O3 nanostructures fabricated using a combination of sol-gel process, electrospinning and calcination methods has been presented in this paper for the first time. Optical studies based on the recorded UV-Vis spectra showed that the obtained Bi2O3 nanowires were characterized by sharp absorption edges of radiation in the near-ultraviolet range, with sharp absorption edges falling at wavelengths of 400 nm, regardless of the applied temperature during the calcination process. The study of optical constants showed that the Bi2O3 nanostructures exhibited refractive indices of 2.62 and 2.53 at temperatures of 400 °C and 600 °C, respectively, while dielectric constants were 6.87 and 6.42, respectively. The final stage of the study was the determination of the width of energy gaps of the produced bismuth oxide nanostructures, which were found to be 3.19 and 2.97 eV, respectively. The presented results of morphology and optical properties of the obtained one-dimensional Bi2O3 semiconductor nanostructures indicate a potential possibility to apply this type of materials for the production of a new generation of dye-sensitized photovoltaic cells (DSSCs).

Effect of polyaniline content and protonating dopants on electroconductive composites.

Elastic constructive elements prepared by electrospinning using polyacrylonitrile/polyaniline (PAN/PANI) electroconductive composites were prepared and investigated in terms of their thermal and mechanical properties. This study was focused on the impact of the type of counterion of polyaniline and the PANI content in composites on the thermal, conductive and morphological properties of electrospun fibers. In this study, composites obtained from PANI doped with sulfuric acid showed the highest conductivity, and composites obtained from PANI doped with hydrochloric acid showed the highest thermal stability. All obtained composites exhibited good thermal stability, with T5 values in the range of 230-268 °C that increased with increasing PANI content. The prepared composites exhibited comparable PAN Tg values, which indicates their suitability for processing. Instrumental analysis of polymers and composites was carried out using UV-visible spectroscopy, thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical thermal analysis and scanning electron microscopy.

Synthesis of hybrid amorphous/crystalline SnO2 1D nanostructures: investigation of morphology, structure and optical properties.

The aim of the study was to prepare SnO2 nanowires via a combination of electrospinning and the sol-gel method from a polyvinylpyrrolidone (PVP)/dimetylformamide (DMF)/ethanol(EtOH)/tin(IV) chloride pentahydrate (SnCl4·5H2O) solution. The morphology, structure and chemical composition of the obtained PVP/SnO2 nanofibers and SnO2 nanowires were examined using transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR) as well as a scanning electron microscope (SEM) with an energy dispersive spectrometer (EDX). The optical property analysis was performed on the basis of UV-Vis spectra of absorbance as a function of the wavelength, based on which the rated values of band gaps of the fabricated 1D nanostructures were determined. The morphology analysis showed that the obtained amorphous SnO2 nanowires with crystalline protuberances were characterized by a diameter of 50 to 120 nm. Results demonstrated that nanowires with a ratio of 1:1 precursor to polymer in the spinning solution were characterized by the smallest diameter after calcination and the smallest energy gap of 3.3 eV among all investigated samples. The rest of the studied materials were characterized by a larger energy gap (3.8 and 3.9 eV).

Synthesis of the Novel Type of Bimodal Ceramic Nanowires from Polymer and Composite Fibrous Mats.

The purpose of this paper was to produce SiO2 and TiO2 nanowires via the electrospinning process from a polyvinylpyrrolidone (PVP)/Tetraethyl orthosilicate (TEOS)/Titanium (IV) butoxide (TNBT)/dimethylformamide (DMF) and ethanol (EtOH) solution. The as-obtained nanofibers were calcined at temperatures ranging from 400 °C to 600 °C in order to remove the organic phase. The one-dimensional ceramic nanostructures were studied using a scanning electron microscope (SEM) and a transmission electron microscope (TEM) to analyze the influence of the used temperature on the morphology and structures of the obtained ceramic nanomaterials. In order to examine the chemical structure of the nanowires, energy dispersive spectrometry (EDX) and Fourier-Transform Infrared spectroscopy (FTIR) were used. The optical property analysis was performed on the basis of UV-Vis spectra of absorbance as a function of the wavelength. Using the modified Swanepoel method, which the authors proposed and the recorded absorbance spectra allowed to determine the banded refractive index n, real n' and imaginary k part of the refractive index as a function of the wavelength, complex dielectric permeability ε, and real and imaginary part εr and εi of the dielectric permeability as a function of the radiation energy of the produced ceramic nanowires.

Manufacturing and investigation of physical properties of polyacrylonitrile nanofibre composites with SiO2, TiO2 and Bi2O3 nanoparticles.

The aim of this study was to produce nanocomposite polymer fibres, consisting of a matrix of polyacrylonitrile (PAN) and a reinforcing phase in the form of SiO2/TiO2/Bi2O3 nanoparticles, by electrospinning the solution. The effect of the nanoparticles and the electrospinning process parameters on the morphology and physical properties of the obtained composite nanofibres was then examined. The morphology of the fibres and the dispersion of nanoparticles in their volume were examined using scanning electron microscopy (SEM). All of the physical properties, which included the band gap width, dielectric constant and refractive index, were tested and plotted against the concentration by weight of the used reinforcing phase, which was as follows: 0%, 4%, 8% and 12% for each type of nanoparticles. The width of the band gap was determined on the basis of the absorption spectra of radiation (UV-vis) and ellipsometry methods. Spectroscopic ellipsometry has been used in order to determine the dielectric constant, refractive index and the thickness of the obtained fibrous mats.