Performance of Oriented Strand Board Made of Heat-Treated Bamboo (Dendrocalamus asper (Schult.) Backer) Strands.

This study aimed to analyze the effect of pre-heat treatment on bamboo strand properties and its impact on the properties of the resulting bamboo-oriented strand board (BOSB). Giant bamboo (Dendrocalamus asper (Schult.) Backer) with a density of 0.53 g cm-3 was converted into bamboo strands. These strands were pre-heat-treated at 140 and 160 °C for a duration of 1, 2, and 3 h. Changes in the chemical composition of the strand due to subsequent treatment were assessed. Fourier-transform infrared spectroscopy (FTIR) and X-Ray diffraction analysis (XRD) were used to determine the changes in the chemical composition of bamboo strands. The BOSB panels were produced with a target density of 0.7 g cm-3. The manufacturing of the BOSB was conducted in three layers with a ratio of 25:50:25, bonded with phenol-formaldehyde resin. The physical and mechanical properties of the laboratory-fabricated BOSB were tested in compliance with the criteria given in JIS A 5908 standards. Comparisons were made against OSB CSA 0437.0 Grade O-1 commercial standard. The pre-heat treatment led to chemical alterations within the material when set at 140 and 160 °C for 1 to 3 hours (h). FTIR spectral analysis demonstrated that longer exposure and higher temperatures resulted in fewer functional groups within the bamboo strands. The increased temperature and duration of pre-heat treatment enhanced the crystallinity index (CI). The dimensional stability and mechanical properties of the composites were improved significantly as hemicellulose and extractive content were reduced. This study demonstrated that the pre-heat treatment of bamboo strands at a temperature of 160 °C for a duration of 1 h was an adequate approach for heat modification and fabrication of BOSB panels with acceptable properties according to OSB CSA 0437.0 Grade O-1 commercial standard.

The nematode effector Mj-NEROSs interacts with Rieske's iron-sulfur protein influencing plastid ROS production to suppress plant immunity.

Root-knot nematodes (RKN; Meloidogyne species) are plant pathogens that introduce several effectors in their hosts to facilitate infection. The actual targets and functioning mechanism of these effectors largely remain unexplored. This study illuminates the role and interplay of the Meloidogyne javanica nematode effector ROS suppressor (Mj-NEROSs) within the host plant environment. Mj-NEROSs suppresses INF1-induced cell death as well as flg22-induced callose deposition and reactive oxygen species (ROS) production. A transcriptome analysis highlighted the downregulation of ROS-related genes upon Mj-NEROSs expression. NEROSs interacts with the plant Rieske's iron-sulfur protein (ISP) as shown by yeast-two-hybrid and bimolecular fluorescence complementation. Secreted from the subventral pharyngeal glands into giant cells, Mj-NEROSs localizes in the plastids where it interacts with ISP, subsequently altering electron transport rates and ROS production. Moreover, our results demonstrate that isp Arabidopsis thaliana mutants exhibit increased susceptibility to M. javanica, indicating ISP importance for plant immunity. The interaction of a nematode effector with a plastid protein highlights the possible role of root plastids in plant defense, prompting many questions on the details of this process.

Effect of densification on the physical and mechanical properties of the inner part of oil palm trunk impregnated with methylene diphenyl diisocyanate.

Oil palm (Elaeis guineensis Jacq.) plantations in Indonesia are increasing over the past few years. After economic productivity, however, the unproductive oil palm trunks are felled and mostly go to waste, especially the inner part of the oil palm trunk (IOPT). There are several modification methods to utilize IOPT, such as impregnation and densification. Methylene diphenyl diisocyanate (MDI) is a common resin used for impregnation in composite industries because it is non-toxic and has excellent physical and mechanical properties but it has never been applied for the impregnation of IOPT. This study aimed to analyze the effect of densification on the physical and mechanical properties of the inner part of oil palm trunk (IOPT) impregnated using methylene diphenyl diisocyanate (MDI) resin to obtain valuable information regarding the efficient utilization of unproductive oil palm trunks. IOPT was densified and compregnated with compression ratios (CRs) of 20% and 30%. The physical properties (density, moisture content (MC), and water absorption (WA)) and mechanical properties (modulus of elasticity (MOE), modulus of rupture (MOR), and hardness) of the compregnated samples were better than those of the densified samples. The density and mechanical properties at CR 30% were higher than those at CR 20%. The improvements in density, MC, and WA of the compregnated IOPT with CR 30% were 127%, 54%, and 70%, respectively, compared to that in untreated IOPT. Furthermore, improvements in the MOE, MOR, and hardness of the compregnated IOPT with CR 30% were 489%, 379%, and 393%, respectively. The mechanical properties of the compregnated IOPT at CR 20% and 30% increased two- to three-fold from strength class V in control IOPT to strength class III in compregnated IOPT with CR 20% and to strength class II in compregnated IOPT with CR 30%, respectively.

Effect of Oxidation Time on the Properties of Cellulose Nanocrystals Prepared from Balsa and Kapok Fibers Using Ammonium Persulfate.

This study aimed to evaluate the effect of ammonium persulfate's (APS) oxidation time on the characteristics of the cellulose nanocrystals (CNCs) of balsa and kapok fibers after delignification pretreatment with sodium chlorite/acetic acid. This two-step method is important for increasing the zeta potential value and achieving higher thermal stability. The fibers were partially delignified using acidified sodium chlorite for four cycles, followed by APS oxidation at 60 °C for 8, 12, and 16 h. The isolated CNCs with a rod-like structure showed an average diameter in the range of 5.5-12.6 nm and an aspect ratio of 14.7-28.2. Increasing the reaction time resulted in a gradual reduction in the CNC dimensions. The higher surface charge of the balsa and kapok CNCs was observed at a longer oxidation time. The CNCs prepared from kapok had the highest colloid stability after oxidation for 16 h (-62.27 mV). The CNCs with higher crystallinity had longer oxidation times. Thermogravimetric analysis revealed that the CNCs with a higher thermal stability had longer oxidation times. All of the parameters were influenced by the oxidation time. This study indicates that APS oxidation for 8-16 h can produce CNCs from delignified balsa and kapok with satisfactory zeta potential values and thermal stabilities.