Radical scavenging of poly(methyl methacrylate) bone cement by rifampin and clinically relevant properties of the rifampin-loaded cement.

OBJECTIVES: The objective of this study was to characterize the effect of rifampin incorporation into poly(methyl methacrylate) (PMMA) bone cement. While incompatibilities between the two materials have been previously noted, we sought to identify and quantify the cause of rifampin's effects, including alterations in curing properties, mechanical strength, and residual monomer content. METHODS: Four cement groups were prepared using commercial PMMA bone cement: a control; one with 1 g of rifampin; and one each with equimolar amounts of ascorbic acid or hydroquinone relative to the amount of rifampin added. The handling properties, setting time, exothermic output, and monomer loss were measured throughout curing. The mechanical strength of each group was tested over 14 days. A radical scavenging assay was used to assess the scavenging abilities of rifampin and its individual moieties. RESULTS: Compared with control, the rifampin-incorporated cement had a prolonged setting time and a reduction in exothermic output during polymerization. The rifampin cement showed significantly reduced strength and was below the orthopaedic weight-bearing threshold of 70 MPa. Based on the radical scavenging assay and strength tests, the hydroquinone structure within rifampin was identified as the polymerization inhibitor. CONCLUSION: The incorporation of rifampin into PMMA bone cement interferes with the cement's radical polymerization. This interference is due to the hydroquinone moiety within rifampin. This combination alters the cement's handling and curing properties, and lowers the strength below the threshold for weight-bearing applications. Additionally, the incomplete polymerization leads to increased toxic monomer output, which discourages its use even in non-weight-bearing applications.Cite this article: G. A. Funk, E. M. Menuey, K. A. Cole, T. P. Schuman, K. V. Kilway, T. E. McIff. Radical scavenging of poly(methyl methacrylate) bone cement by rifampin and clinically relevant properties of the rifampin-loaded cement. Bone Joint Res 2019;8:81-89. DOI: 10.1302/2046-3758.82.BJR-2018-0170.R2.

Combination of modified mixing technique and low frequency ultrasound to control the elution profile of vancomycin-loaded acrylic bone cement.

OBJECTIVES: The objective of this study was to determine if combining variations in mixing technique of antibiotic-impregnated polymethylmethacrylate (PMMA) cement with low frequency ultrasound (LFUS) improves antibiotic elution during the initial high phase (Phase I) and subsequent low phase (Phase II) while not diminishing mechanical strength. METHODS: Three batches of vancomycin-loaded PMMA were prepared with different mixing techniques: a standard technique; a delayed technique; and a control without antibiotic. Daily elution samples were analysed using flow injection analysis (FIA). Beginning in Phase II, samples from each mix group were selected randomly to undergo either five, 15, 45, or 0 minutes of LFUS treatment. Elution amounts between LFUS treatments were analysed. Following Phase II, compression testing was done to quantify strength. A-priori t-tests and univariate ANOVAs were used to compare elution and mechanical test results between the two mix groups and the control group. RESULTS: The delayed technique showed a significant increase in elution on day one compared with the standard mix technique (p < 0.001). The transition point from Phase I to Phase II occurred on day ten. LFUS treatments significantly increased elution amounts for all groups above control. Delayed technique resulted in significantly higher elution amounts for the five-minute- (p = 0.004) and 45-minute- (p < 0.001) duration groups compared with standard technique. Additionally, the correlations between LFUS duration and total elution amount for both mix techniques were significant (p = 0.03). Both antibiotic-impregnated groups exhibited a significant decrease in offset yield stress compared with the control group (p < 0.001), however, their lower 95% confidence intervals were all above the 70 MPa limit defined by International Standards Organization (ISO) 5833-2 reference standard for acrylic bone cement. CONCLUSION: The combination of a delayed mix technique with LFUS treatments provides a reasonable means for increasing both short- and long-term antibiotic elution without affecting mechanical strength.Cite this article: Dr. T. McIff. Combination of modified mixing technique and low frequency ultrasound to control the elution profile of vancomycin-loaded acrylic bone cement. Bone Joint Res 2016;5:26-32. doi: 10.1302/2046-3758.52.2000412.

Improved gold chloride staining method for anatomical analysis of sensory nerve endings in the shoulder capsule and labrum as examples of loose and dense fibrous tissues.

Consistency in gold chloride staining is essential for anatomical analysis of sensory nerve endings. The gold chloride stain for this purpose has been modified by many investigators, but often yields inconsistent staining, which makes it difficult to differentiate structures and to determine nerve ending distribution in large tissue samples. We introduce additional steps and major changes to the modified Gairns' protocol. We controlled the temperature and mixing rate during tissue staining to achieve consistent staining and complete solution penetration. We subjected samples to sucrose dehydration to improve cutting efficiency. We then exposed samples to a solution containing lemon juice, formic acid and paraformaldehyde to produce optimal tissue transparency with minimal tissue deformity. We extended the time for gold chloride impregnation 1.5 fold. Gold chloride was reduced in the labrum using 25% formic acid in water for 18 h and in the capsule using 25% formic acid in citrate phosphate buffer for 2 h. Citrate binds gold nanoparticles, which minimizes aggregation in the tissue. We stored samples in fresh ultrapure water at 4° C to slow reduction and to maintain color contrast in the tissue. Tissue samples were embedded in Tissue Tek and sectioned at 80 and 100 µm instead of using glycerin and teasing the tissue apart as in Gairns' modified gold chloride method. We attached sections directly to gelatin subbed slides after sectioning with a cryostat. The slides then were processed and coverslipped with Permount. Staining consistency was demonstrated throughout the tissue sections and neural structures were clearly identifiable.

The effect of accuracy of implantation on range of movement of the Scandinavian Total Ankle Replacement.

When performing the Scandinavian Total Ankle Replacement (STAR), the positioning of the talar component and the selection of mobile-bearing thickness are critical. A biomechanical experiment was undertaken to establish the effects of these variables on the range of movement (ROM) of the ankle. Six cadaver ankles containing a specially-modified STAR prosthesis were subjected to ROM determination, under weight-bearing conditions, while monitoring the strain in the peri-ankle ligaments. Each specimen was tested with the talar component positions in neutral, as well as 3 and 6 mm of anterior and posterior displacement. The sequence was repeated with an anatomical bearing thickness, as well as at 2 mm reduced and increased thicknesses. The movement limits were defined as 10% strain in any ligament, bearing lift-off from the talar component or limitations of the hardware. Both anterior talar component displacement and bearing thickness reduction caused a decrease in plantar flexion, which was associated with bearing lift-off. With increased bearing thickness, posterior displacement of the talar component decreased plantar flexion, whereas anterior displacement decreased dorsiflexion.

The effect of agility ankle prosthesis misalignment on the peri-ankle ligaments.

In the Agility total ankle replacement system, motion is constrained by the implant's articulating surfaces and the peri-ankle ligaments. The effects of plausibly occurring implant malpositioning on peri-ankle ligament functional extension during walking were explored in this study. The intent was to determine whether certain ligaments could serve as guides to assist in proper component positioning at implantation. Using a cadaver preparation with simulated physiologic motion and loading, we monitored change of ligament length of the anterior talofibular, posterior talofibular, calcaneofibular, and tibiocalcaneal ligaments resulting from controlled malpositioning of the tibial component relative to a neutral position. During a simulated walking cycle, effects of mediolateral and anterior/posterior translation, internal and external rotation, inversion and eversion, and elevation of the component were evaluated. In all cases, tibial component displacement from the neutral position caused atypical length change in one or more of the peri-ankle ligaments. In particular, anterior/posterior displacement significantly changed the lengthening behavior of all four tested ligaments. The anterior talofibular ligament was sensitive to transverse plane displacements, whereas the tibiocalcaneal ligament was sensitive to coronal plane displacements. For the Agility prosthesis, these two ligaments seem to be sensitive guides for tibial component positioning at implantation.

Total ankle replacement revisited.

The surgical treatment of painful, end-stage ankle arthritis includes ankle arthrodesis and total ankle replacement. In the past decade, total ankle replacement has become a viable alternative to ankle arthrodesis. Modern implant designs either involve a syndesmosis fusion and resurfacing of the medial and lateral recesses of the ankle joint or the use of a 3-component, mobile bearing implant. In limited clinical series, the early results of both these prosthetic design approaches are encouraging. In selected patients, ankle arthroplasty is an effective approach to relieving pain and improving function. The purposes of this paper are to review the clinical results from total ankle replacement and ankle arthrodesis; discuss indications, contraindications, design features, postoperative rehabilitation, and initial results for the major current total ankle designs; and present concepts for future total ankle development. In particular, this article explores the advantages and concerns with 2 prevalent but different design approaches. It also discusses future directions for total ankle replacement.

A mechanical comparison of the dynamic compression plate, limited contact-dynamic compression plate, and point contact fixator.

Cortical bone porosis associated with the dynamic compression plate (DCP) prompted the development of the limited-contact dynamic compression plate (LC-DCP) and the point-contact fixator (PC-Fix) to increase bone vascularity. However, the comparative fixation characteristics of the three designs are unknown. Transverse fractures were physiologically created in paired cadaveric sheep tibiae, which were plated before torsion testing and four-point bending to failure. The tibiae were grouped randomly and compared as follows: DCP versus LC-DCP, DCP versus PC-Fix, and LC-DCP versus PC-Fix. Mean torque to failure demonstrated no significant difference between the three plates (p < 0.33). Mean bending stiffness, gap opening, and moment to failure also demonstrated no significant difference between the three designs with p < 0.29, < 0.13, and < 0.16, respectively. The LC-DCP and PC-Fix have torsion and bending properties comparable with the DCP in the fixation of simple transverse diaphyseal fractures.

Intramedullary pressure, strain on the diaphysis and increase in cortical temperature when reaming the femoral medullary cavity--a comparison of blunt and sharp reamers.

Clinical application has shown intramedullary nailing to be a safe therapeutic procedure, although damage to the vascular system and fat embolism have been demonstrated in animal experiments. The main negative factors were presumed to be the increase in intramedullary pressure and the increase in cortical temperature. In this study, the effect of the blunting of the reamers on the increase in intramedullary pressure, the tangential strain on the diaphysis and the increase in cortical temperature was to be clarified. The measurements were carried out on pairs of human femora reamed with sharp and blunt AO reamers. The pressure was measured in the middle of the diaphysis and in the metaphysis, the strain in the middle of the femur and the temperature on four aspects of the femur. The femora were reamed with identical compression and traction forces in a water bath at 37 degrees C. In comparison with the sharp reamer, the blunt reamer develops 2.1 times the positive diaphyseal pressure, 1.7 times the positive metaphyseal pressure, 1.6 times the negative diaphyseal pressure, 1.5 times the positive tangential strain, 55 times the negative tangential strain and 2.8 times the increase in cortical temperature. There is no difference in the negative metaphyseal pressure. Since blunt reamers produce greater intramedullary pressure values, greater tangential strain on the diaphysis and a greater increase in cortical temperature, the attention of surgeons and operating staff must be drawn to the fact that they should treat the reamers gently and replace them whenever necessary.

Influence of the compression force on the intramedullary pressure development in reaming of the femoral medullary cavity.

The reaming process is considered the main damage factor in intramedullary nailing, as there are repeated increases in intramedullary pressure and cortical temperature, which can lead to aseptic cortex necroses and fat embolisms. In this study, the influence of the compression force on the increase in pressure is to be examined. The intramedullary pressure was measured in the middle of the diaphysis and in the metaphysis of human femora reamed under various compression forces. The compression force exerted by the surgeon was measured on polyurethane femora. It was observed that an increase in the compression force of 1.8 times led to an increase in the diaphyseal pressure of 4.7 times and of the metaphyseal pressure of 3.1 times. As surgeons exert high compression forces, peak pressures of 970 mmHg diaphyseally and 1150 mmHg metaphyseally must be expected in the hospital. If reaming is carried out with less compression force, the intramedullary pressure can easily be reduced by 79% in the area of the diaphysis and by 68% in the metaphysis.

Further development of titanium miniplate fixation for mandibular fractures. Experience gained and questions raised from a prospective clinical pilot study with 2.0 mm fixation plates.

Miniplate systems are often used instead of more rigid systems for the treatment of mandibular fractures. While the most stable fixation method for all mandibular fractures is the 2.7 mm plate, most fracture sites and types are eminently suitable for miniplate fixation via an intraoral approach. However, the relatively low stability of the miniplate systems compared with rigid plate systems limits the indications for their use in mandibular fracture treatment, especially when immediate postoperative function is desired. A more rigid miniplate which provides increased stability was studied. The results of a preliminary study and a clinical trial of a 2.0 mm titanium miniplate system are presented in this paper. The therapeutic consequences of the lesser stability afforded by small plate systems are discussed. Indications for miniplate fixation without additional immobilization are reviewed.