Vat Photopolymerization of Reinforced Styrene-Butadiene Elastomers: A Degradable Scaffold Approach.

Vat photopolymerization (VP) is a high-throughput additive manufacturing modality that also offers exceptional feature resolution and surface finish; however, the process is constrained by a limited selection of processable photocurable resins. Low resin viscosity (<10 Pa·s) is one of the most stringent process-induced constraints on resin processability, which in turn limits the mechanical performance of printed resin systems. Recently, the authors created a VP-processable photosensitive latex resin, where compartmentalization of the high molecular weight polymer chains into discrete particles resulted in the decoupling of viscosity from molecular weight. However, the monomers used to form the hydrogel green body resulted in decreased ultimate material properties due to the high cross-link density. Herein, we report a novel scaffold that allows for facile UV-based AM and simultaneously enhances the final part's material properties. This is achieved with a chemically labile acetal-containing cross-linker in conjunction with N-vinylpyrrolidone, which forms a glassy polymer after photocuring. Subsequent reactive extraction cleaves the cross-links and liberates the glassy polymer, which provides mechanical reinforcement of the geometrically complex VP-printed elastomer. With only a 0.1 wt % loading of photoinitiator, G'/G'' crossover times of less than 1 s and green body plateau moduli nearing 105 Pa are obtained. In addition, removal of the hydrophilic and thermally labile scaffold results in decreased water uptake and increased thermal stability of the final printed part. Ultimate strain and stress values of over 650% and 8.5 MPa, respectively, are achieved, setting a new benchmark for styrene-butadiene VP elastomers.

Supramolecular Salts for Additive Manufacturing of Polyimides.

Recent advances in vat photopolymerization (VP) additive manufacturing of fully aromatic polyimides employed photoreactive high-molecular-weight precursors dissolved at modest loadings (<20 wt %) in organic solvent. These earlier efforts revealed high isotropic shrinkage, approaching 52% on a linear basis while converting to the desired polyimide. To increase the polyimide precursor concentration and decrease shrinkage during VP processing of high-performance polyimides, photoreactive fully aromatic polyimide and thermoplastic polyetherimide (PEI) supramolecular salt precursors now serve as versatile alternatives. Both pyromellitic dianhydride-4,4'-oxydianiline (PMDA-ODA) and 4,4'-(4,4'-isopropylidene-diphenoxy)diphthalic anhydride-meta phenylene diamine (BPADA-mPD) supramolecular dicarboxylate-diammonium salts, termed polysalts, provided prerequisite rheological performance and photoreactivity for VP. Solutions (50 wt %) of both photoactive polysalts exhibited viscosities more than two orders of magnitude lower than previously reported polyimide precursor solutions for VP. In addition, VP of 50 wt % polysalt solutions yielded high resolution, self-supporting organogel structures. During thermal postprocessing to the desired fully aromatic polyimide and PEI, photocrosslinked polysalt organogels exhibited retention of part shape in concert with linear isotropic shrinkage of only 26%, the lowest reported value using organogel strategies for VP of fully aromatic polyimides. Furthermore, the imidized structures exhibited comparable thermal and mechanical properties to analogous polyimides synthesized using classical methodologies for 2D films. The combination of facile synthesis and increased precursor concentrations designates polysalt polyimide precursors as a versatile platform for additive manufacturing of well-defined 3D polyimide structures.

3D Printing Latex: A Route to Complex Geometries of High Molecular Weight Polymers.

Vat photopolymerization (VP) additive manufacturing fabricates intricate geometries with excellent resolution; however, high molecular weight polymers are not amenable to VP due to concomitant high solution and melt viscosities. Thus, a challenging paradox arises between printability and mechanical performance. This report describes concurrent photopolymer and VP system design to navigate this paradox with the unprecedented use of polymeric colloids (latexes) that effectively decouple the dependency of viscosity on molecular weight. Photocrosslinking of a continuous-phase scaffold, which surrounds the latex particles, combined with in situ computer-vision print parameter optimization, which compensates for light scattering, enables high-resolution VP of high molecular weight polymer latexes as particle-embedded green bodies. Thermal post-processing promotes coalescence of the dispersed particles throughout the scaffold, forming a semi-interpenetrating polymer network without loss in part resolution. Printing a styrene-butadiene rubber latex, a previously inaccessible elastomer composition for VP, exemplified this approach and yielded printed elastomers with precise geometry and tensile extensibilities exceeding 500%.

3D Printing All-Aromatic Polyimides Using Stereolithographic 3D Printing of Polyamic Acid Salts.

Polyamic acid (PAA) salts are amenable to photocuring additive manufacturing processes of all-aromatic polyimides. Due to an all-aromatic structure, these high-performance polymers are exceptionally chemically and thermally stable but are not conventionally processable in their imidized form. The facile addition of 2-(dimethylamino)ethyl methacrylate (DMAEMA) to commercially available poly(4,4'-oxydiphenylene pyromellitamic acid) (PMDA-ODA PAA) afforded ultraviolet curable PAA salt solutions. These readily prepared solutions do not require multistep synthesis, exhibited fast gel times (<5 s), and rendered high G' gel-state moduli. Vat photopolymerization 3D printing afforded self-supporting organogels. Subsequent thermal treatment rendered the cross-linked PAA precursor to all-aromatic PMDA-ODA polyimide. This fast and facile strategy makes PMDA-ODA polyimides accessible in three dimensions and offers impact on aerospace or automotive technologies.

3D Printing All-Aromatic Polyimides using Mask-Projection Stereolithography: Processing the Nonprocessable.

High-performance, all-aromatic, insoluble, engineering thermoplastic polyimides, such as pyromellitic dianhydride and 4,4'-oxydianiline (PMDA-ODA) (Kapton), exhibit exceptional thermal stability (up to ≈600 °C) and mechanical properties (Young's modulus exceeding 2 GPa). However, their thermal resistance, which is a consequence of the all-aromatic molecular structure, prohibits processing using conventional techniques. Previous reports describe an energy-intensive sintering technique as an alternative technique for processing polyimides with limited resolution and part fidelity. This study demonstrates the unprecedented 3D printing of PMDA-ODA using mask-projection stereolithography, and the preparation of high-resolution 3D structures without sacrificing bulk material properties. Synthesis of a soluble precursor polymer containing photo-crosslinkable acrylate groups enables light-induced, chemical crosslinking for spatial control in the gel state. Postprinting thermal treatment transforms the crosslinked precursor polymer to PMDA-ODA. The dimensional shrinkage is isotropic, and postprocessing preserves geometric integrity. Furthermore, large-area mask-projection scanning stereolithography demonstrates the scalability of 3D structures. These unique high-performance 3D structures offer potential in fields ranging from water filtration and gas separation to automotive and aerospace technologies.