ABSTRACT
Pervious concrete provides a tailored surface course with high permeability properties which permit the easy flow of water through a larger interconnected porous structure to prevent flooding hazards. This paper reports the modeling of the flexural properties of quarry dust (QD) and sawdust ash (SDA) blended green pervious concrete for sustainable road pavement construction using Scheffe's (5,2) optimization approach. The simplex mixture design method was adapted to formulate the mixture proportion to eliminate the set-backs encountered in empirical or trials and the error design approach, which consume more time and resources to design with experimental runs required to evaluate the response function. For the laboratory evaluation exercise, a maximum flexural strength of 3.703 N/mm2 was obtained with a mix proportion of 0.435:0.95:0.1:1.55:0.05 for water, cement, QD, coarse aggregate and SDA, respectively. Moreover, the minimal flexural strength response of 2.504 N/mm2 was obtained with a mix ratio of 0.6:0.75:0.3:4.1:0.25 for water, cement, QD, coarse aggregate and SDA, respectively. The test of the appropriateness of the developed model was statistically verified using the Student' t-test and an analysis of variance (ANOVA), and was confirmed to be acceptable based on computational outcomes at the 95% confidence interval. Furthermore, the scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) were used to evaluate the morphological and mineralogical behavior of green prior concrete samples with various additive mixture compositions. The addition of QD and SDA, on the other hand, aided the creation of porous microstructures in the concrete matrix due to fabric changes in the concrete mixture, potentially aided by the formation of cementitious compounds such as calcium aluminate hydrate and calcium silicate hydrate.
ABSTRACT
Roads play a pivotal role in the overall economic growth of any country. Developed countries allocated sufficient budget to make new roads and to maintain the existing roads. They also have a proper pavement management system (PMS) in practice to manage roads, whereas developing countries suffer from budgetary issues to make new roads and maintain the existing road network. Therefore, this paper explores the awareness of PMS via direct and indirect methods in Pakistan with a proposed framework of the low-cost model and pavement maintenance indicators for developing countries. This paper also performs a scientometric assessment of PMS. A detailed literature review has been carried out for this study, followed by a quantitative study from experienced professionals. The scientometric data is collected from the Scopus database from 1975 to 2020, whereas the data for PMS awareness assessment has been collected using questionnaires from different experts working directly and indirectly in the road management sector. The data has been analyzed using the arithmetic mean because of the nature of the questions and scope of the study. The direct method results show that experts are aware of PMS for a new road, but they have no PMS to rehabilitate roads. The indirect method results show that the authorities are applying various components of PMS, but there is no proper PMS in practice. This paper helps decision-makers to make better decisions and policies for improved road maintenance and rehabilitation. The proposed framework in the study can significantly assist the UN-SDG 9 (Facilitate Sustainable Infrastructure in Developing Countries) and 11 (Affordable and Sustainable Transport System).
Subject(s)
Economic Development , PakistanABSTRACT
The reclaimed asphalt pavement (RAP) has become a moderately common practice in most countries; Hence, rejuvenating materials with RAP have earned publicity in the asphalt manufacturers, mainly due to the increasing raw material costs. In this study, the crumb rubber (CR) and waste frying oil (WFO) utilized as waste materials to restore the properties and enhance the rutting resistance of the RAP. Several physical, rheological, chemical properties of bituminous binders were tested. The result showed that the RAP bituminous binders incorporating WFO and CR decreased softening points and the increased penetration value; these translate to an increase in penetration index. Moreover, the viscosity of the WFO/CR combination reclaimed asphalt pavement binder showed better workability and stiffness, as well as a low storage stability temperature (less than 2.2 °C) with an acceptable loss upon heating. Without chemical reaction was observed between the waste-frying oil with the rubberized binder and the reclaimed asphalt pavement binder. Additionally, the WFO/CR rheological properties combined with the reclaimed asphalt pavement binder were comparable to the control sample. The incorporation of CR with WFO as a hybrid rejuvenator enhanced the rutting resistance. Therefore, the presence of WFO/CR has a considerable influence on the RAP binder properties while preserving a better environment and reducing pollution by reusing waste materials.
ABSTRACT
Polymer modification is extensively used in the Kingdom of Saudi Arabia (KSA) because the available asphalt cement does not satisfy the high-temperature requirements. It was widely used in KSA for more than two decades, and there is little information regarding the differences in the performance of different polymers approved for binder modification. Pavement engineers require performance comparisons among various polymers to select the best polymer for modification rather than make their selection based on satisfying binder specifications. Furthermore, the mechanical properties can help select polymer type, producing mixes of better resistance to specific pavement distresses. The study objective was to compare the mechanical properties of the various polymer-modified asphalt (PMA) mixtures that are widely used in the Riyadh region. Control mix and five other mixes with different polymers (Lucolast 7010, Anglomak 2144, Pavflex140, SBS KTR 401, and EE-2) were prepared. PMA mixtures were evaluated through different mechanical tests, including dynamic modulus, flow number, Hamburg wheel tracking, and indirect tensile strength. The results show an improvement in mechanical properties for all PMA mixtures relative to the control mixture. Based on the overall comparison, the asphalt mixture with polymer Anglomk2144 was ranked the best performing mixture, followed by Paveflex140 and EE-2.
ABSTRACT
Researchers are exploring the utilisation of reclaimed asphalt pavement (RAP) as a recycled material to determine the performance of non-renewable natural aggregates and other road products such as asphalt binder, in the construction and rehabilitation stage of asphalt pavements. The addition of RAP in asphalt mixtures is a complex process and there is a need to understand the design of the asphalt mixture. Some of the problems associated with adding RAP to asphalt mixtures are moisture damage and cracking damage caused by poor adhesion between the aggregates and asphalt binder. There is a need to add rejuvenators to the recycled mixture containing RAP to enhance its performance, excepting the rutting resistance. This study sought to improve asphalt mixture performance and mechanism by adding waste frying oil (WFO) and crumb rubber (CR) to 25 and 40% of the RAP content. Moreover, the utilisation of CR and WFO improved pavement sustainability and rutting performance. In addition, this study prepared five asphalt mixture samples and compared their stiffness, moisture damage and rutting resistance with the virgin asphalt. The results showed enhanced stiffness and rutting resistance of the RAP but lower moisture resistance. The addition of WFO and CR restored the RAP properties and produced rutting resistance, moisture damage and stiffness, which were comparable to the virgin asphalt mixture. All waste and virgin materials produce homogeneous asphalt mixtures, which influence the asphalt mixture performance. The addition of a high amount of WFO and a small amount of CR enhanced pavement sustainability and rutting performance.
