ABSTRACT
We demonstrate foundry-fabricated O-band III-V-on-silicon discrete-mode lasers. The laser fabrication follows the back-side-on-buried-oxide laser integration process and is compatible with complex, multilayer, silicon-on-insulator based platforms. A series of devices were characterized, with the best devices producing on-chip powers of nearly 20 mW with Lorentzian linewidths below 20 kHz and a side mode suppression ratio of at least 60 dB.
ABSTRACT
We demonstrate high-bandwidth O-band Mach-Zehnder modulators with indium phosphide-on-silicon (InP-on-Si) capacitive phase shifters that are compatible with heterogeneous laser fabrication processes. An electro-optic conversion efficiency of 1.3 Vâ cm and a 3 dB bandwidth of up to 30 GHz was observed for a phase modulator length of 250 µm at a 0 V bias. Open eye patterns were observed at up to 25 Gb/s.
ABSTRACT
Silicon nitride-on-silicon bi-layer grating couplers were designed for the O-band using an optimization-based procedure that accounted for design rules and fabricated on a 200 mm wafer. The designs were sufficiently robust to fabrication variations to function well across the wafer. A peak fiber-to-chip coupling efficiency to standard single mode fiber of -2.2 dB and a 1-dB bandwidth of 72.9 nm was achieved in the representative device. Over several chips across the wafer, we measured a median peak coupling efficiency of -2.1 dB and median 1-dB bandwidth of 70.8 nm. The measurements had good correspondence with simulation.
ABSTRACT
We report on the design, fabrication, and characterization of a 1×4 silicon-on-insulator (SOI) demultiplexer exhibiting a significant reduction of its thermo-optical sensitivity in the O-band. The optical filtering is achieved by cascading several Mach-Zehnder interferometers (MZIs) fabricated on a 300-nm-thick SOI platform. Owing to an asymmetric design of the confinement for each MZIs, we found an athermal criterium that satisfies the spectral requirements. The thermal sensitivity of the structure is analyzed by a semi-analytical model in order to create an athermal multiplexer. Fiber-to-fiber thermo-optical testing reveals a thermal sensitivity of around 17 pm/°C reduced by 75% compared to the standard devices with promising performances for both the crosstalk (15 dB), the insertion losses (4 dB), and absolute lambda registration (<0.25 nm).
ABSTRACT
We report on the design, fabrication and performance of a hetero-integrated III-V on silicon distributed feedback lasers (DFB) at 1310 nm based on direct bonding and adiabatic coupling. The continuous wave (CW) regime is achieved up to 55 °C as well as mode-hop-free operation with side-mode suppression ratio (SMSR) above 55 dB. At room temperature, the current threshold is 36 mA and the maximum coupled power in the silicon waveguide is 22 mW.
ABSTRACT
Polarization-diversity couplers, which are designed to couple the unknown polarization state of an optical fiber into the TE-polarized modes of integrated waveguides, are important for the development of practical all-optical circuits. We describe the use of a full 3D finite difference time domain (FDTD) calculation campaign to rigorously optimize the 2D photonic crystal grating that couples a single-mode telecom fiber to the silicon waveguides of a Silicon-on-Insulator (SOI) platform. With this approach we identify the unique optimum combination of etch-depth, hole-radius, and grating-pitch of the photonic crystal array for best performance at 1550 nm. The mean (polarization-averaged) coupling efficiency of 48% (-3.2dB) exceeds reported efficiencies of analogous couplers, and has only a marginal dependence on the polarization state of the input fiber (48 ± 3%). In addition, 3D-FDTD calculations are used to characterize the propagation direction, mode-profile, and polarization of light coupled from the fiber into the SOI slab. Such information is crucial for component design and goes beyond previously available results from existing approximations and simulations of 2D-grating coupler performance. Calculations of photonic mode dispersion in the grating coupler, by means of guided-mode expansion, indicate that the coupling is due to an optically active resonant guided mode in the photonic crystal array. This points towards a fast optimization scheme that enhances both the performance and the physical interpretation of 3D-FDTD simulations.
