ABSTRACT
The present work investigates the effects of severe plastic deformation by cold rolling on the microstructure, the mechanical properties and the corrosion behavior of austenitic stainless steel (SS) 316Ti. Hydroxyapatite coating (HA) was applied on the deformed material to improve their corrosion resistance. The martensitic transformation due to cold rolling was recorded by X-ray diffraction spectra. The effects of cold rolling on the corrosion behavior were studied using potentiodynamic polarization. The electrochemical tests were carried out in Ringer's solution at 37±1 °C. Cold rolling markedly enhanced the mechanical properties while the electrochemical tests referred to a lower corrosion resistance of the deformed material. The best combination of both high strength and good corrosion resistance was achieved after applying hydroxyapatite coating.
Subject(s)
Coated Materials, Biocompatible/chemistry , Durapatite/chemistry , Prostheses and Implants , Stainless Steel/chemistry , Corrosion , Electrochemical Techniques , Hardness , Spectrometry, X-Ray Emission , X-Ray DiffractionABSTRACT
Magnesium alloys are promising materials for biomedical applications because of many outstanding properties like biodegradation, bioactivity and their specific density and Young's modulus are closer to bone than the commonly used metallic implant materials. Unfortunately their fatigue properties and low corrosion resistance negatively influenced their application possibilities in the field of biomedicine. These problems could be diminished through appropriate surface treatments. This study evaluates the influence of a surface pre-treatment by shot peening and shot peening+coating on the corrosion properties of magnesium alloy AZ31. The dicalcium phosphate dihydrate coating (DCPD) was electrochemically deposited in a solution containing 0.1M Ca(NO3)2, 0.06M NH4H2PO4 and 10mL/L of H2O2. The effect of shot peening on the surface properties of magnesium alloy was evaluated by microhardness and surface roughness measurements. The influence of the shot peening and dicalcium phosphate dihydrate layer on the electrochemical characteristics of AZ31 magnesium alloy was evaluated by potentiodynamic measurements and electrochemical impedance spectroscopy in 0.9% NaCl solution at a temperature of 22±1°C. The obtained results were analyzed by the Tafel-extrapolation method and equivalent circuit method. The results showed that the application of shot peening process followed by DCPD coating improves the properties of the AZ31 surface from corrosion and mechanical point of view.
Subject(s)
Coated Materials, Biocompatible/chemistry , Metal Nanoparticles/chemistry , Alloys/chemistry , Biodegradation, Environmental , Calcium Phosphates/chemistry , Corrosion , Dielectric Spectroscopy , Hydrogen Peroxide , Magnesium/chemistry , Particle Size , Sodium Chloride/chemistry , Solutions/chemistry , Surface Properties , TemperatureABSTRACT
A novel approach of surface treatment of orthopaedic implants combining electric discharge machining (EDM), chemical milling (etching) and shot peening is presented in this study. Each of the three techniques have been used or proposed to be used as a favourable surface treatment of biomedical titanium alloys. But to our knowledge, the three techniques have not yet been used in combination. Surface morphology and chemistry were studied by scanning electron microscopy and X-ray photoelectron spectroscopy, respectively. Fatigue life of the material was determined and finally several in-vitro biocompatibility tests have been performed. EDM and subsequent chemical milling leads to a significant improvement of osteoblast proliferation and viability thanks to favourable surface morphology and increased oxygen content on the surface. Subsequent shot-peening significantly improves the fatigue endurance of the material. Material after proposed combined surface treatment possesses favourable mechanical properties and enhanced osteoblast proliferation. EDM treatment and EDM with shot peening also supported early osteogenic cell differentiation, manifested by a higher expression of collagen type I. The combined surface treatment is therefore promising for a range of applications in orthopaedics.
Subject(s)
Cell Proliferation/drug effects , Osteoblasts/drug effects , Titanium/chemistry , Alloys , Biocompatible Materials/chemistry , Cell Adhesion/drug effects , Cell Differentiation/drug effects , Cell Line, Tumor , Cell Survival/drug effects , Fluorescent Antibody Technique , Humans , Microscopy, Electron, Scanning , Osteoblasts/cytology , Photoelectron Spectroscopy , Prostheses and Implants , Surface Properties , Titanium/pharmacologyABSTRACT
Magnesium alloys suffer from their high reactivity in common environments. Protective layers are widely created on the surface of magnesium alloys to improve their corrosion resistance. This article evaluates the influence of a calcium-phosphate layer on the electrochemical characteristics of AZ31 magnesium alloy in 0.9 % NaCl solution. The calcium phosphate (CaP) layer was electrochemically deposited in a solution containing 0.1 M Ca(NO3)2, 0.06 M NH4H2PO4 and 10 ml l(-1) of H2O2. The formed surface layer was composed mainly of brushite [(dicalcium phosphate dihidrate (DCPD)] as proved by energy-dispersive X-ray analysis. The surface morphology was observed by scanning electron microscopy. Immersion test was performed in order to observe degradation of the calcium phosphatized surfaces. The influence of the phosphate layer on the electrochemical characteristics of AZ31, in 0.9 % NaCl solution, was evaluated by potentiodynamic measurements and electrochemical impedance spectroscopy. The obtained results were analysed by the Tafel-extrapolation method and equivalent circuits method. The results showed that the polarization resistance of the DCPD-coated surface is about 25 times higher than that of non-coated surface. The CaP electro-deposition process increased the activation energy of corrosion process.
