Ionic Liquids in Metal, Photo-, Electro-, and (Bio) Catalysis.

Ionic liquids (ILs) have unique physicochemical properties that make them advantageous for catalysis, such as low vapor pressure, non-flammability, high thermal and chemical stabilities, and the ability to enhance the activity and stability of (bio)catalysts. ILs can improve the efficiency, selectivity, and sustainability of bio(transformations) by acting as activators of enzymes, selectively dissolving substrates and products, and reducing toxicity. They can also be recycled and reused multiple times without losing their effectiveness. ILs based on imidazolium cation are preferred for structural organization aspects, with a semiorganized layer surrounding the catalyst. ILs act as a container, providing a confined space that allows modulation of electronic and geometric effects, miscibility of reactants and products, and residence time of species. ILs can stabilize ionic and radical species and control the catalytic activity of dynamic processes. Supported IL phase (SILP) derivatives and polymeric ILs (PILs) are good options for molecular engineering of greener catalytic processes. The major factors governing metal, photo-, electro-, and biocatalysts in ILs are discussed in detail based on the vast literature available over the past two and a half decades. Catalytic reactions, ranging from hydrogenation and cross-coupling to oxidations, promoted by homogeneous and heterogeneous catalysts in both single and multiphase conditions, are extensively reviewed and discussed considering the knowledge accumulated until now.

Zwitterionic "Solutions" for Reversible CO2 Capture.

The zwitterions resulting from the covalent attachment of 3- or 4-hydroxy benzene to the 1,3-dimethylimidazolium cation represent basic compounds (pKa of 8.68 and 8.99 in aqueous solutions, respectively) that chemisorb in aqueous solutions 0.58 mol/mol of carbon dioxide at 1.3 bar (absolute) and 40 °C. Equimolar amounts of chemisorbed CO2 in these solutions are obtained at 10 bar and 40 °C. Chemisorption takes place through the formation of bicarbonate in the aqueous solution using imidazolium-containing phenolate. CO2 is liberated by simple pressure relief and heating, regenerating the base. The enthalpy of absorption was estimated to be -38 kJ/mol, which is about 30 % lower than the enthalpy of industrially employed aqueous solutions of MDEA (estimated at -53 kJ/mol using the same experimental apparatus). The physisorption of CO2 becomes relevant at higher pressures (>10 bar) in these aqueous solutions. Combined physio- and chemisorption of up to 1.3 mol/mol at 40 bar and 40 °C can be attained with these aqueous zwitterionic solutions that are thermally stable and can be recycled at least 20 times.

Templated Growth of Pd Nanoparticles Using Sputtering Deposition Process and Its Catalytic Activities.

A simple method based on sputtering deposition of Pd onto mesoporous SiO2 (SBA-15) was employed to produce supported Pd nanoparticles (NPs) that can be used as hydrogenation catalysts. The use of sputtering deposition eliminates contaminants and avoids additional drawbacks of traditional chemical methods applied to prepare heterogeneous supported metal catalysts. A mechanical resonant stirrer was used to revolve the SBA-15 powder and ensure homogeneous distribution of the Pd NPs over the support. The SBA-15 pores act as templates for Pd NPs and drive nanostructure growth. Consequently, the NPs obtained have the same diameter as that of the SBA-15 channels (~5 nm) and elongated particles are formed as sputtering deposition increases. The SBA-15 supported Pd NPs (Pd NPs/SBA-15) were tested in a probe hydrogenation of cyclohexene reaction to evaluate the catalytic activity of the Pd NPs. Turnover frequency (TOF) of 2000 min-1 were achieved with the lower Pd NPs concentration (0.15 wt%) catalyst.

Confined naked gold nanoparticles in ionic liquid films.

Surface-clean Au nanoparticles (NPs) confined in films of ionic liquids (ILs) can be easily fabricated by sputtering deposition. A silicon wafer coated with films of both hydrophobic (bis((trifluoromethyl)sulfonyl)amide, NTf2-) and hydrophilic (tetrafluoroborate, BF4-) imidazolium-based ILs forms an 'ionic carpet-like' structure that can be easily decorated with Au NPs of 5.1 and 6.5 nm mean diameter, respectively. The depth profile distribution of the Au NPs depends on the arrangement of the IL, which is controlled mainly by the anion volume. Higher concentrations of Au NPs are found closer to the IL surface for the system containing a larger anion (NTf2) whereas Au NPs are located deeper in the IL for the system containing a smaller anion (BF4). The Au NPs are well distributed over the IL/Si support and are strictly confined in a single layer of the IL. This method is among the most simple and versatile for the generation of liquid layers containing surface-clean, stable and confined Au NPs.

Synergistic Interaction within Bifunctional Ruthenium Nanoparticle/SILP Catalysts for the Selective Hydrodeoxygenation of Phenols.

Ruthenium nanoparticles immobilized on acid-functionalized supported ionic liquid phases (Ru NPs@SILPs) act as efficient bifunctional catalysts in the hydrodeoxygenation of phenolic substrates under batch and continuous flow conditions. A synergistic interaction between the metal sites and acid groups within the bifunctional catalyst leads to enhanced catalytic activities for the overall transformation as compared to the individual steps catalyzed by the separate catalytic functionalities.

Anion-π and halide-halide nonbonding interactions in a new ionic liquid based on imidazolium cation with three-dimensional magnetic ordering in the solid state.

We present the first magnetic phase of an ionic liquid with anion-π interactions, which displays a three-dimensional (3D) magnetic ordering below the Néel temperature, TN = 7.7 K. In this material, called Dimim[FeBr4], an exhaustive and systematic study involving structural and physical characterization (synchrotron X-ray, neutron powder diffraction, direct current and alternating current magnetic susceptibility, magnetization, heat capacity, Raman and Mössbauer measurements) as well as first-principles analysis (density functional theory (DFT) simulation) was performed. The crystal structure, solved by Patterson-function direct methods, reveals a monoclinic phase (P21 symmetry) at room temperature with a = 6.745(3) Å, b = 14.364(3) Å, c = 6.759(3) Å, and ß = 90.80(2)°. Its framework, projected along the b direction, is characterized by layers of cations [Dimim](+) and anions [FeBr4](-) that change the orientation from layer to layer, with Fe···Fe distances larger than 6.7 Å. Magnetization measurements show the presence of 3D antiferromagnetic ordering below TN with the existence of a noticeable magneto-crystalline anisotropy. From low-temperature neutron diffraction data, it can be observed that the existence of antiferromagnetic order is originated by the antiparallel ordering of ferromagnetic layers of [FeBr4](-) metal complex along the b direction. The magnetic unit cell is the same as the chemical one, and the magnetic moments are aligned along the c direction. The DFT calculations reflect the fact that the spin density of the iron ions spreads over the bromine atoms. In addition, the projected density of states (PDOS) of the imidazolium with the bromines of a [FeBr4](-) metal complex confirms the existence of the anion-π interaction. Magneto-structural correlations give no evidence for direct iron-iron interactions, corroborating that the 3D magnetic ordering takes place via superexchange coupling, the Fe-Br···Br-Fe interplane interaction being defined as the main exchange pathway.

TiO2 nanotubes sensitized with CdSe via RF magnetron sputtering for photoelectrochemical applications under visible light irradiation.

Highly ordered TiO2 NT arrays were easily decorated with CdSe via RF magnetron sputtering. After deposition thermal annealing at different temperatures was performed to obtain an improved TiO2/CdSe interface. The heterostructures were characterized by RBS, SEM, XRD, HRTEM, UV-Vis, EIS, IPCE and current versus voltage curves. The sensitized semiconducting electrodes display an enhanced photocurrent density of ca. 2 mA cm(-2) at 0.6 V (vs. Ag/AgCl) under visible light (λ > 400 nm). The sensitized photoelectrodes displayed 3 and 535-fold enhanced photocurrent when compared to bare TiO2 NTs under 1 sun and under visible light illumination, respectively. IES results confirmed the improved charge transfer across the TiO2/CdSe/electrolyte interface after annealing at 400 °C. Incident photon-to-electron conversion efficiency measurements confirmed the efficient sensitization by allowing photoresponse in the visible range.

A magnetic ionic liquid based on tetrachloroferrate exhibits three-dimensional magnetic ordering: a combined experimental and theoretical study of the magnetic interaction mechanism.

A new magnetic ionic liquid (MIL) with 3D antiferromagnetic ordering has been synthetized and characterized. The information obtained from magnetic characterization was supplemented by analysis of DFT calculations and the magneto-structural correlations. The result gives no evidence for direct iron-iron interactions, corroborating that the 3D magnetic ordering in MILs takes place via super-exchange coupling containing two diamagnetic atoms intermediaries.

Controlled synthesis of Mn3O4 nanoparticles in ionic liquids.

This work describes a simple one-step synthesis of Mn3O4 nanoparticles by thermal decomposition of [Mn(acac)2] (acac = acetylacetonate) using imidazolium ionic liquids (ILs) and a conventional solvent, oleylamine, for comparison. The Mn3O4 nanoparticles were characterized by XRD, ATR-FTIR, TEM, Raman, UV/VIS and magnetometry techniques. The addition of 1-n-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide IL (BMI·NTf2) yielded a smaller particle size (9.9 ± 1.8 nm) with better dispersion and more regular sizes than synthesis using oleylamine as the solvent (12.1 ± 3.0 nm). The complete conversion of the precursor to Mn3O4 nanoparticles occurred after 96 h at 180 °C for the reaction performed in BMI·NTf2. However, under these reaction conditions in oleylamine, no precursor was detected, but two different phases were observed: a major phase corresponding to Mn3O4 and a minor phase corresponding to MnO2. Magnetometry revealed that Mn3O4 nanoparticles synthesized in either oleylamine or BMI·NTf2 exhibited ferrimagnetic behavior at low temperatures, whereas they were paramagnetic at room temperature. As expected, the blocking temperature and the coercivity decreased with the size of nanoparticles. Our results demonstrate that reaction conditions such as time, and the nature of the ionic liquid play important roles in determining the size of Mn3O4 nanoparticles.

Sputtering deposition of magnetic Ni nanoparticles directly onto an enzyme surface: a novel method to obtain a magnetic biocatalyst.

A simple one-step method based on the sputtering deposition of Ni nanoparticles (NP) has been developed for the production of magnetic biocatalysts, avoiding the complications and drawbacks of methods based on chemical functionalisation or coating of magnetic NP. This new technique provided high levels of recovery, reusability and catalytic activity for the lipase-Ni biocatalyst.

On the formation of anisotropic gold nanoparticles by sputtering onto a nitrile functionalised ionic liquid.

Sputtering deposition of gold onto the 1-(butyronitrile)-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (BCN)MI·N(Tf)(2) ionic liquid (IL) has generated colloidal and stable gold nanospheres (AuNS) and gold nanodisks (AuND) in a bimodal size distribution. Upon increasing the sputtering discharge voltage, three distinct phenomena were observed: (i) the mean diameter of both AuNS and AuND decreased; (ii) the population with lower diameters increased and (iii) the formation of AuND disappeared at voltages higher than 340 V. By dissolving the colloidal gold nanoparticles (AuNPs) in isopropanol and dropping the product onto carbon-coated Cu grids, 2D and 3D superlattices tended to be formed, as observed by transmission electron microscopy (TEM). Therefore, the formation of AuND is probably related to a strong interaction between sputtered Au atoms of low kinetic energy and the nitrile groups orientated to the vacuum phase of the IL surface, which drives the preferential anisotropic lateral growth.

From alumina nanopores to nanotubes: dependence on the geometry of anodization system.

The Conventional anodization of commercial aluminum sheets with a phosphoric acid electrolyte was employed for the preparation of alumina nanopore and/or nanotube structures. Modifying the system geometry (the ratio of platinum to aluminum electrode areas) controlled the nature of the anodization process (mild to hard). Nanotube formation was observed after low temperature preferential chemical etching of the defective corners of the hexagonal alumina cells using the same solution from the anodization process. Electrode geometry can be used to combine mild and hard anodization with low temperature etching to tune the alumina morphology from 100% nanopores to 100% nanotubos coverage.

Structural control of gold nanoparticles self-assemblies by layer-by-layer process.

This work presents a novel way to introduce gold nanoparticles (Au NPs) in a multilayer polymer produced by the layer-by-layer (LbL) assembling technique. The technique chosen shows that, depending on the pH used, different morphological structures can be obtained from monolayer or bilayer Au NPs. The MEIS and RBS techniques allowed for the modelling of the interface polymer-NPs, as well as the understanding of the interaction of LbL system, when adjusting the pH in weak polyelectrolytes. The process reveals that the optical properties of multilayer systems could be fine-tuned by controlling the addition of metallic nanoparticles, which could also modify specific polarization responses.

Self-organized TiO2 nanotube arrays: synthesis by anodization in an ionic liquid and assessment of photocatalytic properties.

Self-organized TiO(2) nanotube (NT) arrays were produced by anodization in ethylene glycol (EG) electrolytes containing 1-n-butyl-3-methyl-imidazolium tetrafluoroborate (BMI.BF(4)) ionic liquid and water. The morphology of the as-formed NTs was considerably affected by changing the anodization time, voltage, and water and ionic liquid electrolyte concentrations. In general, a nanoporous layer was formed on the top surface of the TiO(2) NTs, except for anodization at 100 V with 1 vol % of BMI.BF(4), where the NT's mouth was revealed. The length and bottom diameter of the NTs as well as the pore diameter of the top layer showed a linear relationship with increased anodization voltage. These TiO(2) NTs were tested as photocatalysts for methyl orange photodegradation and hydrogen evolution from water/methanol solutions by UV light irradiation. The results show that the TiO(2) NTs obtained by anodization in EG/H(2)O/BMI.BF(4) electrolytes are active and efficient for both applications.

Synthesis of gold nanoparticles in a biocompatible fluid from sputtering deposition onto castor oil.

The sputtering of Au targets onto castor oil generates stable spherical gold nanoparticles (AuNPs) of 2.4 to 3.8 nm. The AuNP size increases with the discharge voltage and the mechanism of nucleation and growth are related to the energy of the atoms/clusters ejected from the target.

Nanostructures in ionic liquids: correlation of iridium nanoparticles' size and shape with imidazolium salts' structural organization and catalytic properties.

Hydrogen reduction of cationic or neutral Ir(i) compounds, namely [Ir(COD)(2)]BF(4) and [Ir(COD)Cl](2)respectively. in the ionic liquid (IL) 1-alkyl-3-methylimidazolium tetrafluoroborate affords either irregularly sized spherical (from 1.9 +/- 0.4 to 3.6 +/- 0.9 nm) or worm-like metal nanoparticles, depending on the nature of the imidazolium alkyl group and the type of iridium precursor. The ionic Ir(i) precursor tends to be dissolved and concentrated on the IL polar domains (populated by the imidazolium nucleus and tetrafluoroborate anions) while the neutral precursor dissolves preferentially in the non-polar region of the IL (populated mainly by N-alkyl side chains). The size, or volume, of the nano-region where the Ir(i) precursor is dissolved and reduced, determines the size and, probably, the shape of the formed nanoparticles. The HR-TEM image shows that the Ir(0) with worm-like shape are polycrystalline and formed from aggregation individual "spherical" nanoparticles of around 1.9 nm. The catalytic activity of Ir(0) NPs on the hydrogenation of cyclohexene (0.01 mol L(-1) of Ir atoms in IL, 75 degrees C, 8 bar of H(2), 500 rpm stirring, 1/1000 Ir(0)/cyclohexene ratio) is always greater in C(1)C(10)I.BF(4) than C(1)C(4)I.BF(4), regardless of the nature of Ir(i) precursor. Moreover, the cyclohexene hydrogenations performed with Ir(0) nanocatalysts made from ionic Ir(i) precursor are approximately twice faster than those NPs obtained from the neutral Ir(i) precursor, in the same IL.

Biosensor for chlorogenic acid based on an ionic liquid containing iridium nanoparticles and polyphenol oxidase.

A biosensor based on the ionic liquid, 1-n-butyl-3-methylimidazolium hexafluorophosphate containing dispersed iridium nanoparticles (Ir-BMI.PF(6)) and polyphenol oxidase was constructed. This enzyme was obtained from the sugar apple (Annona squamosa), immobilized in chitosan ionically crosslinked with oxalate. The biosensor was used for determination of chlorogenic acid by square wave voltammetry. The polyphenol oxidase catalyzes the oxidation of chlorogenic acid to the corresponding o-quinone, which is electrochemically reduced back to this substance at +0.25V vs. Ag/AgCl. Under optimized operational conditions the chlorogenic acid concentration was linear in the range of 3.48x10(-6) to 4.95x10(-5)mol L(-1) with a detection limit of 9.15x10(-7)mol L(-1). The biosensor was applied in the determination of chlorogenic acid in organic and decaffeinated coffee and the results compared with those obtained using the capillary electrophoresis method. The recovery study for chlorogenic acid in these samples gave values of 93.2-105.7%.

Development of biosensors containing laccase and imidazolium bis(trifluoromethylsulfonyl)imide ionic liquid for the determination of rutin.

Biosensors based on hydrophobic ionic liquids (ILs) derived from the bis(trifluoromethylsulfonyl)imide [(CF(3)SO(2))(2)N(-) = Tf(2)N(-)] anion associated with three different imidazolium cations: 1-butyl-3-methylimidazolium (BMI x Tf(2)N), 1-decyl-3-methylimidazolium (DMI x Tf(2)N) and 1-tetradecyl-3-methylimidazolium (TDMI x Tf(2)N), along with laccase from Aspergillus oryzae, were constructed and optimized for determination of rutin. The laccase catalyzes the oxidation of rutin to the corresponding o-quinone, which is electrochemically reduced back to rutin. The best performance was obtained with 50:20:15:15% (w/w/w/w) as the graphite powder:laccase:Nujol:ILs composition in 0.1 mol L(-1) acetate buffer solution (pH 5.0). The parameters for the square-wave voltammetry experiments and scanning electron microscopy images of the biosensors were studied. Under the selected conditions, the cathodic peak current increased linearly in the rutin concentration ranges of 4.77x10(-6) to 4.62x10(-5) mol L(-1), 5.84x10(-6) to 5.36x10(-5) mol L(-1) and 5.84x10(-6) to 5.36x10(-5) mol L(-1) using the (I) BMI x Tf(2)N-laccase, (II) DMI x Tf(2)N-laccase and (III) TDMI x Tf(2)N-laccase, respectively. The rutin contents of commercial samples of pharmaceuticals were successfully determined by the biosensors and the results compared well with those obtained using the official method. The studies on rutin recovery from these samples gave values of 96.9-104.6%.

Synthesis and characterization of nickel nanoparticles dispersed in imidazolium ionic liquids.

The diameter and size-distribution of Ni nanoparticles prepared by the decomposition of [bis(1,5-cyclooctadiene)nickel(0)] organometallic precursor dissolved in 1-alkyl-3-methylimidazolium N-bis(trifluoromethanesulfonyl) amide ionic liquids depend on the length of the alkyl side-chain of the imidazolium ring. The increase of the organization range order of the ionic liquid that increases with that of the alkyl side-chain (from n-butyl to n-hexadecyl) induces the formation of nanoparticles with a smaller diameter and size-distribution. The cubic fcc Ni nanoparticles with 4.9 +/- 0.9 to 5.9 +/- 1.4 nm in mean diameter and monomodal size-distribution thus prepared are probably composed of a small cap layer of NiO around a core of Ni metal. The contribution of the oxide layer also depends on the medium i.e. the metal oxide ratio increases in salts containing four to eight carbons on their side-chains and then decreases as the number of carbons increases. The Ni nanoparticles dispersed in the ionic liquids are active catalysts for the hydrogenation of olefins under relatively mild reaction conditions.

Catalytic applications of metal nanoparticles in imidazolium ionic liquids.

Metal nanoparticles (MNPs) with a small diameter and narrow size distribution can be prepared by H(2) reduction of metal compounds or decomposition of organometallic species dissolved in ionic liquids (ILs). MNPs dispersed in ILs are catalysts for reactions under multiphase conditions. These soluble MNPs possess a pronounced surfacelike rather than single-site like catalytic properties. In other cases the MNPs are not stable and tend to aggregate or serve as reservoirs of mononuclear catalytically active species.