Connectivity approach in urban protected area management based on soil and vegetation chemical status.

The quality and vitality of cities largely depend on the design, management, and maintenance of green areas, including urban protected areas (UPAs), since they provide multiple benefits for the city. Due to urbanization and higher anthropogenic pressure, green areas are decreasing which directly affects natural habitats and biodiversity. This study aims to assess soil and vegetation chemical status in UPAs in the city of Belgrade, Serbia, and to understand how their distance from pollution hotspots affects soil and vegetation quality. Additionally, this paper considers the inclusion of soil and vegetation conditions in the urban protected areas management as a basis for introducing a connectivity approach to expand green infrastructure throughout the city. Chemical properties, the content of nutrients (C, N, P, and K), and microelements (Cr, Co, Ni, Cu, Zn, As, Cd, Sn, Pb, Zr, U, and Th) in soil and conifer needles were analyzed. Results showed that the distance of pollution hotspots does not affect nutrient and microelements concentrations in soil, i.e., they do not vary significantly between sites and do not exceed remediation intervention values. However, the microelements status of vegetation is affected since Cr, Cu, Zn, Sn, and Pb are higher in needles from trees from the city center. The state of soil and plant composition supports the establishment of a network of green corridors and should become a part of management strategies, thus helping biodiversity protection, climate change mitigation, and human well-being in the cities.

Fired pressed pellet as a sample preparation technique of choice for an energy dispersive X-ray fluorescence analysis of raw clays.

In this paper, the main subject concerns comparing different techniques to prepare raw clay samples for energy-dispersive X-ray fluorescence spectrometry (EDXRF). Three kinds of sample preparation procedures are examined, such as loose powder, pressed pellet, and fired pressed pellet. The fired pressed pellet approach was observed as a part of universal sample preparation for physic, mechanical, and instrumental analysis, which has not been previously tested as a solution in chemical analysis by the EDXRF method. The observed sample preparation techniques were compared by calculating the parameters of validation (recoveries, limit of detection - LOD, limit of quantification - LOQ, precision, and expanded uncertainties of measurements) of 11 elements (Si, Al, Fe, Ca, Mg, K, Na, Ti, P, Mn, and S) using 15 certified reference materials (CRMs). Calibration curves were created and evaluated using 30 reference materials (RM) for all three approaches. Results proved that the fired pressed pellet is the most practical and precise approach for sample preparation of raw clays.

Aplitic Granite Waste as Raw Material for the Production of Outdoor Ceramic Floor Tiles.

One of the significant problems in the production of ceramic tiles is the very high consumption of natural resources such as clay, feldspar, and quartz. The possibility of replacing part of the formulation of ceramic batches is of great importance. In this research, the possibility of using aplitic granite waste from dimensional stone production was analyzed in detail. The waste is considered a low-cost substitute for feldspar in Serbia. The milled powdery waste was analytically tested to reveal its chemical and mineralogical contents, particle size distribution, and other important properties. The ceramic tiles containing aplitic granite waste (GW) and GW/raw clay mixture (CGW) were hydraulically pressed, and the ceramic and technological properties determined. This waste can act as a filler while forming, drying, and firing, since the high content of quartz helps to control the shrinkage and acts as a fluxing agent in high temperatures due to its feldspathic nature. The waste was found favorable in the production of ceramic tiles, as the gained values of modulus of rupture and water absorption were 28.68 MPa and 1.33%, respectively. The parameters defined in the series of standards EN ISO 10545 were tested on a semi-industrial probe, determining that this combination of materials (without the addition of quartz) may be efficiently used to produce ceramic floor tiles. The usage of what would otherwise be waste material contributes to sustainable management and environmentally friendly solutions by avoiding landfilling, while at the same time it enabling the conservation of scarce natural feldspar deposits.

The characterization and pollution status of the surface sediment in the Boka Kotorska Bay, Montenegro.

Surface sediments collected from twelve stations in the Boka Kotorska Bay were analyzed for the level and distribution of twenty-six elements and ten oxides, grain sizes, organic matter, and carbonate content. Potentially toxic elements (Al, Fe, Mn, Cr, Zn, Ni, Cu, Pb, As, Co, U) were determined to assess the contamination status and potential environmental risk according to the single-element indices (enrichment factor (EF), geoaccumulation index (Igeo), contamination factor (CF)), and combined index (pollution load index (PLI)). The single-element indices EF and CF revealed that the surface marine sediment was moderately polluted with Pb, Cu, and Cr, while Igeo indicated moderate pollution with Ni > Cr > Zn > Cu > As and moderate to heavy pollution with Pb, as a result of the anthropogenic factors. The method of the combined effect of toxic elements, PLI, showed the highest pollution rate at the shipyard location in the Bay of Tivat. Pearson's correlation coefficient (r), principal component analysis (PCA), and cluster analysis (CA) were applied to highlight similarities and differences in the distribution of the investigated elements in the Bay, confirming the claim obtained by the pollution indices. The sediment contamination with most heavy metals, such as Cr, Zn, Ni, Cu, Pb, and As, has been identified in the Tivat Bay area.