Rewritable Photonic Integrated Circuit Canvas Based on Low-Loss Phase Change Material and Nanosecond Pulsed Lasers.

Programmable photonic integrated circuits (PICs) are an increasingly important platform in optical science and engineering. However, current programmable PICs are mostly formed through subtractive fabrication techniques, which limits the reconfigurability of the device and makes prototyping costly and time-consuming. A rewritable PIC architecture can circumvent these drawbacks, where PICs are repeatedly written and erased on a single PIC canvas. We demonstrate such a rewritable PIC platform by selective laser writing a layer of wide-band-gap phase change material (PCM) Sb2S3 with a low-cost benchtop setup. We show arbitrary patterning with resolution up to 300 nm and write dielectric assisted waveguides with a low optical loss of 0.0172 dB/µm. We envision that using this inexpensive benchtop platform thousands of PIC designs can be written, tested, and erased on the same chip without the need for lithography/etching tools or a nanofabrication facility, thus reducing manufacturing cost and increasing accessibility.

Nonvolatile Phase-Only Transmissive Spatial Light Modulator with Electrical Addressability of Individual Pixels.

Active metasurfaces with tunable subwavelength-scale nanoscatterers are promising platforms for high-performance spatial light modulators (SLMs). Among the tuning methods, phase-change materials (PCMs) are attractive because of their nonvolatile, threshold-driven, and drastic optical modulation, rendering zero-static power, crosstalk immunity, and compact pixels. However, current electrically controlled PCM-based metasurfaces are limited to global amplitude modulation, which is insufficient for SLMs. Here, an individual-pixel addressable, transmissive metasurface is experimentally demonstrated using the low-loss PCM Sb2Se3 and doped silicon nanowire heaters. The nanowires simultaneously form a diatomic metasurface, supporting a high-quality-factor (∼406) quasi-bound-state-in-the-continuum mode. A global phase-only modulation of ∼0.25π (∼0.2π) in simulation (experiment) is achieved, showing ten times enhancement. A 2π phase shift is further obtained using a guided-mode resonance with enhanced light-Sb2Se3 interaction. Finally, individual-pixel addressability and SLM functionality are demonstrated through deterministic multilevel switching (ten levels) and tunable far-field beam shaping. Our work presents zero-static power transmissive phase-only SLMs, enabled by electrically controlled low-loss PCMs and individual meta-molecule addressable metasurfaces.

Non-volatile electrically programmable integrated photonics with a 5-bit operation.

Scalable programmable photonic integrated circuits (PICs) can potentially transform the current state of classical and quantum optical information processing. However, traditional means of programming, including thermo-optic, free carrier dispersion, and Pockels effect result in either large device footprints or high static energy consumptions, significantly limiting their scalability. While chalcogenide-based non-volatile phase-change materials (PCMs) could mitigate these problems thanks to their strong index modulation and zero static power consumption, they often suffer from large absorptive loss, low cyclability, and lack of multilevel operation. Here, we report a wide-bandgap PCM antimony sulfide (Sb2S3)-clad silicon photonic platform simultaneously achieving low loss (<1.0 dB), high extinction ratio (>10 dB), high cyclability (>1600 switching events), and 5-bit operation. These Sb2S3-based devices are programmed via on-chip silicon PIN diode heaters within sub-ms timescale, with a programming energy density of [Formula: see text]. Remarkably, Sb2S3 is programmed into fine intermediate states by applying multiple identical pulses, providing controllable multilevel operations. Through dynamic pulse control, we achieve 5-bit (32 levels) operations, rendering 0.50 ± 0.16 dB per step. Using this multilevel behavior, we further trim random phase error in a balanced Mach-Zehnder interferometer.

Rewritable photonic integrated circuits using dielectric-assisted phase-change material waveguides.

Photonic integrated circuits (PICs) can drastically expand the capabilities of quantum and classical optical information science and engineering. PICs are commonly fabricated using selective material etching, a subtractive process. Thus, the chip's functionality cannot be substantially altered once fabricated. Here, we propose to exploit wide-bandgap non-volatile phase-change materials (PCMs) to create rewritable PICs. A PCM-based PIC can be written using a nanosecond pulsed laser without removing any material, akin to rewritable compact disks. The whole circuit can then be erased by heating, and a new circuit can be rewritten. We designed a dielectric-assisted PCM waveguide consisting of a thick dielectric layer on top of a thin layer of wide-bandgap PCMs Sb2S3 and Sb2Se3. The low-loss PCMs and our designed waveguides lead to negligible optical loss. Furthermore, we analyzed the spatiotemporal laser pulse shape to write the PICs. Our proposed platform will enable low-cost manufacturing and have a far-reaching impact on the rapid prototyping of PICs, validation of new designs, and photonic education.

Early-life seizures produce lasting alterations in the structure and function of the prefrontal cortex.

Early-life seizures (ELS) are associated with long-term behavioral disorders including autism and ADHD, suggesting that frontal lobe structures may be permanently affected. We tested whether ELS produce structural alterations in the prefrontal cortex (PFC) and impair PFC-mediated function using an operant task of behavioral flexibility in rats. Adult rats that had been exposed to 75 flurothyl seizures during postnatal days 1-10 showed decreased behavioral flexibility in the task compared to controls over multiple behavioral sessions, measured as a lever preference asymmetry (p<0.001) and a decreased efficiency of attaining food rewards (p<0.05). ELS rats also showed an increased thickness of the PFC (p<0.01), primarily attributed to layer V (p<0.01) with no differences in cell density. These structural changes correlated with lever preference behavioral impairments (p<0.05). This study demonstrates that the consequences of ELS extend to the PFC, which may help explain the high prevalence of comorbid behavioral disorders following ELS.

Interictal spikes in developing rats cause long-standing cognitive deficits.

Frequent interictal spikes are a common finding in the electroencephalograms of children with epileptic encephalopathies. While it is well recognized that interictal spikes are a biological marker of seizures and can lead to transitory cognitive impairment, whether interictal spikes can result in long-standing adverse effects on learning and memory in children is not known. Here we investigated the consequences of interictal spikes in rat pups without seizures on long-term learning and memory. Rat pups were given a low dose of flurothyl for 4h for 10 days during continuous electroencephalographic monitoring. Rats developed interictal spikes without seizures while age-matched controls under similar testing conditions had few interictal spikes. When rats were tested as adults, there was impairment in reference memory in the probe test of the Morris water maze, reference memory impairment in the four-trial radial-arm water maze and impaired long-term potentiation. Early-life interictal spikes resulted in impaired new cell formation and decreased cell counts in the hippocampus but did not cause an increase in apoptosis. This study, for the first time demonstrates that interictal spikes in rat pups without seizures can result in long-standing spatial cognitive impairment. Our findings suggest that suppressing IIS may be as important as treating seizures during brain development.

Fracture toughness and fatigue crack propagation rate of short fiber reinforced epoxy composites for analogue cortical bone.

Third-generation mechanical analogue bone models and synthetic analogue cortical bone materials manufactured by Pacific Research Laboratories, Inc. (PRL) are popular tools for use in mechanical testing of various orthopedic implants and biomaterials. A major issue with these models is that the current third-generation epoxy-short fiberglass based composite used as the cortical bone substitute is prone to crack formation and failure in fatigue or repeated quasistatic loading of the model. The purpose of the present study was to compare the tensile and fracture mechanics properties of the current baseline (established PRL "third-generation" E-glass-fiber-epoxy) composite analogue for cortical bone to a new composite material formulation proposed for use as an enhanced fourth-generation cortical bone analogue material. Standard tensile, plane strain fracture toughness, and fatigue crack propagation rate tests were performed on both the third- and fourth-generation composite material formulations using standard ASTM test techniques. Injection molding techniques were used to create random fiber orientation in all test specimens. Standard dog-bone style tensile specimens were tested to obtain ultimate tensile strength and stiffness. Compact tension fracture toughness specimens were utilized to determine plane strain fracture toughness values. Reduced thickness compact tension specimens were also used to determine fatigue crack propagation rate behavior for the two material groups. Literature values for the same parameters for human cortical bone were compared to results from the third- and fourth-generation cortical analogue bone materials. Tensile properties of the fourth-generation material were closer to that of average human cortical bone than the third-generation material. Fracture toughness was significantly increased by 48% in the fourth-generation composite as compared to the third-generation analogue bone. The threshold stress intensity to propagate the crack was much higher for the fourth-generation material than for the third-generation composite. Even at the higher stress intensity threshold, the fatigue crack propagation rate was significantly decreased in the fourth-generation composite compared to the third-generation composite. These results indicate that the bone analogue models made from the fourth-generation analogue cortical bone material may exhibit better performance in fracture and longer fatigue lives than similar models made of third-generation analogue cortical bone material. Further fatigue testing of the new composite material in clinically relevant use of bone models is still required for verification of these results. Biomechanical test models using the superior fourth-generation cortical analogue material are currently in development.

Sensitivity to acute methadone dose changes in maintenance patients.

This study assessed whether methadone patients can identify acute dose changes in their maintenance dose, and explored the relationships between self-reported drug effects and real or perceived dose changes. Four times each week patients (N = 10) unpredictably received either 80%, 90%, 100%, 110% or 120% of their usual daily dose (50-100 mg). Approximately 24 hr later they indicated which dose they had received on the previous day, and rated the previous day's dose in terms of good effects, bad effects, and change in medication taste. Correct estimation of the doses received was always at the levels expected by chance alone. Furthermore, this sample of patients could not detect dose-related changes in medication taste. However, self-reports of good effects were significantly higher when patients believed that they had received a dose increment, and ratings of bad effects were higher when patients believed that they had received a dose decrement.