Exploring the governing transport mechanisms of corrosive agents in a Canadian deep geological repository.

All nuclear energy producing nations face a common challenge associated with the long-term solution for their used nuclear fuel. After decades of research, many nuclear safety agencies worldwide agree that deep geological repositories (DGRs) are appropriate long-term solutions to protect the biosphere. The Canadian DGR is planned in either stable crystalline or sedimentary host rock (depending on the final site location) to house the used nuclear fuel in copper-coated used fuel containers (UFCs) surrounded by highly compacted bentonite. The copper-coating and bentonite provide robust protection against many corrosion processes anticipated in the DGR. However, it is possible that bisulfide (HS-) produced near the host rock-bentonite interface may transport through the bentonite and corrode the UFCs during the DGR design life (i.e., one million years); although container performance assessments typically account for this process, while maintaining container integrity. Because the DGR design life far exceeds those of practical experimentation, there is a need for robust numerical models to forecast HS- transport. In this paper we present the development of a coupled 3D thermal-hydraulic-chemical model to explore the impact of key coupled physics on HS- transport in the proposed Canadian DGR. These simulations reveal that, although saturation delayed and heating accelerated HS- transport over the first 100s and 10,000s of years, respectively, these times of influence were small compared to the long DGR design life. Consequently, the influence from heating only increased total projected HS- corrosion by <20% and the influence from saturation had a negligible impact (<1%). By comparing the corrosion rate results with a simplified model, it was shown that nearly-steady DGR design parameters governed most of the projected HS- corrosion. Therefore, those parameters need to be carefully resolved to reliably forecast the extent of HS- corrosion.

Quantified Pore-Scale Nanoparticle Transport in Porous Media and the Implications for Colloid Filtration Theory.

This study evaluates the pore-scale distribution of silver nanoparticles during transport through a sandy porous medium via quantitative synchrotron X-ray computed microtomography (qSXCMT). The associated distributions of nanoparticle flow velocities and mass flow rates were obtained by coupling these images with computational fluid dynamic (CFD) simulations. This allowed, for the first time, the comparison of nanoparticle mass flow with that assumed by the standard colloid filtration theory (CFT) modeling approach. It was found that (i) 25% of the pore space was further from the grain than assumed by the CFT model; (ii) the average pore velocity agreed well between results of the coupled qSXCMT/CFD approach and the CFT model within the model fluid envelope, although the former were 2 times larger than the latter in the centers of the larger pores and individual velocities were upwards of 20 times those in the CFT model at identical distances from grain surfaces ; and (iii) approximately 30% of all nanoparticle mass and 38% of all nanoparticle mass flow occurred further away from the grain surface than expected by the CFT model. This work suggests that a significantly smaller fraction of nanoparticles than expected will contact a grain surface by diffusion via CFT models, likely contributing to inadequate CFT model nanoparticle transport predictions.

Method for obtaining silver nanoparticle concentrations within a porous medium via synchrotron X-ray computed microtomography.

Attempts at understanding nanoparticle fate and transport in the subsurface environment are currently hindered by an inability to quantify nanoparticle behavior at the pore scale (within and between pores) within realistic pore networks. This paper is the first to present a method for high resolution quantification of silver nanoparticle (nAg) concentrations within porous media under controlled experimental conditions. This method makes it possible to extract silver nanoparticle concentrations within individual pores in static and quasi-dynamic (i.e., transport) systems. Quantification is achieved by employing absorption-edge synchrotron X-ray computed microtomography (SXCMT) and an extension of the Beer-Lambert law. Three-dimensional maps of X-ray mass linear attenuation are converted to SXCMT-determined nAg concentration and are found to closely match the concentrations determined by ICP analysis. In addition, factors affecting the quality of the SXCMT-determined results are investigated: 1) The acquisition of an additional above-edge data set reduced the standard deviation of SXCMT-determined concentrations; 2) X-ray refraction at the grain/water interface artificially depresses the SXCMT-determined concentrations within 18.1 µm of a grain surface; 3) By treating the approximately 20 × 10(6) voxels within each data set statistically (i.e., averaging), a high level of confidence in the SXCMT-determined mean concentrations can be obtained. This novel method provides the means to examine a wide range of properties related to nanoparticle transport in controlled laboratory porous medium experiments.

Impact of surfactant-induced wettability alterations on DNAPL invasion in quartz and iron oxide-coated sand systems.

Dense non-aqueous phase liquids (DNAPLs) present in the subsurface may contain surface active compounds that impact DNAPL migration and distribution. While a number of studies have revealed the role surface active compounds play in altering the wettability of quartz sand, few have considered the implications for other minerals common to contaminated sites. This study extends understanding of DNAPL/surfactant wettability to iron oxide surfaces. Specifically, quartz and iron oxide-coated sands in a tetrachloroethene (PCE)/water system containing the organic base (an organic molecule that acts as a base) dodecylamine (DDA) were compared at a variety of scales. Wettability of the minerals' surfaces, and the impact of wettability on capillary resistance to DNAPL entry, were assessed as a function of pH through: (i) advancing and receding contact angles, (ii) primary drainage capillary pressure-saturation experiments, and (iii) small, two-dimensional, flow cell experiments. The work revealed that, at neutral pH and under identical boundary capillary pressures, DNAPL invaded quartz sand but not iron oxide-coated sand; however, at low pH, DNAPL invaded both sands equally. These differences were demonstrated to be due to wettability alterations associated with the strength of attractive forces between DDA and the mineral surface, dictated by the isolectric point of the minerals and system pH. Observed differences in DNAPL invasion behavior were consistent with measured intrinsic contact angles and P(c)-S relationships, the latter requiring scaling by the operative contact angle inside the porous medium for a meaningful comparison. This study suggests that the distribution of minerals (and, more specifically, their isoelectric points), as well as the aqueous phase pH at a given site, may have a significant impact on the DNAPL source zone architecture.