Your browser doesn't support javascript.
loading
Show: 20 | 50 | 100
Results 1 - 20 de 37
Filter
Add more filters










Publication year range
1.
Gels ; 10(4)2024 Apr 22.
Article in English | MEDLINE | ID: mdl-38667702

ABSTRACT

Poly(ether ether ketone) (PEEK) was found to form gels in the benign solvent 1,3-diphenylacetone (DPA). Gelation of PEEK in DPA was found to form an interconnected, strut-like morphology composed of polymer axialites. To our knowledge, this is the first report of a strut-like morphology for PEEK aerogels. PEEK/DPA gels were prepared by first dissolving PEEK in DPA at 320 °C. Upon cooling to 50 °C, PEEK crystallizes and forms a gel in DPA. The PEEK/DPA phase diagram indicated that phase separation occurs by solid-liquid phase separation, implying that DPA is a good solvent for PEEK. The Flory-Huggins interaction parameter, calculated as χ12 = 0.093 for the PEEK/DPA system, confirmed that DPA is a good solvent for PEEK. PEEK aerogels were prepared by solvent exchanging DPA to water then freeze-drying. PEEK aerogels were found to have densities between 0.09 and 0.25 g/cm3, porosities between 80 and 93%, and surface areas between 200 and 225 m2/g, depending on the initial gel concentration. Using nitrogen adsorption analyses, PEEK aerogels were found to be mesoporous adsorbents, with mesopore sizes of about 8 nm, which formed between stacks of platelike crystalline lamellae. Scanning electron microscopy and X-ray scattering were utilized to elucidate the hierarchical structure of the PEEK aerogels. Morphological analysis found that the PEEK/DPA gels were composed of a highly nucleated network of PEEK axialites (i.e., aggregates of stacked crystalline lamellae). The highly connected axialite network imparted robust mechanical properties on PEEK aerogels, which were found to densify less upon freeze-drying than globular PEEK aerogel counterparts gelled from dichloroacetic acid (DCA) or 4-chlorphenol (4CP). PEEK aerogels formed from DPA were also found to have a modulus-density scaling that was far more efficient in supporting loads than the poorly connected aerogels formed from PEEK/DCA or PEEK/4CP solutions. The strut-like morphology in these new PEEK aerogels also significantly improved the modulus to a degree that is comparable to high-performance crosslinked aerogels based on polyimide and polyurea of comparable densities.

2.
Angew Chem Int Ed Engl ; 63(6): e202317699, 2024 Feb 05.
Article in English | MEDLINE | ID: mdl-38168073

ABSTRACT

In an effort to synthesize chemically recyclable thermoplastic elastomers, a redox-switchable catalytic system was developed to synthesize triblock copolymers containing stiff poly(lactic acid) (PLA) end blocks and a flexible poly(tetrahydrofuran-co-cyclohexene oxide) (poly(THF-co-CHO) copolymer as the mid-block. The orthogonal reactivity induced by changing the oxidation state of the iron-based catalyst enabled the synthesis of the triblock copolymers in a single reaction flask from a mixture of monomers. The triblock copolymers demonstrated improved flexibility compared to poly(l-lactic acid) (PLLA) and thermomechanical properties that resemble thermoplastic elastomers, including a rubbery plateau in the range of -60 to 40 °C. The triblock copolymers containing a higher percentage of THF versus CHO were more flexible, and a blend of triblock copolymers containing PLLA and poly(d-lactic acid) (PDLA) end-blocks resulted in a stereocomplex that further increased polymer flexibility. Besides the low cost of lactide and THF, the sustainability of this new class of triblock copolymers was also supported by their depolymerization, which was achieved by exposing the copolymers sequentially to FeCl3 and ZnCl2 /PEG under reactive distillation conditions.

3.
Adv Mater ; : e2307881, 2023 Nov 27.
Article in English | MEDLINE | ID: mdl-38009658

ABSTRACT

Additive manufacturing (AM) of aerogels increases the achievable geometric complexity, and affords fabrication of hierarchically porous structures. In this work, a custom heated material extrusion (MEX) device prints aerogels of poly(phenylene sulfide) (PPS), an engineering thermoplastic, via in situ thermally induced phase separation (TIPS). First, pre-prepared solid gel inks are dissolved at high temperatures in the heated extruder barrel to form a homogeneous polymer solution. Solutions are then extruded onto a room-temperature substrate, where printed roads maintain their bead shape and rapidly solidify via TIPS, thus enabling layer-wise MEX AM. Printed gels are converted to aerogels via postprocessing solvent exchange and freeze-drying. This work explores the effect of ink composition on printed aerogel morphology and thermomechanical properties. Scanning electron microscopy micrographs reveal complex hierarchical microstructures that are compositionally dependent. Printed aerogels demonstrate tailorable porosities (50.0-74.8%) and densities (0.345-0.684 g cm-3 ), which align well with cast aerogel analogs. Differential scanning calorimetry thermograms indicate printed aerogels are highly crystalline (≈43%), suggesting that printing does not inhibit the solidification process occurring during TIPS (polymer crystallization). Uniaxial compression testing reveals that compositionally dependent microstructure governs aerogel mechanical behavior, with compressive moduli ranging from 33.0 to 106.5 MPa.

4.
J Am Chem Soc ; 145(32): 18007-18014, 2023 Aug 16.
Article in English | MEDLINE | ID: mdl-37540785

ABSTRACT

Achromatic quarter waveplates (A-QWPs), traditionally constructed from multiple birefringent crystals, can modulate light polarization and retardation across a broad range of wavelengths. This mechanism is inherently related to phase retardation controlled by the fast and slow axis of stacked multi-birefringent crystals. However, the conventional design of A-QWPs requires the incorporation of multiple birefringent crystals, which complicates the manufacturing process and raises costs. Here, we report the discovery of a broadband (540-1060 nm) A-QWP based on a two-dimensional (2D) layered hybrid copper halide (HCH) perovskite single crystal. The 2D copper chloride (CuCl6) layers of the HCH crystal undergo Jahn-Teller distortion and subsequently trigger the in-plane optical birefringence. Its broad range of the wavelength response as an A-QWP is a consequence of the out-of-plane mosaicity formed among the stacked inorganic layers during the single-crystal self-assembly process in the solution phase. Given the versatility of 2D hybridhalide perovskites, the 2D HCH crystal offers a promising approach for designing cost-effective A-QWPs and the ability to integrate other optical devices.

5.
Nat Nanotechnol ; 18(7): 790-797, 2023 Jul.
Article in English | MEDLINE | ID: mdl-37081082

ABSTRACT

Mn dissolution has been a long-standing, ubiquitous issue that negatively impacts the performance of Mn-based battery materials. Mn dissolution involves complex chemical and structural transformations at the electrode-electrolyte interface. The continuously evolving electrode-electrolyte interface has posed great challenges for characterizing the dynamic interfacial process and quantitatively establishing the correlation with battery performance. In this study, we visualize and quantify the temporally and spatially resolved Mn dissolution/redeposition (D/R) dynamics of electrochemically operating Mn-containing cathodes. The particle-level and electrode-level analyses reveal that the D/R dynamics is associated with distinct interfacial degradation mechanisms at different states of charge. Our results statistically differentiate the contributions of surface reconstruction and Jahn-Teller distortion to the Mn dissolution at different operating voltages. Introducing sulfonated polymers (Nafion) into composite electrodes can modulate the D/R dynamics by trapping the dissolved Mn species and rapidly establishing local Mn D/R equilibrium. This work represents an inaugural effort to pinpoint the chemical and structural transformations responsible for Mn dissolution via an operando synchrotron study and develops an effective method to regulate Mn interfacial dynamics for improving battery performance.

6.
Soft Matter ; 18(40): 7762-7772, 2022 Oct 19.
Article in English | MEDLINE | ID: mdl-36205260

ABSTRACT

Quantitative analysis of particle size and size distribution is crucial in establishing structure-property relationships of composite materials. An emerging soft composite architecture involves dispersing droplets of liquid metal throughout an elastomer, enabling synergistic properties of metals and soft polymers. The structure of these materials is typically characterized through real-space microscopy and image analysis; however, these techniques rely on magnified images that may not represent the global-averaged size and distribution of the droplets. In this study, we utilize ultra-small angle X-ray scattering (USAXS) as a reciprocal-space characterization technique that yields global-averaged dimensions of eutectic gallium indium (EGaIn) alloy soft composites. The Unified fit and Monte Carlo scattering methods are applied to determine the particle size and size distributions of the liquid metal droplets in the composites and are shown to be in excellent agreement with results from real-space image analysis. Additionally, all methods indicate that the droplets are getting larger as they are introduced into composites, suggesting that the droplets are agglomerating or possibly coalescing during dispersion. This work demonstrates the viability of X-ray scattering to elucidate structural information about liquid metal droplets for material development for applications in soft robotics, soft electronics, and multifunctional materials.

7.
Carbohydr Polym ; 292: 119680, 2022 Sep 15.
Article in English | MEDLINE | ID: mdl-35725174

ABSTRACT

Crystallization inhibitors in amorphous solid dispersions (ASD) enable metastable supersaturated drug solutions that persist for a physiologically relevant time. Olefin cross-metathesis (CM) has successfully provided multifunctional cellulose-based derivatives as candidate ASD matrix polymers. In proof of concept studies, we prepared hydrophobic bile salt/cellulose adducts by CM with naturally occurring bile salts. We hypothesized that increased hydrophilicity would enhance the ability of these conjugates to maximize bioactive supersaturation. Their selective preparation presents a significant synthetic challenge, given polysaccharide reactivity and polysaccharide and bile salt complexity. We prepared such derivatives using a more hydrophilic hydroxypropyl cellulose (HPC) backbone, employing a pent-4-enyl tether (Pen) for appending bile acids. We probed structure-property relationships by varying the nature and degree of substitution of the bile acid substituent (lithocholic or deoxycholic acid). These conjugates are indeed synergistic inhibitors, as demonstrated with the fast-crystallizing prostate cancer drug, enzalutamide. The lithocholic acid methyl ester derivative, AcrMLC-PenHHPCPen (0.64), increased induction time 68 fold vs. drug alone.


Subject(s)
Bile Acids and Salts , Cellulose , Cellulose/chemistry , Crystallization , Humans , Hydrophobic and Hydrophilic Interactions , Male , Solubility
8.
ACS Appl Mater Interfaces ; 14(14): 16592-16600, 2022 Apr 13.
Article in English | MEDLINE | ID: mdl-35330991

ABSTRACT

We report on the morphology and mechanical properties of nanocomposite films derived from aqueous, hybrid liquid crystalline mixtures of rodlike aggregates of a sulfonated, all-aromatic polyamide, poly(2,2'-disulfonyl-4,4'-benzidine terephthalamide) (PBDT), and graphene oxide (GO) platelets. An isothermal step at 200 °C facilitates in situ partial thermal reduction of GO to reduced GO (rGO) in nanocomposite films. X-ray scattering studies reveal that PBDT-rGO nanocomposites exhibit both higher in-plane alignment of PBDT (the order parameter increases from 0.79 to 0.9 at 1.8 vol % rGO) and alignment along the casting direction (from 0.1 to 0.6 at 1.8 vol % rGO). From dynamic mechanical thermal analysis, the interaction between PBDT and rGO causes the ß-relaxation activation energy for PBDT to increase with rGO concentration. Modulus mapping of nanocomposites using atomic force microscopy demonstrates enhanced local stiffness, indicating reinforcement. From stress-strain analysis, the average Young's modulus increases from 16 to 37 GPa at 1.8 vol % rGO and the average tensile strength increases from 210 to 640 MPa. Despite polymer alignment along the casting direction, an average transverse tensile strength of 230 MPa is obtained.

9.
Molecules ; 26(15)2021 Aug 03.
Article in English | MEDLINE | ID: mdl-34361857

ABSTRACT

This work reveals the influence of pendant hydrogen bonding strength and distribution on self-assembly and the resulting thermomechanical properties of A-AB-A triblock copolymers. Reversible addition-fragmentation chain transfer polymerization afforded a library of A-AB-A acrylic triblock copolymers, wherein the A unit contained cytosine acrylate (CyA) or post-functionalized ureido cytosine acrylate (UCyA) and the B unit consisted of n-butyl acrylate (nBA). Differential scanning calorimetry revealed two glass transition temperatures, suggesting microphase-separation in the A-AB-A triblock copolymers. Thermomechanical and morphological analysis revealed the effects of hydrogen bonding distribution and strength on the self-assembly and microphase-separated morphology. Dynamic mechanical analysis showed multiple tan delta (δ) transitions that correlated to chain relaxation and hydrogen bonding dissociation, further confirming the microphase-separated structure. In addition, UCyA triblock copolymers possessed an extended modulus plateau versus temperature compared to the CyA analogs due to the stronger association of quadruple hydrogen bonding. CyA triblock copolymers exhibited a cylindrical microphase-separated morphology according to small-angle X-ray scattering. In contrast, UCyA triblock copolymers lacked long-range ordering due to hydrogen bonding induced phase mixing. The incorporation of UCyA into the soft central block resulted in improved tensile strength, extensibility, and toughness compared to the AB random copolymer and A-B-A triblock copolymer comparisons. This study provides insight into the structure-property relationships of A-AB-A supramolecular triblock copolymers that result from tunable association strengths.

10.
ACS Appl Mater Interfaces ; 13(44): 51894-51905, 2021 Nov 10.
Article in English | MEDLINE | ID: mdl-34086436

ABSTRACT

The aspect ratio (AR) of filler particles is one of the most critical determinants for the mechanical properties of particle-reinforced polymer composites. However, it has been challenging to solely study the effect of particle AR due to the difficulties of controlling AR without altering the physical and chemical properties of the particle. Herein, we synthesized PCN-222, a zirconium-based porphyrinic metal-organic framework (MOF) with preferential longitudinal growth as a series of particles with ARs increasing from 3.4 to 54. The synthetic MOF conditions allowed for the chemical properties of the particles to remain constant over the series. The particles were employed as reinforcers for poly(methyl methacrylate) (PMMA). MOF-polymer composite films were fabricated using doctor-blading techniques, which facilitated particle dispersion and alignment in the PMMA matrix, as revealed by optical microscopy and wide-angle X-ray diffraction. Mechanical measurements showed that both elastic and dynamic moduli increased with particle AR and particle concentrations but started to decrease as particle loading increased beyond 0.5 wt % (1.12 vol %). The data obtained at low particle loadings were fitted well with the Halpin-Tsai model. In contrast, the percolation model and the Cox model were unable to adequately fit the data, indicating the mechanical reinforcement in our system mainly originated from efficient load transfer between particles and the matrix in the particle orienting direction. Finally, we showed that the thermal stability of composite films increased with the addition of MOF particles because of the high thermal degradation temperature and restricted polymer chain mobility.

11.
ACS Appl Mater Interfaces ; 12(28): 32006-32016, 2020 Jul 15.
Article in English | MEDLINE | ID: mdl-32520520

ABSTRACT

This manuscript describes the versatility of highly directional, noncovalent interactions, i.e., quadruple hydrogen bonding (QHB), to afford novel polyurea segmented supramolecular polymers for melt extrusion three-dimensional (3D) printing processes. The molecular design of the polyurea elastomers features (1) flexible polyether segments and relatively weak urea hydrogen-bonding sites in the soft segments to provide elasticity and toughness, and (2) strong ureido-cytosine (UCyt) QHB in the hard segments to impart enhanced mechanical integrity. The resulting polyureas were readily compression-molded into mechanically-robust, transparent, and creasable films. Optimization of polyurea composition offered a rare combination of high tensile strength (95 MPa), tensile elongation (788% strain), and toughness (94 MJ/m3), which are superior to a commercially available Ninjaflex elastomer. The incorporation of QHB facilitated melt processability, where hydrogen bonding dissociation provided low viscosities at printing temperatures. During cooling, directional self-assembly of UCyt QHB facilitated the solidification process and contributed to part fidelity with the formation of a robust physical network. The printed objects displayed high layer fidelity, smooth surfaces, minimal warpage, and complex geometries. The presence of highly directional QHB effectively diminished mechanical anisotropy, and the printed samples exhibited comparable Young's moduli along (x-y direction, 0°) and perpendicular to (z-direction, 90°) the layer direction. Remarkably, the printed samples exhibited ultimate tensile strains approaching 500% in the z-direction prior to failure, which was indicative of improved interlayer adhesion. Thus, this design paradigm, which is demonstrated for novel polyurea copolymers, suggests the potential of supramolecular polymers with enhanced mechanical performance, melt processability, recyclability, and improved interlayer adhesion for melt extrusion additive manufacturing processes.

12.
Biomacromolecules ; 21(5): 1729-1738, 2020 05 11.
Article in English | MEDLINE | ID: mdl-31940434

ABSTRACT

Preparation of polysaccharide-based block copolymers with linear architectures is an important goal, opening up clear application potential and requiring significant advances in polysaccharide regio- and chemoselectivity. Herein we report a simple approach to prepare dextran-based block copolymers. Reaction with N-bromosuccinimide (NBS)/triphenyl phosphine (PPh3) regioselectively brominates the sole primary alcohol of linear, unbranched dextran at C-6 of the nonreducing end monosaccharide. The resulting dextran, monofunctionalized with a terminal C-6 bromide, was coupled with various amine terminated polymers to prepare block copolymers, including dextran-b-poly(ethylene glycol), dextran-b-polystyrene, and dextran-b-poly(N-isopropylacrylamide). These renewable-based block copolymers, prepared in two selective, high-yielding steps from native linear dextran, exhibit various interesting properties. Dextran-b-poly(N-isopropylacrylamide) undergoes thermally induced micellization as revealed by dynamic light scattering (DLS), forming micelles upon exceeding 33 °C. We also observed microphase separation in dextran-b-polystyrene by using small-angle X-ray scattering (SAXS). Overall, this methodology provides a new, highly chemo- and regioselective, versatile route to diverse dextran-based block copolymers with useful properties, enabling drug delivery, compatibilization, and other applications.


Subject(s)
Dextrans , Halogenation , Micelles , Polyethylene Glycols , Polymers , Scattering, Small Angle , X-Ray Diffraction
13.
ACS Appl Mater Interfaces ; 11(34): 31508-31519, 2019 Aug 28.
Article in English | MEDLINE | ID: mdl-31379150

ABSTRACT

The phase diagram for the thermoreversible gelation of poly(ether ether ketone) (PEEK) in 4-chlorophenol (4CP) was constructed over broad temperature and concentration ranges, revealing that PEEK is capable of dissolving and forming gels in both 4CP and dichloroacetic acid (DCA) up to a concentration of 25 wt %. Highly porous aerogels of PEEK were prepared through simple solvent exchange followed by one of two drying methods of solvent removal from the wet gel: freeze-drying or supercritical CO2 fluid extraction (SC-drying). The field-emission scanning electron microscopy analysis showed that gelation of PEEK in 4CP, followed by SC-drying, produced aerogels with well-defined lamellar aggregates as compared to less ordered aggregates formed from DCA. Mechanical properties (in compression) were shown to improve with increasing density, resulting in equivalent compressive moduli at comparable density, regardless of the preparation method (gelation solvent selection, concentration variation, or drying method). Nitrogen adsorption-desorption isotherms indicate that PEEK aerogels are comprised of mesopores (2-50 nm diameter pores) formed from stacked crystalline lamella. PEEK aerogels prepared using SC-drying exhibit higher Brunauer-Emmett-Teller surface areas than freeze-dried aerogels of comparable density. The ultra-small-angle X-ray scattering/small-angle X-ray scattering (SAXS)/wide-angle X-ray scattering analysis revealed a hierarchical morphology of the PEEK aerogels with structural features from PEEK crystallites to agglomerates of stacked lamella that spanned a wide range of length scales. SANS contrast-matching confirmed that the morphological origin of the principle scattering feature in PEEK aerogels is stacked crystalline lamella. Nitrogen sorption measurements of porosity and the specific surface area of the PEEK aerogels were correlated with the SAXS analysis to reveal a remarkably high surface area attributed to the platelet-like, lamellar morphology. Contact angle and contact angle hysteresis (CAH) revealed that low-density PEEK aerogels (ρ < 0.15 g/cm3) have water contact angles above the superhydrophobicity cutoff angle (>150°) and a very low CAH near 1°.

14.
Nat Commun ; 10(1): 801, 2019 02 18.
Article in English | MEDLINE | ID: mdl-30778067

ABSTRACT

The ubiquitous biomacromolecule DNA has an axial rigidity persistence length of ~50 nm, driven by its elegant double helical structure. While double and multiple helix structures appear widely in nature, only rarely are these found in synthetic non-chiral macromolecules. Here we report a double helical conformation in the densely charged aromatic polyamide poly(2,2'-disulfonyl-4,4'-benzidine terephthalamide) or PBDT. This double helix macromolecule represents one of the most rigid simple molecular structures known, exhibiting an extremely high axial persistence length (~1 micrometer). We present X-ray diffraction, NMR spectroscopy, and molecular dynamics (MD) simulations that reveal and confirm the double helical conformation. The discovery of this extreme rigidity in combination with high charge density gives insight into the self-assembly of molecular ionic composites with high mechanical modulus (~ 1 GPa) yet with liquid-like ion motions inside, and provides fodder for formation of other 1D-reinforced composites.


Subject(s)
Phthalimides/chemistry , Polyelectrolytes/chemistry , Polymers/chemistry , Magnetic Resonance Spectroscopy , Molecular Conformation , Molecular Dynamics Simulation , X-Ray Diffraction
15.
J Phys Chem B ; 121(25): 6238-6244, 2017 06 29.
Article in English | MEDLINE | ID: mdl-28558217

ABSTRACT

The creation of renewable fuels to replace dwindling fossil energy resources is one of the greatest challenges facing the scientific community. Generating H2 fuel from water is a carbon-neutral strategy that demonstrates great promise. Photocatalysts of the molecular architecture [{(TL)2Ru(BL)}2RhX2]5+ (BL = bridging ligand, TL = terminal ligand, X = halide) catalyze the formation of H2 in deoxygenated organic solvents but are limited by poor performance in air-saturated aqueous solutions. Addition of the water-soluble polyelectrolyte poly(sodium 4-styrenesulfonate) (PSS) was recently shown as being a promising new strategy to increase efficiency and stability of H2 evolving photocatalysts in air-saturated aqueous solutions. Herein we investigate intermolecular interactions between Ru,Rh,Ru photocatalysts and water-soluble polyelectrolytes using isothermal titration calorimetry (ITC). ITC studies provide insight into the thermodynamic forces that drive assembly of PSS-photocatalyst aggregates and give new evidence for the intermolecular forces that lead to increased photocatalytic efficiency.

16.
ACS Macro Lett ; 6(3): 262-266, 2017 Mar 21.
Article in English | MEDLINE | ID: mdl-35650924

ABSTRACT

Solutions of poly(ether ether ketone) in dichloroacetic acid have been shown to form monolithic, thermoreversible gels at temperatures ranging from 10 to 140 °C. A phase diagram was constructed over broad concentration and temperature ranges, and the phase boundary suggests an upper critical solution temperature (UCST) behavior. Furthermore, poly(ether ether ketone) (PEEK) gels were solvent-exchanged with water to form hydrogels and subsequently lyophilized to form PEEK aerogels. The PEEK aerogels of density 0.2 g/mL were found to be highly porous and composed of uniform 200 nm morphological features. The crystal structure of the PEEK hydrogels and aerogels was found to be identical to that of melt-crystallized PEEK. The mechanical properties of the PEEK aerogels (in compression) were found to be superior to conventional silicate aerogels of comparable density. This report is the first example of a monolithic, thermoreversible gel of PEEK and the first demonstration of PEEK hydrogels and aerogels.

17.
Chem Commun (Camb) ; 52(56): 8663-6, 2016 Jul 05.
Article in English | MEDLINE | ID: mdl-27250778

ABSTRACT

Addition of sulfonated terminal ligands into a Ru,Rh,Ru photocatalyst has a significant impact on the excited-state properties of the complex. The hydrophilic photocatalyst demonstrates increased solubility and H2 production in aqueous solutions. H2 production is observed under aerobic conditions for the new complex, a stark contrast to the hydrophobic analog in organic solvents.

18.
Chem Commun (Camb) ; 52(48): 7564-7, 2016 Jun 18.
Article in English | MEDLINE | ID: mdl-27194643

ABSTRACT

ABC triblock copolymers bearing adenine- and thymine-functionalized external blocks self-assembled into long-range, ordered lamellar microphase-separated morphologies on non-patterned substrates. Intermolecular hydrogen bonding formed thymine-adenine triplets and promoted self-assembly into well-defined lamellae consisting of poly(n-butyl acrylate) soft domains and complementary nucleobase hard domains, while thymine-adenine duplets contributed to superior mechanical properties.

19.
Chem Commun (Camb) ; 52(5): 950-3, 2016 Jan 18.
Article in English | MEDLINE | ID: mdl-26587572

ABSTRACT

Living anionic polymerization of 4-diphenylphosphino styrene (DPPS) achieved well-defined homopolymers, poly(DPPS-b-S) styrenic block copolymers, and poly(I-b-DPPS) diene-based diblock copolymers with predictable molecular weights and narrow polydispersities. In situ FTIR spectroscopy monitored the anionic polymerization of DPPS and tracked monomer consumption for kinetic analysis. Post-alkylation enabled controlled placement of phosphonium functionality in poly(I-b-DPPS) diblock copolymers, producing well-defined phosphonium-containing block copolymers with low degrees of compositional heterogeneity. Incorporating phosphonium charge disrupted the lamellar bulk morphology of the neutral diblock precursor and provided morphologies with interdigitated packing of alkyl chains on the phosphonium cation.

20.
ACS Appl Mater Interfaces ; 8(2): 1280-8, 2016 Jan 20.
Article in English | MEDLINE | ID: mdl-26699795

ABSTRACT

Two-step reversible addition-fragmentation chain transfer (RAFT) polymerization and two subsequent postpolymerization modification steps afforded well-defined ABA triblock copolymers featuring mechanically reinforcing polystyrene outer blocks and 1-methylimidazole-neutralized poly(acrylic acid)-based central blocks. Size exclusion chromatography and (1)H NMR spectroscopy confirmed predictable molecular weights and narrow distributions. The ionic liquid (IL) 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ([EMIm][OTf]) was incorporated at 30 wt % into polymeric films. Thermogravimetric analysis, differential scanning calorimetry, and dynamic mechanical analysis determined the thermomechanical properties of the polymers and polymer-IL composites. Atomic force microscopy, small-angle X-ray scattering (SAXS), and transmission electron microscopy (TEM) determined surface and bulk morphologies, and poly(Sty-b-AA(MeIm)-b-Sty) exhibited a change from packed cylindrical to lamellar morphology in SAXS upon IL incorporation. Electrochemical impedance spectroscopy determined the in-plane ionic conductivities of the polymer-IL membranes (σ ∼ 10(-4) S/cm). A device fabricated from poly(Sty-b-AA(MeIm)-b-Sty) with 30 wt % incorporated IL demonstrated mechanical actuation under a low applied voltage of 4 V.

SELECTION OF CITATIONS
SEARCH DETAIL
...