Pilot scale validation campaign of gel dosimetry for pre-treatment quality assurance in stereotactic radiotherapy.

PURPOSE: Complex stereotactic radiotherapy treatment plans require prior verification. A gel dosimetry system was developed and tested to serve as a high-resolution 3D dosimeter for Quality Assurance (QA) purposes. MATERIALS AND METHODS: A modified version of a polyacrylamide polymer gel dosimeter based on chemical response inhibition was employed. Different sample geometries (cuvettes and phantoms) were manufactured for calibration and QA acquisitions. Irradiations were performed with a Varian Trilogy linac, and analyses of irradiated gel dosimeters were performed via MRI with a 1.5 T Philips Achieva at 1 mm3 or 2 mm3 isotropic spatial resolution. To assess reliability of polymer gel data, 54 stereotactic clinical treatment plans were delivered both on dosimetric gel phantoms and on the Delta4 dosimeter. Results from the two devices were evaluated through a global gamma index over a range of acceptance criteria and compared with each other. RESULTS: A quantitative and tunable control of dosimetric gel response sensitivity was achieved through chemical inhibition. An optimized MRI analysis protocol allowed to acquire high resolution phantom dose data in timeframes of ≈ 1 h. Conversion of gel dosimeter data into absorbed dose was achieved through internal calibration. Polymer gel dosimeters (2 mm3 resolution) and Delta4 presented an agreement within 4.8 % and 2.7 % at the 3 %/1 mm and 2 %/2 mm gamma criteria, respectively. CONCLUSIONS: Gel dosimeters appear as promising tools for high resolution 3D QA. Added complexity of the gel dosimetry protocol may be justifiable in case of small target volumes and steep dose gradients.

Topsoil radiological characterisation of L-54M reactor surroundings preliminary to decommissioning operations.

The radiological characterization of the topsoil of the L-54M reactor surroundings carried out in this work aims at obtaining the reference blank point for the forthcoming decommissioning operations and ascertain if unexpected radionuclide release occurred during the operational life of the plant. Standardised methods have been employed in order to collect representative samples and reliable results. Suitable sample pre-treatment procedures were applied. Gamma and beta spectrometric analyses were carried out to measure the activity concentrations of 60Co 137Cs, 152Eu, 241Am and 90Sr. These have been considered as representative radionuclides that could have been originated from reactor operations and that could still be present at four decades post reactor shutdown.

[Development of the agricultural sector in Italy: need to harmonize production and health protection]. / Lo sviluppo dell'agricoltura in Italia oggi: necessità di armonizzare aspetti produttivi e di tutela della salute.

Epidemiological data show excess of respiratory, dermatological, infectious, carcinogenic and musculoskeletal disorders among agricultural workers. Nevertheless, the national rates of reported cases do not correspond to the expected epidemiological data. In 2009, 3.914 cases of occupational diseases were reported to the national work compensation Institute (INAIL), as related to 1,200.000 agricultural workers employed in Italy. About 71% of these cases were related to musculoskeletal disorders. This shows a relevant difference between observed and expected cases, even more evident than in other sectors like constructions. More efficient preventive intervention is needed to improve this situation of under-reporting, through the implementation of epidemiological surveillance based on multiple sources of information. These sources should include the periodical health surveillance of active workers, the databank of General Practitioners, the hospital admission charts, and the case-lists of patients admitted to the Institutes of Occupational Health, according to a systematic active search of occupational cases.

[Biological monitoring in the molding of plastics and rubbers]. / Monitoraggio biologico nello stampaggio di plastiche e gomme.

This survey was carried out in the molding of plastics and rubbers, in the "Professional Cancer Prevention Project" sponsored by the Lombardy region with the objective of developing and implementing protocols for evaluating exposure to carcinogens through the biological monitoring. The realities of molding the thermoplastic polymer ABS, rubber, and thermosetting plastics containing formaldehyde were examined. The carcinogenic substances identified in these processes were: 1,3-butadiene, acrylonitrile and styrene in molding ABS, polycyclic aromatic hydrocarbons (PAH) in molding rubber, and formaldehyde in molding the thermosetting plastics. Only for some of these substances biological indicators are available. The limited exposure to airborne chemicals in molding ABS and the intrinsic characteristics of biological indicators available for 1-3 butadiene have determined the non applicability of biological monitoring to this situation. The absence of a biological indicator of exposure to formaldehyde has made this situation not investigable. Exposure in the rubber molding was studied in 19 subjects applying the determination not metabolized PAH in urine. The levels of these indicators were similar to those measured in other groups of subjects without occupational exposure to PAH, confirming a low airborne contamination in this workplace.

[Exposure to polycyclic aromatic hydrocarbons (PAH) in rubber forming industry]. / Esposizione ad idrocarburi policiclici aromatici nello stampaggio della gomma.

Among various chemical agents present at the workplaces in the rubber industry, a particular attention was adressed to the Polycyclic Aromatic Hydrocarbons (PAH) contained in oil and carbon black, but some questions regarding level of exposure are also controversially discussed. The literature reports that PAH may have irritant effects; moreover some of these have been recognized as probably or possibly carcinogenic to human by the International Agency for Research on Cancer, the European Union, and other institutions. In Lombardy, a study aimed to evaluate the occupational exposure in Benzo[b]fluorantene the rubber forming industry was planned during last two years. The results of environmental air monitoring (the 16 most relevant, according to the American Environmental Protection Agency, EPA) and biological monitoring (urinary 1-hydroxypyrene excretion) show that PAH exposure in these workers is not higher than that observed in other study regarding low level and acceptable exposure.

[Rubber industry and exposure to carcinogenic chemical agents: an Italian Multicentric Study in Lombardy]. / Stampaggio della gomma ed agenti chimici cancerogeni: l'esperienza dello Studio PPTP-Gomma.

Evaluating the chemical risks at the workplaces, the potential carcinogenic risk is a primary interest. Particularly, in the rubber forming industry the main attention was directed to the hot processing as a possible source of exposure to chemical agents, several of which were classified as carcinogens by the International Agency for Research on Cancer (IARC) and/or the European Union (EU). A study on occupational exposure to chemical carcinogens in the rubber forming industry was planned during last two years, involving a representative sample of firms. In the first step the occupational exposure and the use of preventive measures were evaluated by an investigation at workplace supported with standardized questionnaires. The presence of above 100 chemical agents was registered; 15 agents were classified to carcinogenic or probably carcinogenic to human. The evaluation of exposure by air sampling and monitoring of most substances of interest (acrylonitrile, 1,3-butadiene, styrene, Polycyclic Aromatic Hydrocarbons), demonstrated a low level of occupational exposure, the common hygienic prevention measure being applied.

Exposure to mutagenic airborne particulate in a rubber manufacturing plant.

Epidemiological studies conducted in the 1980s revealed that people working in the rubber manufacturing industry had an increased risk of cancer. Even now, workers employed in rubber processing are still at risk despite the measures adopted to improve their working conditions. The aim of the study was to evaluate the presence of a genotoxic risk in a rubber industry and to verify whether or not it was possible to locate the most dangerous position among the different rubber-working processes. The mutagenic activity of airborne particulate was evaluated in samples collected in the mixing department of a rubber manufacturing plant. Ambient air samples were taken over 3-h period in two stable positions near the mixing (Banbury mixer) and calendering areas. Personal air samples were taken over 2-h period during a normal workday from five workers employed in different rubber processing operations (mixing, weighing, calendering, compounding and extruding). The mutagenic activity of the air samples was determined by plate incorporation assay using Salmonella typhimurium strains (TA 98, TA 98NR, TA 100, YG 1021) with and without metabolic activation. Polycyclic aromatic hydrocarbon (PAH) concentrations were determined by high-performance liquid chromatography (HPLC); the presence of other presumable contaminants were carried out by gas chromatography-mass spectrometry (GC-MS). The results showed substantial direct and indirect frameshift mutagenicity in both ambient and personal samples. No mutagenic activity was present in S. typhimurium TA 100, except in the personal sample from a worker employed on the Banbury mixer. HPLC analysis revealed very low concentrations of PAHs. GC-MS analysis showed the presence of compounds such as azulene derivative, 1,2-dihydro-2,2,4-trimethylquinoline, N-methyl N-phenylbenzenamine, diphenylamine, bis(2-ethylhexyl)phthalate and bis(methyl-propyl)phthalate. We conclude that the high levels of mutagenic activity in ambiental and personal samples indicate the presence of substances with high genotoxic potency; no substantial differences were seen among the several rubber processing operations. PAHs were not involved in indoor pollution. GC-MS analysis revealed the presence of compounds which may be produced by high temperatures to which the raw materials are subjected during rubber manufacturing processes. These substances are potential carcinogen though their mutagen properties have not been clearly determined.