ABSTRACT
In this study, a quartz crystal microbalance (QCM) aptasensor for carcinoembryonic antigen (CEA), a well-known biomarker for various cancer types, was reported, utilizing two different aptamers. To achieve this, a nanofilm of 4-mercaptophenyl was electrochemically attached to gold-coated QCM crystal surfaces via the reduction of 4-mercaptobenzenediazonium salt (4 MB-DAT) using cyclic voltammetry. Subsequently, gold nanoparticles (AuNP) were affixed to this structure, and then aptamers (antiCEA1 and antiCEA2) modified with SH-functional ends bound to AuNPs completed the modification. The analytical performance of the CEA sensor was evaluated through simultaneous QCM measurements employing CEA solutions ranging from 0.1 ng/mL to 25 ng/mL. The detection limit (LOD) for CEA was determined to be 102 pg/mL for antiCEA1 and 108 pg/mL for antiCEA2 aptamers. Interday and intraday precision and accuracy tests yielded maximum results of 4.3 and + 3.8, respectively, for both aptasensors, as measured by relative standard deviation (RSD%) and relative error (RE%). The kinetic data of the aptasensors resulted in affinity values (KD) of 0.43 ± 0.14 nM for antiCEA1 and 0.75 ± 0.42 nM for antiCEA2. These values were lower than the reported values of 3.9 nM and 37.8 nM for both aptamers, respectively. The selectivity of the aptasensor was evaluated by measuring the signal changes caused by alpha-fetoprotein (AFP), cancer antigen (CA-125), and vascular endothelial growth factor (VEGF-165) individually and together at a concentration of 500 ng/mL, resulting in a maximum 4.1 % change, which was comparable to precision and accuracy values reported in the literature. After confirming the selectivity of the aptamers, recovery experiments were conducted using spiked commercial serum samples to simulate real samples, and the lowest recovery value obtained was 95.4 %. It was determined that two different aptasensors could be successfully used for the QCM-based detection of CEA in this study.
ABSTRACT
In this research, a cyanobacteria (Leptolyngbia sp.)-based biological photovoltaic cell (BPV) was designed. This clean energy-friendly BPV produced a photocurrent as a result of illuminating the photoanode and cathode electrodes immersed in the aqueous medium with solar energy. For this purpose, both electrodes were first coated with conductive polymers with aniline functional groups on the gold electrodes. In the cell, the photoanode was first coated with a gold-modified poly 4-(2,5-di(thiophen-2-yl)-1H-pyrrol-1-yl)benzamine polymer, P(SNS-Aniline). Thioaniline-functionalized gold nanoparticles were used to provide a cross-link formation with bis-aniline conductive bonds with the conductive polymer using electrochemical techniques. Leptolyngbia sp., one of the cyanobacteria that can convert light energy into chemical energy, was attached to this layered electrode surface. The cathode of the cell was attached to the gold electrode surface with P(SNS-Aniline). Then, the bilirubin oxidase (BOx) enzyme was immobilized on this film surface with glutaraldehyde activation. This cell, which can use light, thanks to cyanobacteria, oxidized and split water, and oxygen was obtained at the photoanode electrode. At the cathode electrode, the oxygen gas was reduced to water by the bioelectrocatalytic method. To obtain a high photocurrent from the BPV, necessary optimizations were made during the design of the system to increase electron transport and strengthen its transfer. While the photocurrent value obtained with the designed BPV in optimum conditions and in the pseudosteady state was 10 mA/m2, the maximum power value obtained was 46.5 mW/m2. In addition to storing the light energy of the system, studies have been carried out on this system as a pesticide biosensor. Atrazine biosensing via the BPV system was analytically characterized between 0.1 and 1.2 µM concentrations for atrazine, and a very low detection limit was found as 0.024 µM. In addition, response time and recovery studies related to pesticide biosensor properties of the BPV were also investigated.
ABSTRACT
A sensitive and selective electrochemical sensor for the determination of paracetamol (acetaminophen) is proposed based on a polyglycine-coated glassy carbon electrode. The electrochemical behavior of paracetamol was studied by cyclic voltammetry and differential pulse voltammetry. Under optimal experimental conditions, the peak oxidation current of paracetamol increases linearly in the range of 0.5-75 µM. The limit of detection of paracetamol was 0.03 µM and the limit of quantitation was 0.09 µM. In addition, modified glassy carbon with polyglycine as the sensor was successfully used for the determination of paracetamol in antipyretic children's syrup samples, with a recovery rate of over 95.3%, showing its great application potential in drug analysis.
Subject(s)
Acetaminophen , Antipyretics , Child , Humans , Acetaminophen/analysis , Carbon , Electrochemical Techniques , ElectrodesABSTRACT
Electrochemical oxidation of quercetin, as an important biological molecule, has been studied in non-aqueous media using cyclic voltammetry, electrochemical impedance spectroscopy and scanning electron microscopy. To investigate the electrochemical properties of quercetin, an important flavonoid derivative, on a different surface, a new glassy carbon electrode has been developed using dithiooxamide as modifier in non-aqueous media. The surface modification of glassy carbon electrode has been performed within the 0.0 mV and +800 mV potential range with 20 cycles using 1 mM dithioxamide solution in acetonitrile. However, the modification of quercetin to both bare glassy carbon and dithiooxamide modified glassy carbon electrode surface was carried out in a wide +300 mV and +2,800 mV potential range with 10 cycles. Following the modification process, cyclic voltammetry has been used for the surface characterization in aqueous and non-aqueous media whereas electrochemical impedance spectroscopy has been used in aqueous media. Scanning electron microscopy has also been used to support the surface analysis. The obtained data from the characterization and modification studies of dithioxamide modified and quercetin grafted glassy carbon electrode showed that the developed electrode can be used for the quantitative determination of quercetin and antioxidant capacity determination as a chemical sensor electrode.
