ABSTRACT
BACKGROUND: High-performance polymers are used in different fixed prosthesis treatments due to their many advantages such as biocompatibility, shock absorption ability, high fracture resistance. The effects of marginal design on the forces on high-performance polymers are unknown. This study aimed was to investigate the stress distribution of different marginal designs on Polyetheretherketone (PEEK) and Polyetherketoneketone (PEKK) substructure materials, cortical bone and cancellous bone by finite element analysis. METHODS: A first maxillary molar tooth was modeled in 3D using the "3D Complex Render" method. Considering the ideal preparation conditions (Taper angle was 6°, step depth was 1 mm, occlusal reduction was 2 mm), four different configurations were modeled by changing the marginal design (chamfer, deep chamfer, shoulder 90°, shoulder 135°). PEEK, PEKK substructure, and composite superstructure were designed on created models. A total of 150 N oblique force from two points and a total of 300 N vertical force from three points were applied from occlusall. and the maximum principal stress, minimum principal stress, von Mises stress findings in the cortical bone, spongiose bone, and substructure were examined. The study was carried out by static linear analysis with a three-dimensional finite element stress analysis method. RESULTS: The highest maximum principal stress value in the cortical bone was observed when the PEEK + Shoulder 135° step at vertical force. The highest minimum principal stress value in the cortical bone was observed when the PEEK + Shoulder 90° step, and PEEK + deep chamfer step at oblique force. The highest maximum principal stress value in spongiose bone was observed when the PEEK + Shoulder 90° step. The highest minimum principal stress value in spongiose bone was observed when the PEEK + deep chamfer step at vertical force. The highest von Mises stress value in the substructure was observed when the PEKK + Deep chamfer step at oblique force. The lowest maximum principal stress value in the cortical bone was observed when the PEKK + Shoulder 135° step at oblique force. The lowest minimum principal stress value in the cortical bone was observed when the PEEK + Shoulder 135° step, and PEKK + shoulder 135° step at vertical force. The lowest maximum principal stress value in spongiose bone was observed when the PEEK + Shoulder 90° step. The lowest minimum principal stress value in spongiose bone was observed when the PEEK + Shoulder 135° step and PEKK + Shoulder 135° step at vertical force. The lowest von Mises stress value in the substructure was observed when the PEEK + Deep chamfer step at vertical force. CONCLUSION: When cortical and spongiose bone stress were evaluated, no destructive stress was observed. Considering the stresses occurring in the substructure the highest stress was observed in the chamfer step.
ABSTRACT
OBJECTIVE: Laser irradiation is an alternative surface treatment method for roughening zirconia surfaces. The aim of this study was to evaluate the effects of ytterbium-doped fiber laser (YbPL) on zirconia. BACKGROUND: Zirconia surfaces are resistant to many surface treatment methods, but surface roughness is crucial for adhesion of veneering materials and cements to zirconia. METHODS: The zirconia discs were prepared and divided into four groups according to the power of the laser irradiation (5, 12, 17, and 20 W). These groups were divided into five subgroups according to the frequency (25, 40, 60, 80, and 100 kHz). Surface roughness values were measured with a noncontact profilometer, and the mean Ra values were calculated. Wettability was measured with a goniometer. The surface morphology was observed with a scanning electron microscope (SEM). The changes in the surface crystalline structure were analyzed with X-ray diffractometry. RESULTS: Ra values of all groups were higher than the control group. The highest surface roughness value was at 20 W and 100 kHz. Best wettability characteristic was observed at 5 W and 60 kHz. The correlations between Ra and wettability were low but significant. SEM examination of 5 W with different frequencies showed no microcracks, however, melted areas were observed. Remaining groups had microcracks and melted layers. A significantly lower T/M-phase transformation was observed in some groups. CONCLUSIONS: YbPL irradiation was effective at roughening the zirconia surface. Although laser treatment affected zirconia surfaces and provided surface roughness, the power and frequency should be adjusted to achieve optimum results.
