Multiphysics model of liquid-cooled Nd:phosphate split-slabs in large aperture optical amplifiers.

High repetition rates in high energy solid-state laser systems can yield to a rise of temperature in amplifiers despite the use of cooling systems. This effect can significantly impact the performance of amplifiers by inducing thermal stress, birefringence or thermal lensing. Here, we develop a multiphysics model to support the design, optimization and commissioning of a liquid-cooled large aperture split-slab laser glass amplifier. This multiphysics model includes optical pumping in the amplifying medium, heat loading, hydraulic effects induced by the liquid coolant, mechanical deformation and their potential coupled effects on the optical wavefront. The accuracy of each model is assessed by carrying out specific experimental measurements and characterizations. We show that this set of models allows the prediction of performance of a liquid-cooled amplifier from the flash-lamp emission to the amplified wavefront at a repetition rate of one shot per minute.

Influence of absorption-edge properties on subpicosecond intrinsic laser-damage threshold at 1053 nm in hafnia and silica monolayers.

Owing to their relatively high resistance to laser-induced damage, hafnia and silica are commonly used in multilayered optical coatings in high-power laser facilities as high- and low-refractive-index materials, respectively. Here, we quantify the laser-induced-damage threshold (LIDT) at 1053 nm in the short-pulse regime of hafnia and silica monolayers deposited by different fabrication methods, including electron-beam evaporation, plasma ion-assisted deposition and ion-assisted deposition. The results demonstrate that nominally identical coatings fabricated by different deposition techniques and/or vendors can exhibit significantly different damage thresholds. A correlation of the LIDT performance of each material with its corresponding absorption edge is investigated. Our analysis indicates a weak correlation between intrinsic LIDT and the optical gap of each material (Tauc gap) but a much better correlation when considering the spectral characteristics in the Urbach tail spectral range. Spectrophotometry and photothermal absorption were used to provide evidence of the correlation between the strength of the red-shifted absorption tail and reduced LIDT at 1053 nm.

1.15 PW-850 J compressed beam demonstration using the PETAL facility.

The Petawatt Aquitaine Laser (PETAL) facility was designed and constructed by the French Commissariat à l'énergie atomique et aux énergies alternatives (CEA) as an additional PW beamline to the Laser MegaJoule (LMJ) facility. PETAL energy is limited to 1 kJ at the beginning due to the damage threshold of the final optics. In this paper, we present the commissioning of the PW PETAL beamline. The first kJ shots in the amplifier section with a large spectrum front end, the alignment of the synthetic aperture compression stage and the initial demonstration of the 1.15 PW @ 850 J operations in the compression stage are detailed. Issues encountered relating to damage to optics are also addressed.

Relations between subsurface damage depth and surface roughness of grinded fused silica.

Relationships between subsurface damage (SSD) depth and peak to valley surface roughness (Rt) have been widely studied and present a major interest for an easy assessment of the SSD depth. We look at the relation between SSD depth and other surface roughness parameters using the Abbott-Firestone curve on a large campaign of grinding tests (with different abrasive grain size, grinding speed and grinding mode). The results reveal that Abbott-Firestone parameters are better for an assessment of SSD depth and that relationships between SSD depth and surface roughness are not universal but depend on the grinding process.

Mixed metal dielectric gratings for pulse compression.

We report on manufacturing and testing results of high efficiency mixed metal dielectric gratings (MMLD) for high power pulse compression applications. The gratings with 1780 l/mm are etched in the top low index layer of a Au-(SiO2/HfO2)4-SiO2 mirror stack. Various grating profiles manufactured in order to modify the near electric field distribution are damage tested on a facility operating at 1.053 µm, 500 fs pulse duration. We evidence that damage threshold is governed by the value of the maximum electric field intensity inside the grating pillar. Moreover thresholds close to 3 J/cm2 beam normal are obtained with this new MMLD grating being thus an interesting alternative to gold and pure dielectric gratings for pulse compression applications.

Evidence of a green luminescence band related to surface flaws in high purity silica glass.

Using luminescence confocal microscopy under 325 nm laser excitation, we explore the populations of defects existing in or at the vicinity of macroscopic surface flaws in fused silica. We report our luminescence results on two types of surface flaws: laser damage and indentation on fused silica polished surfaces. Luminescence cartographies are made to show the spatial distribution of each kind of defect. Three bands, centered at 1.89 eV, 2.75 eV and 2.25 eV are evidenced on laser damage and indentations. The band centered at 2.25 eV was not previously reported in photo luminescence experiments on indentations and pristine silica, for excitation wavelengths of 325 nm or larger. The luminescent objects, expected to be trapped in sub-surface micro-cracks, are possibly involved in the first step of the laser damage mechanism when fused silica is enlightened at 351 nm laser in nanosecond regime.

Experimental demonstration of a synthetic aperture compression scheme for multi-Petawatt high-energy lasers.

We present the experimental demonstration of a subaperture compression scheme achieved in the PETAL (PETawatt Aquitaine Laser) facility. We evidence that by dividing the beam into small subapertures fitting the available grating size, the sub-beam can be individually compressed below 1 ps, synchronized below 50 fs and then coherently added thanks to a segmented mirror.

High reflection mirrors for pulse compression gratings.

We report an experimental investigation of high reflection mirrors used to fabricate gratings for pulse compression application at the wavelength of 1.053microm. Two kinds of mirrors are studied: the mixed Metal MultiLayer Dielectric (MMLD) mirrors which combine a gold metal layer with some e-beam evaporated dielectric bilayers on the top and the standard e-beam evaporated MultiLayer Dielectric (MLD) mirrors. Various samples were manufactured, damage tested at a pulse duration of 500fs. Damage sites were subsequently observed by means of Nomarski microscopy and white light interferometer microscopy. The comparison of the results evidences that if MMLD design can offer damage performances rather similar to MLD design, it also exhibits lower stresses; being thus an optimal mirror substrate for a pulse compression grating operating under vacuum.

Subsurface damage measurement of ground fused silica parts by HF etching techniques.

Detection and measurement of subsurface damage of ground optical surfaces are of major concern in the assessment of high damage thresholds fused silica optics for high power laser applications. We herein detail a new principle of SSD measurement based on the utilization of HF acid etching. We also review and compare different subsurface damage (SSD) characterization techniques applied to ground and fine ground fused silica samples. We demonstrate good concordance between the different measurements.

Imaging subsurface damage of grinded fused silica optics by confocal fluorescence microscopy.

We report an experimental investigation of fluorescence confocal microscopy as a tool to measure subsurface damage on grinded fused silica optics. Confocal fluorescence microscopy was performed with an excitation at the wavelength of 405 nm on fixed abrasive diamond grinded fused silica samples. We detail the measured fluorescence spectrums and compare them to those of oil based coolants and grinding slurries. We evidence that oil based coolant used in diamond grinding induces a fluorescence that marks the subsurface damages and eases its observation. Such residual traces might also be involved in the laser damage process.

Impact of storage induced outgassing organic contamination on laser induced damage of silica optics at 351 nm.

The impact of storage conditions on laser induced damage density at 351 nm on bare fused polished silica samples has been studied. Intentionally outgassing of polypropylene pieces on silica samples was done. We evidenced an important increase of laser induced damage density on contaminated samples demonstrating that storage could limit optics lifetime performances. Atomic Force Microscopy (AFM) and Gas Chromatography -Mass Spectrometry (GC-MS) have been used to identify the potential causes of this effect. It shows that a small quantity of organic contamination deposited on silica surface is responsible for this degradation. Various hypotheses are proposed to explain the damage mechanism. The more likely hypothesis is a coupling between surface defects of optics and organic contaminants.

Chromatism compensation of the PETAL multipetawatt high-energy laser.

High-energy petawatt lasers use series of spatial filters in their amplification section. The refractive lenses employed introduce longitudinal chromatism that can spatially and temporally distort the ultrafast laser beam after focusing. To ensure optimum performances of petawatt laser facilities, these distortions need to be corrected. Several solutions using reflective, refractive, or diffractive optical components can be addressed. We give herein a review of these various possibilities with their application to the PETAL (Petawatt Aquitaine Laser at the Laser Integration Line facility) laser beamline and show that diffractive-based corrections appear to be the most promising.

Delay interferometric single shot measurement of a petawatt-class laser longitudinal chromatism corrector.

In this paper we present a self-referenced interferometric single-shot measurement technique that we use to evaluate the longitudinal chromatism compensation made by a diffractive lens corrector. A diffractive lens with a delay of 1 ps is qualified for a 60 mm beam aperture. This corrector was implemented on the Alisé Nd:glass power chain. We qualify the corrector and the Alisé power chain chromatism, demonstrating the potential of this measuring principle as well as the interest of diffractive lenses to correct longitudinal chromatism of petawatt-class lasers.

Effect of electric field on laser induced damage threshold of multilayer dielectric gratings.

This paper studies gratings engraved in multilayer dielectric stacks for ultra high intensity laser compressors application. We design various grating profiles with high reflected efficiencies for 1780 l/mm multilayer dielectric gratings (MLD). Each grating is defined to exhibit a different electric field maximum value in the pillars of the grating. A damage testing facility operating at 1.053 mum, 500 fs pulse duration is used to damage test the parts manufactured from these designs. It is evidenced that for fixed incident angle and materials the damage of the grating is directly related to the electric field intensity maximum in the material, which depends on the groove profile. Laser induced damage thresholds of 5 J/ cm(2) are experimentally reached with very high and uniform efficiencies.

Synthetic aperture compression scheme for a multipetawatt high-energy laser.

High-energy petawatt lasers using the chirped-pulse amplification technique require meter-sized gratings to limit the beam fluence on the surface of the grating. An alternative, studied by many groups, is a mosaic grating consisting of smaller, coherently added gratings. We propose what we believe to be a new compression scheme consisting of beam phasing instead of grating mosaic phasing. This synthetic aperture compression scheme allows us to control the beam thanks to a unique segmented mirror equipped with three degrees of freedom. With this configuration, the beam is divided into small subapertures adapted to the classical grating size. After compression, these subapertures are coherently added before the focusing stage. Therefore the alignment processes are simplified.

Polishing-induced contamination of fused silica optics and laser induced damage density at 351 nm.

In this paper we study the effect of contamination induced by fabrication process on laser damage density of fused silica polished parts at 351 nm in nanosecond regime. We show, owing to recent developments of our raster scan metrology, that a good correlation exists between damage density and concentration of certain contaminants for the considered parts.