Stress on external hexagon and Morse taper implants submitted to immediate loading.

BACKGROUND/AIMS: This study aimed to evaluate the stress distribution around external hexagon (EH) and Morse taper (MT) implants with different prosthetic systems of immediate loading (distal bar (DB), casting technique (CT), and laser welding (LW)) by using photoelastic method. METHODS: Three infrastructures were manufactured on a model simulating an edentulous lower jaw. All models were composed by five implants (4.1 mm × 13.0 mm) simulating a conventional lower protocol. The samples were divided into six groups. G1: EH implants with DB and acrylic resin; G2: EH implants with titanium infrastructure CT; G3: EH implants with titanium infrastructure attached using LW; G4: MT implants with DB and acrylic resin; G5: MT implants with titanium infrastructure CT; G6: MT implants with titanium infrastructure attached using LW. After the infrastructures construction, the photoelastic models were manufactured and a loading of 4.9 N was applied in the cantilever. Five pre-determined points were analyzed by Fringes software. RESULTS: Data showed significant differences between the connection types (p < 0.0001), and there was no significant difference among the techniques used for infrastructure. CONCLUSION: The reduction of the stress levels was more influenced by MT connection (except for CT). Different bar types submitted to immediate loading not influenced stress concentration.

Photoelastic analysis of stresses transmitted by complete dentures lined with hard or soft liners.

Stresses transmitted on the alveolar bone ridge by lined conventional complete mandibular dentures can decrease the bone absorption level. The aim of this in vitro study was to evaluate the stresses induced on the alveolar bone ridge of lined conventional complete mandibular dentures by using photoelastic analysis. One maxillary and three mandibular conventional dentures were developed for the following treatments: 1 - Unlined denture (control), 2 - Denture lined with resin-based material, and 3 - Denture lined with silicone-based material. The photoelastic analysis took place with the dentures in the position of maximum intercuspation, and the mandibular photoelastic models were axially loaded with 10 kgf (98 N). Unlined denture (control) presented stresses along the model, especially on the anterior and left lateral sides with less stresses on the right side. On the left lateral side, the denture base lined with resin-based material demonstrated similar stresses to that of the control; however, lower stresses occurred in the premolar and retromolar regions. Denture bases lined with silicone-based material showed decreased fringe orders and homogeneous distribution of induced stresses. Both lined dentures exhibited lower stresses when compared to unlined dentures. Silicone-based material provided a more homogeneous distribution of stresses.

Effect of toothbrushing, chemical disinfection and thermocycling procedures on the surface microroughness of denture base acrylic resins.

OBJECTIVE: This study verified the surface microroughness of denture acrylic resins submitted to toothbrushing, chemical disinfection and thermocycling procedures. MATERIAL AND METHODS: Samples were prepared according to conventional, microwaved and boiled resins and submitted to microroughness measurements before and after procedures using a profilometer (Ra). Data were subjected to anova and Tukey's test (5%). RESULTS: Before thermocycling, a difference was found among treatments for microwaved and boiled resins, with greater values for toothbrushing and lower values for Efferdent and hypochlorite; control was intermediate. Differences among resins were observed for treatments, with higher values for boiled resin and lower values for conventional and microwaved resins. After thermocycling, differences were found for microwaved resin, with a higher value for toothbrushing and a lower value for Efferdent and hypochlorite; control was intermediate. Tooth-brushed boiled resin presented higher values and hypochlorite lower values; control and Efferdent were intermediates. Differences among resins were seen for treatments, with higher values for boiled resin and lower values for conventional and microwaved resins. Boiled resin presented differences for toothbrushing and hypochlorite, before and after thermocycling procedures were compared. CONCLUSIONS: For microwaved and boiled resins, toothbrushing and chemical disinfection promoted different levels of surface microroughness when associated or not with thermocycling.

Correlação entre o desajuste marginal e a tensão gerada sobre os implantes / Correlation between marginal misfit and strains around implants

A indução de tensões ao implante e ao tecido ósseo peri-implantar pode ser responsável pela reabsorção tecidual e pela perda do implante. Próteses com o mínimo desajuste marginal são desejadas, acreditando-se na geração de menores valores de tensão às fixações .No entanto, não se tem certeza desta correlação, uma vez que a literatura não apresenta resultados confiáveis que venham a elucidar tal aspecto. Assim, o objetivo deste trabalho foi verificar se existe correlação entre os valores de desajuste marginal e de tensão gerados às fixações pelo parafusamento de infraestruturas implanto-retidas. Foram obtidas dez infraestruturas em titânio fundido, utilizando-se matriz metálica contendo dois implantes conectados a pilares cônicos para construções múltiplas. As infraestruturas foram aleatoriamente avaliadas quanto aos desajustes marginais mediante o teste do parafuso único e observação em microscópio ótico(120X). As tensões nas fixações foram avaliadas por extensometria. A média de desajuste marginal foi 118,07(58,61) μm e a média de tensão, 580,06 (253,93) gf.O teste de Pearson foi utilizado, mostrando não haver correlação entre desajuste marginal e tensão (-0,072),com p = 0,842. A presença e a intensidade do desajuste marginal, por si só, não são indicadores seguros no prognóstico da geração de tensões às fixações

The effect of thermal cycling on the bond strength of low-fusing porcelain to commercially pure titanium and titanium-aluminium-vanadium alloy.

OBJECTIVES: Titanium-ceramic restorations are currently used in spite of the pending problem of titanium-ceramic bonding, which has only been partially solved. In addition, some titanium-ceramic systems appear to be susceptible to thermal cycling, which can cause weaker bond strength. The objective of this study was to evaluate the bonding characteristics of titanium porcelain bonded to commercially pure titanium (Ti-Cp) or titanium-aluminum-vanadium (Ti-6Al-4V) alloy as well as the effect of thermal cycling on bond strength. METHODS: A three-point-flexure-test was used to evaluate the bond strength of titanium porcelain bonded to commercially pure titanium and Ti-6Al-4V alloy according to DIN 13.927. To evaluate the effect of thermal cycling on the samples, half were thermal cycled in temperatures ranging from 4 degrees C (+/-2 degrees C) to 55 degrees C (+/-2 degrees C). Results were compared with palladium-silver (Pd-Ag) alloy bonded to conventional porcelain (control). Scanning electron microscope (SEM) photomicrographs were taken to characterize the failed surfaces in the metal-ceramic interface. Anova and Tukey's multiple comparison tests were used to analyze the data at a 5% probability level. RESULTS: Thermal cycling did not significantly weaken the bond strength of porcelain to titanium interfaces. There was no significant difference in bond strength between commercially pure titanium (23.60 MPa for thermal cycled group and 24.99 MPa for non-thermal cycled group) and Ti-6Al-4V groups (24.98 and 25.60 MPa for thermal cycled and non-thermal cycled groups, respectively). Bond strength values for the control group (47.98 and 45.30 MPa, respectively) were significantly greater than those for commercially pure titanium and Ti-6Al-4V combinations. SIGNIFICANCE: The bond strength of low fusing porcelain bonded to cast pure titanium or Ti-6Al-4V alloy was significantly lower than the conventional combination of porcelain-Pd-Ag alloy. Thermal cycling did not affect the bond strength of any group.