Synergistic Interaction of Clusters of Iron Oxide Nanoparticles and Reduced Graphene Oxide for High Supercapacitor Performance.

Supercapacitors have been recognized as one of the more promising energy storage devices, with great potential use in portable electronics and hybrid vehicles. In this study, a composite made of clusters of iron oxide (Fe3O4-γFe2O3) nanoparticles and reduced graphene oxide (rGO) has been developed through a simple one-step solvothermal synthesis method for a high-performance supercapacitor electrode. Electrochemical assessment via cyclic voltammetry, galvanostatic charge-discharge experiments, and electrochemical impedance spectroscopy (EIS) revealed that the Fe3O4-γFe2O3/rGO nanocomposite showed much higher specific capacitance than either rGO or bare clusters of Fe3O4-γFe2O3 nanoparticles. In particular, specific capacitance values of 100 F g-1, 250 F g-1, and 528 F g-1 were obtained for the clusters of iron oxide nanoparticles, rGO, and the hybrid nanostructure, respectively. The enhancement of the electrochemical performance of the composite material may be attributed to the synergistic interaction between the layers of graphene oxide and the clusters of iron oxide nanoparticles. The intimate contact between the two phases eliminates the interface, thus enabling facile electron transport, which is key to attaining high specific capacitance and, consequently, enhanced charge-discharge time. Performance evaluation in consecutive cycles has demonstrated that the composite material retains 110% of its initial capacitance after 3000 cycles, making it a promising candidate for supercapacitors.

Effect of Laser Speed and Hatch Spacing on the Corrosion Behavior of 316L Stainless Steel Produced by Selective Laser Melting.

In this work, the corrosion properties of 316L stainless steel (SS) obtained by selective laser melting (SLM) are analyzed. The electrochemical results of samples manufactured with an energy density between 40 and 140 J/mm3 are compared using different hatch distances and laser speeds. The analysis correlates the impact of the microstructure and processing defects of SLM 316L stainless steel on its behavior against corrosion. The optimal manufacturing conditions were selected considering the electrochemical results. Although the samples obtained with an energy density close to 90 J/mm3 show a high resistance to corrosion, their performance depends on the combination of selected parameters, obtaining the best results for an intermediate laser speed and a low hatch distance. These manufacturing conditions produce a higher breakdown potential, a faster repassivation of the steel and reduce the current density on electrochemical test.

Laser-Guided Corrosion Control: A New Approach to Tailor the Degradation of Mg-Alloys.

Despite corrosion being commonly seen as a problem to be avoided, applications such as batteries or biodegradable implants do benefit from corrosion-like phenomena. However, current strategies address corrosion control from a global perspective for a whole component, without considering local adaptations to functionality specifications or inhomogeneous environments. Here, a novel concept is presented: the local control and guidance of corrosion through a laser surface treatment. Immersion tests in saline solution of AZ31 magnesium alloy samples show degradation rates reduced up to 15 times with the treatment, owing to a fast passivation after the induced microstructural modifications. By controlling the treatment conditions, the degradation can be restricted to delimited regions and driven towards specific directions. The applicability of the method for the design of tailored degradation biomedical implants is demonstrated and uses for cathodic protection systems and batteries can also be anticipated.

Alternating current measurements in scanning electrochemical microscopy, part 2: detection of adsorbates.

A scanning electrochemical microscope (SECM) in ac mode is used for the characterisation of the adsorption process during the hydrogen evolution reaction (HER) in sulfuric acid solution. It is shown that this technique allows quantitative analysis of the adsorption process, and measurements of the differential capacitance with the frequency as parameter are obtained. The time constant for relaxation of adsorbed hydrogen (H(ads)) is approximately 2 Hz, and analysis of the Nyquist plot allows direct evaluation of the charge involved. In addition, the direct comparison of the usual electrochemical impedance data and ac-SECM results obtained simultaneously permits characterisation of processes occurring at the surface and in solution.