Temperature dependence of charge transport in solid-state molecular junctions based on oligo(phenylene ethynylene)s.

The ultimate goal of molecular electronics is to achieve practical applications. For approaching the target, we have successfully fabricated solid-state junctions based on oligo(phenylene ethynylene)s (OPEs) and cruciform OPEs with extended tetrathiafulvalene (TTF) (OPE3 and OPE3-TTF) self-assembled monolayers (SAMs) with a diamine anchoring group. SAMs were confined in micropores with gold substrates to ensure well-defined device surface areas. The transport properties were conducted on a double-junction layout, which the rGO films used for top contacts and interconnects between adjacent SAMs. The solid-state devices based on OPE3-TTF SAMs showed the expected higher conductance under ambient conditions because of the incorporation of a TTF moiety. The two devices displayed varying degrees of temperature dependence with decreasing temperature, which resulted from the cross-conjugated OPE3-TTF molecule exhibiting quantum interference while the linear-conjugated OPE3 molecule did not. This study shows the temperature dependence of the electrical properties of molecular devices based on cruciform OPEs, further enriching the research results of functional molecular devices.

In-Place Modulation of Rectification in Tunneling Junctions Comprising Self-Assembled Monolayers.

This paper describes tunneling junctions comprising self-assembled monolayers that can be converted between resistor and diode functionality in-place. The rectification ratio is affected by the hydration of densely packed carboxylic acid groups at the interface between the top-contact and the monolayer. We studied this process by treatment with water and a water scavenger using three different top-contacts, eutectic Ga-In (EGaIn), conducting-probe atomic force microscopy (CP-AFM), and reduced graphene oxide (rGO), demonstrating that the phenomena is molecular in nature and is not platform-speciffc. We propose a mechanism in which the tunneling junctions convert to diode behavior through the lowering of the LUMO, which is suffcient to bring it close to resonance at positive bias, potentially assisted by a Stark shift. This shift in energy is supported by calculations and a change in polarization observed by X-ray photoelectron spectroscopy and Kelvin probe measurements. We demonstrate light-driven modulation using spiropyran as a photoacid, suggesting that any chemical process that is coupled to the release of small molecules that can tightly bind carboxylic acid groups can be used as an external stimulus to modulate rectification. The ability to convert a tunneling junction reversibly between a diode and a resistor via an effect that is intrinsic to the molecules in the junction extends the possible applications of Molecular Electronics to reconfigurable circuits and other new functionalities that do not have direct analogs in conventional semiconductor devices.

Dry Chemistry of Ferrate(VI): A Solvent-Free Mechanochemical Way for Versatile Green Oxidation.

The +6 oxidation state of iron generally exists in the form of ferrate(VI) with high redox potential and environmentally friendly nature. Although ferrate(VI) has been known for over a century, its chemistry is still limited to the solvent-based reactions that suffers from the insolubility/instability of this oxidant and the environmental issues caused by hazardous solvents. Herein, we explore the solvent-free reactivity of ferrate(VI) under mechanical milling, revealing that its strong oxidizing power is accessible in the "dry" solid state towards a broad variety of substrates, for example, aromatic alcohols/aldehydes and carbon nanotubes. More significantly, solvent-free mechanochemistry also reshapes the oxidizing ability of ferrate(VI) due to the underlying solvent-free effect and the promotive mechanical actions. This study opens up a new chemistry of ferrate(VI) with promising application in green oxidative transformation of both organic and inorganic substrates.

Graphene Oxide: A One- versus Two-Component Material.

The structure of graphene oxide (GO) is a matter of discussion. While established GO models are based on functional groups attached to the carbon framework, another frequently used model claims that GO consists of two components, a slightly oxidized graphene core and highly oxidized molecular species, oxidative debris (OD), adsorbed on it. Those adsorbents are claimed to be the origin for optical properties of GO. Here, we examine this model by preparing GO with a low degree of functionalization, combining it with OD and studying the optical properties of both components and their combination in an artificial two-component system. The analyses of absorption and emission spectra as well as lifetime measurements reveal that properties of the combined system are distinctly different from those of GO. That confirms structural models of GO as a separate oxygenated hexagonal carbon framework with optical properties governed by its internal structure rather than the presence of OD. Understanding the structure of GO allows further reliable interpretation of its optical and electronic properties and enables controlled processing of GO.

Gold nanoparticles assembled with dithiocarbamate-anchored molecular wires.

A protocol for the bottom-up self-assembly of nanogaps is developed through molecular linking of gold nanoparticles (AuNPs). Two π-conjugated oligo(phenylene ethynylene) molecules (OPE) with dithiocarbamate anchoring groups are used as ligands for the AuNPs. OPE-4S with a dithiocarbamate in each end of the molecule and a reference molecule OPE-2S with only a single dithiocarbamate end group. The linking mechanism of OPE-4S is investigated by using a combination of TEM, UV-Vis absorption and surface enhanced Raman spectroscopy (SERS) as well as studying the effect of varying the OPE-4S to AuNP concentration ratio. UV-Vis absorption confirms the formation of AuNP aggregates by the appearance of an extended plasmon band (EPB) for which the red shift and intensity depend on the OPE-4S:AuNP ratio. SERS confirms the presence of OPE-4S and shows a gradual increase of the signal intensity with increasing OPE-4S:AuNP ratios up to a ratio of about 4000, after which the SERS intensity does not increase significantly. For OPE-2S, no linking is observed below full coverage of the AuNPs indicating that the observed aggregate formation at high OPE-2S:AuNP ratios, above full AuNP coverage, is most likely of a physical nature (van der Waals forces or π-π interactions).

Role of redox centre in charge transport investigated by novel self-assembled conjugated polymer molecular junctions.

Molecular electronics describes a field that seeks to implement electronic components made of molecular building blocks. To date, few studies have used conjugated polymers in molecular junctions despite the fact that they potentially transport charge more efficiently than the extensively investigated small-molecular systems. Here we report a novel type of molecular tunnelling junction exploring the use of conjugated polymers, which are self-assembled into ultrathin films in a distinguishable 'planar' manner from the traditional vertically oriented small-molecule monolayers. Electrical measurements on the junctions reveal molecular-specific characteristics of the polymeric molecules in comparison with less conjugated small molecules. More significantly, we decorate redox-active functionality into polymeric backbones, demonstrating a key role of redox centre in the modulation of charge transport behaviour via energy level engineering and external stimuli, and implying the potential of employing tailor-made polymeric components as alternatives to small molecules for future molecular-scale electronics.

A comprehensive study of extended tetrathiafulvalene cruciform molecules for molecular electronics: synthesis and electrical transport measurements.

Cruciform-like molecules with two orthogonally placed π-conjugated systems have in recent years attracted significant interest for their potential use as molecular wires in molecular electronics. Here we present synthetic protocols for a large selection of cruciform molecules based on oligo(phenyleneethynylene) (OPE) and tetrathiafulvalene (TTF) scaffolds, end-capped with acetyl-protected thiolates as electrode anchoring groups. The molecules were subjected to a comprehensive study of their conducting properties as well as their photophysical and electrochemical properties in solution. The complex nature of the molecules and their possible binding in different configurations in junctions called for different techniques of conductance measurements: (1) conducting-probe atomic force microscopy (CP-AFM) measurements on self-assembled monolayers (SAMs), (2) mechanically controlled break-junction (MCBJ) measurements, and (3) scanning tunneling microscopy break-junction (STM-BJ) measurements. The CP-AFM measurements showed structure-property relationships from SAMs of series of OPE3 and OPE5 cruciform molecules; the conductance of the SAM increased with the number of dithiafulvene (DTF) units (0, 1, 2) along the wire, and it increased when substituting two arylethynyl end groups of the OPE3 backbone with two DTF units. The MCBJ and STM-BJ studies on single molecules both showed that DTFs decreased the junction formation probability, but, in contrast, no significant influence on the single-molecule conductance was observed. We suggest that the origins of the difference between SAM and single-molecule measurements lie in the nature of the molecule-electrode interface as well as in effects arising from molecular packing in the SAMs. This comprehensive study shows that for complex molecules care should be taken when directly comparing single-molecule measurements and measurements of SAMs and solid-state devices thereof.

Triazatriangulene as binding group for molecular electronics.

The triazatriangulene (TATA) ring system was investigated as a binding group for tunnel junctions of molecular wires on gold surfaces. Self-assembled monolayers (SAMs) of TATA platforms with three different lengths of phenylene wires were fabricated, and their electrical conductance was recorded by both conducting probe-atomic force microscopy (CP-AFM) and scanning tunneling microscopy (STM). Similar measurements were performed for phenylene SAMs with thiol anchoring groups as references. It was found that, despite the presence of a sp(3) hybridized carbon atom in the conduction path, the TATA platform displays a contact resistance only slightly larger than the thiols. This surprising finding has not been reported before and was analyzed by theoretical computations of the transmission functions of the TATA anchored molecular wires. The relatively low contact resistance of the TATA platform along with its high stability and directionality make this binding group very attractive for molecular electronic measurements and devices.

Mono- and bis(pyrrolo)tetrathiafulvalene derivatives tethered to C60: synthesis, photophysical studies, and self-assembled monolayers.

A series of mono- (MPTTF) and bis(pyrrolo)tetrathiafulvalene (BPTTF) derivatives tethered to one or two C60 moieties was synthesized and characterized. The synthetic strategy for these dumbbell-shaped compounds was based on a 1,3-dipolar cycloaddition reaction between aldehyde-functionalized MPTTF/BPTTF derivatives, two different tailor-made amino acids, and C60. Electronic communication between the MPTTF/BPTTF units and the C60 moieties was studied by a variety of techniques including cyclic voltammetry and absorption spectroscopy. These solution-based studies indicated no observable electronic communication between the MPTTF/BPTTF units and the C60 moieties. In addition, femtosecond and nanosecond transient absorption spectroscopy revealed, rather surprisingly, that no charge transfer from the MPTTF/BPTTF units to the C60 moieties takes place on excitation of the fullerene moiety. Finally, it was shown that the MPTTF-C60 and C60-BPTTF-C60 dyad and triad molecules formed self-assembled monolayers on a Au(111) surface by anchoring to C60.

Wet chemical synthesis of soluble gold nanogaps.

A central challenge in molecular electronics is to create electrode pairs separated by only a few nanometers that can accommodate a single molecule of interest to be optically or electrically characterized while residing in the gap. Current techniques for nanogap fabrication are largely based on top-down approaches and often rely on subsequent deposition of molecules into the nanogap. In such an approach, the molecule may bridge the gap differently with each experiment due to variations at the metal-molecule interface. Conversely, chemists can readily synthesize gold nanorods (AuNRs) in aqueous solution. Through controlled end-to-end assembly of the AuNRs into dimers or chains, facilitated via target molecules, they can be used as electrical contacts. In this way, the preparation of AuNR-molecule-AuNR junctions by wet chemical methods may afford a large number of identical devices with little variation in the interface between molecule and electrode (AuNR). In this Account, we highlight recent progress in using chemically synthesized AuNRs as building blocks for molecular electronic applications. We outline the general synthesis and properties of AuNRs and describe the aqueous growth of dimeric AuNR structures from an insulating molecule linked to AuNR precursors (gold seeds). Conjugated, electronically active molecules are typically not soluble under the conditions required for the bottom-up growth of AuNRs. Therefore, we present a strategy that utilizes host-guest chemistry in order to make such π-systems compatible with the AuNR growth procedure. In order to electrically characterize the AuNR-molecule-AuNR constructs, we must transfer them onto a substrate and contact external electrodes. We discuss the implications of using electron-beam lithography for making this contact. In addition, we introduce a novel fabrication approach in which we can grow AuNR nanogap electrodes in situ on prepatterned substrates, thus circumventing post-processing steps that potentially damage the nanogap environment. Due to the inherent optical properties of AuNRs, electromagnetic field enhancement in the nanogaps lets us spectroscopically characterize the molecules via surface-enhanced Raman scattering. We discuss the incorporation of oligopeptides functionalized with acetylene units having uniquely identifiable vibrational modes. This acetylene moiety allows chemical reactions to be performed in the gaps via click chemistry, and the oligopeptide linking platform opens for integration of larger biological components.

A clamp-like biohybrid catalyst for DNA oxidation.

In processive catalysis, a catalyst binds to a substrate and remains bound as it performs several consecutive reactions, as exemplified by DNA polymerases. Processivity is essential in nature and is often mediated by a clamp-like structure that physically tethers the catalyst to its (polymeric) template. In the case of the bacteriophage T4 replisome, a dedicated clamp protein acts as a processivity mediator by encircling DNA and subsequently recruiting its polymerase. Here we use this DNA-binding protein to construct a biohybrid catalyst. Conjugation of the clamp protein to a chemical catalyst with sequence-specific oxidation behaviour formed a catalytic clamp that can be loaded onto a DNA plasmid. The catalytic activity of the biohybrid catalyst was visualized using a procedure based on an atomic force microscopy method that detects and spatially locates oxidized sites in DNA. Varying the experimental conditions enabled switching between processive and distributive catalysis and influencing the sliding direction of this rotaxane-like catalyst.

Ultrathin reduced graphene oxide films as transparent top-contacts for light switchable solid-state molecular junctions.

A new type of solid-state molecular junction is introduced, which employs reduced graphene oxide as a transparent top contact that permits a self-assembled molecular monolayer to be photoswitched in situ, while simultaneously enabling charge-transport measurements across the molecules. The electrical switching behavior of a less-studied molecular switch, dihydroazulene/vinylheptafulvene, is described, which is used as a test case.

A new class of extended tetrathiafulvalene cruciform molecules for molecular electronics with dithiafulvene-4,5-dithiolate anchoring groups.

Cruciform motifs with two orthogonally oriented π-extended tetrathiafulvalenes and with differently protected thiolate end-groups are synthesized by stepwise coupling reactions. The molecules are subjected to single-molecule conductivity studies in a break-junction and to conducting probe atomic force microscopy studies in a self-assembled monolayer on gold.

Electrical annealing and temperature dependent transversal conduction in multilayer reduced graphene oxide films for solid-state molecular devices.

The transversal conductance through thin multi-layered films of reduced graphene oxide was studied as a function of temperature in a solid-state device setup designed for molecular electronic measurements. Upon cooling to cryogenic temperatures, the resistivity of the films increased by about three orders of magnitude compared to the value at room temperature, and this temperature dependence was described by a variable range hopping model. Above a certain threshold voltage the films could be annealed electrically at low temperatures. This electrical annealing resulted in a dramatic decrease in resistivity by up to four orders of magnitude. Upon reheating, the conductivity of the annealed films displayed an almost negligible temperature dependence. These results are promising for the application of reduced graphene oxide as a soft top-contact layer for molecular monolayer devices in the solid-state.

End-to-end assembly of gold nanorods via oligopeptide linking and surfactant control.

We report two novel approaches for fabricating self-assembled chains of end-to-end linked Au nanorods separated by a nanogap. In one approach, bi-functional cysteine end-capped oligopeptides of different lengths are used as the linking agent. The widths of the produced nanogaps scale with the length and tertiary structure of the peptide linker. Functionalized oligopeptides containing an acetylene group are also employed as a linker, and the functional group is uniquely identified using surface-enhanced Raman spectroscopy. The development of an oligopeptide-linking platform is motivated by the ease of synthesis and high modularity of peptides; these features enable the possibility to integrate diverse functionality into molecular nanogap junctions - synthesized in water. The stepwise nanochain formation is followed via the evolution of the longitudinal plasmon absorption band in combination with transmission electron microscopy. The reaction rate and extent is tuned by controlling the concentration of the stabilizing CTAB surfactant in the solution. At very low surfactant concentrations, spontaneous end-to-end linking of the Au nanorods is observed even in the absence of linking peptide. The assembled AuNRs may act as next-generation electrodes in a platform for molecular electronics and synthetic biology.

Aligned growth of gold nanorods in PMMA channels: parallel preparation of nanogaps.

We demonstrate alignment and positional control of gold nanorods grown in situ on substrates using a seed-mediated synthetic approach. Alignment control is obtained by directing the growth of spherical nanoparticle seeds into nanorods in well-defined poly(methyl methacrylate) nanochannels. Substrates with prepatterned metallic electrodes provide an additional handle for the position of the gold nanorods and yield nanometer-sized gaps between the electrode and nanorod. The presented approach is a novel demonstration of bottom-up device fabrication of multiple nanogap junctions on a single chip mediated viain situ growth of gold nanorods acting as nanoelectrodes.

Solution-processed ultrathin chemically derived graphene films as soft top contacts for solid-state molecular electronic junctions.

A novel method using solution-processed ultrathin chemically derived graphene films as soft top contacts for the non-destructive fabrication of molecular junctions is demonstrated. We believe this protocol will greatly enrich the solid-state test beds for molecular electronics due to its low-cost, easy-processing and flexible nature.

Molecular junctions based on SAMs of cruciform oligo(phenylene ethynylene)s.

Cruciform oligo(phenylene ethynylene)s (OPEs) with an extended tetrathiafulvalene (TTF) donor moiety (OPE5-TTF and OPE3-TTF) and their simple analogues (OPE5-S and OPE3) without conjugated substituents were used to form high-quality self-assembled monolayers (SAMs) on ultraflat gold substrates. Molecular junctions based on these SAMs were investigated using conducting-probe atomic force microscopy (CP-AFM). The TTF substituent changes the molecular orbital energy levels and decreases the HOMO-LUMO energy gap, resulting in a 9-fold increase in conductance for both TTF cruciform OPEs compared to the unsubstituted analogues. The difference in electrical transport properties of the SAMs was reproduced by the theoretical transport calculations for the single molecules.

Close columnar packing of triangulenium ions in Langmuir films.

Three new tris(dialkylamino)trioxatriangulenium (ATOTA+) salts rendered amphiphilic by attachment of two (5a x PF6 and 5b x PF6) or four (5c x PF6) n-decyl chains have been synthesized, and their Langmuir films have been studied by grazing incidence X-ray diffraction (GIXD). Compounds 5a x PF6 and 5b x PF6 both self-assemble into 2D-crystalline Langmuir monolayers, in which the planar triangular shaped carbenium ions form columnar aggregates segregated from the PF6- ions. The column width is found to be close to the width of the triangulenium moiety itself (approximately 17 angstroms), while the repeat distance along the columnar aggregates is only 3.45 angstroms, implicating a near cofacial columnar structure with only a small tilt of the planar carbenium ions relative to the columnar axis. A detailed Bragg rod analysis confirmed an 8-9 degrees tilt and inferred a large anisotropy in the smearing/thermal displacement along the pi-pi stacking and lamellar packing directions. Specular X-ray reflectivity (SXR) was used to confirm the model derived from the GIXD data and elucidate the average position of the disordered PF6- ions, showing that the majority of the anions are accommodated in the ATOTA+ layer rather than in the water subphase.