ABSTRACT
OBJECTIVES: The aim of this study was to compare intaglio surface adaptation of the removable partial denture framework among various data acquisition techniques and fabrication approaches using three-dimensional comparison by metrology software. MATERIALS AND METHODS: The partial edentulous typodont model with five digital superimposition landmarks was duplicated and scanned for the digital reference model. Three approaches were the conventional lost-wax (group I; LWT, n = 5), intraoral digital impressions combined with PolyJet printing and lost-wax (group II; IP-LWT, n = 5), and extraoral digital impressions combined with PolyJet printing and lost-wax (group III; EP-LWT, n = 5). Each framework was scanned and superimposed with the reference model. The misfits at 53 locations were measured. STATISTICAL ANALYSIS: Data were statistically analyzed by one-way analysis of variance, followed by Tukey's honestly significant difference for pairwise comparisons (p < 0.05). RESULTS: Significant differences were found between three approaches at the reciprocal arm, terminal part of the retentive arm, rest, and major connector (p < 0.05). In the LWT group, the reciprocal arm and palatal vault region of major connector had the lowest misfits, but the highest misfit was found in the midline region (p < 0.001). In the IP-LWT group revealed the most excessive contact at the terminal part of the retentive arm (-0.111 ± 0.038 mm, p = 0.031), with the highest misfit at the rest area (p < 0.001). CONCLUSION: A difference in adaptation was found in several removable partial denture framework components among three approaches. The LWT group had a better adaptation than other groups. Nevertheless, a clinically acceptable adaptation was seen in all three approaches.
ABSTRACT
This study assessed the use of the commercial artificial teeth setup device Staub Cranial System (Neu-Ulm) in Asian subjects. Fourteen completely dentate Thai volunteers were randomly recruited. Study casts (control group) and duplicated casts (experimental group) of all subjects were prepared. Artificial teeth were replaced on duplicated casts according to the manual. Computed tomography scans of all casts were performed. Intercanine width, intermolar width, incisocervical length, and occlusal plane were investigated. The length of the natural mandibular left central incisor was smaller than the reconstructed one. The reconstructed occlusal plane was more parallel to the hamular-incisive papilla plane than that of the control group.
Subject(s)
Models, Theoretical , Tooth, Artificial , Humans , Tomography, X-Ray ComputedABSTRACT
PURPOSE: Zirconia has been used in clinical dentistry for approximately a decade, and there have been several reports regarding the clinical performance and survival rates of zirconia-based restorations. The aim of this article was to review the literatures published from 2000 to 2010 regarding the clinical performance and the causes of failure of zirconia fixed partial dentures (FPDs). MATERIALS AND METHODS: An electronic search of English peer-reviewed dental literatures was performed through PubMed to obtain all the clinical studies focused on the performance of the zirconia FPDs. The electronic search was supplemented by manual searching through the references of the selected articles for possible inclusion of some articles. Randomized controlled clinical trials, longitudinal prospective and retrospective cohort studies were the focuses of this review. Articles that did not focus on the restoration of teeth using zirconia-based restorations were excluded from this review. RESULTS: There have been three studies for the study of zirconia single crowns. The clinical outcome was satisfactory (acceptable) according to the CDA evaluation. There have been 14 studies for the study of zirconia FPDs. The survival rates of zirconia anterior and posterior FPDs ranged between 73.9% - 100% after 2 - 5 years. The causes of failure were veneer fracture, ceramic core fracture, abutment tooth fracture, secondary caries, and restoration dislodgment. CONCLUSION: The overall performance of zirconia FPDs was satisfactory according to either USPHS criteria or CDA evaluations. Fracture resistance of core and veneering ceramics, bonding between core and veneering materials, and marginal discrepancy of zirconia-based restorations were discussed as the causes of failure. Because of its repeated occurrence in many studies, future researches are essentially required to clarify this problem and to reduce the fracture incident.
