Pd "Kills Two Birds with One Stone" for the Synthesis of Catalyst: Dual Active Sites of Pd Triggers the Kinetics of O2 Electrocatalysis.

Noble metal-based catalyst, despite their exorbitant cost, are the only successful catalyst for bifunctional oxygen electrocatalysis owing to their capability to drive forward the reaction rate kinetically. Therefore, it is desirable to diminish the noble metal loading without any compromise in the catalyst performance. In this study, the aim to achieve two goals with one action via a single-step route to have ultra-low loading of Pd in the catalyst. The Pd is used as a catalyst for C─C bond formation followed by complexation reactions or vice versa, in conventional Suzuki-Miyaura cross-coupling (SMCC) reaction, which yields a Pd-based porous organic polymer. Interestingly, it is found that dispersed Pd nanocluster (PdNC ) is present together with Pd single atom doped into nanocarbon (Pd-NC) matrix in the catalyst (PdNC /Pd-NC800 ) that obtained after pyrolysis of the porous polymer. The catalyst exhibits remarkable bifunctional activity and durability towards oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). Further, it is studied that the in situ attenuated total reflection infrared (ATR-IR) spectroscopy at different electrochemical potentials during ORR and OER to observe the reaction intermediates. The homemade zinc-air battery with the catalyst displayed great performance, establishing the significance of PdNC /Pd-NC800 as a bifunctional oxygen electrocatalyst.

Controlled synthesis of Ru-single-atoms on ordered mesoporous phosphine polymers for microwave-assisted conversion of biomass-derived sugars to artificial sweeteners.

Atomically dispersed metal-single-atoms have become a frontier in solid catalysis due to their characteristic electronic properties. However, for biomass conversion, employing metal-single-atoms as catalysts is rather challenging since they suffer from poor selectivity and yield due to inadequate metal-support interactions. We show here that Ru/triphenylphosphine (PPh)-based ordered mesoporous polymers afford high yields of reduced sugars, xylitol (yield ∼95%) and sorbitol (yield ∼65%) in a microwave reactor with formic acid as the only hydrogen donor. We have established a unique relationship within Ru/triphenylphosphine that shows an important ligand effect, in contrast to, Ru/triphenylamine and Ru/catechol. The tailored electronic properties in Ru/phosphine were thoroughly examined by using state-of-the-art experimental techniques viz. EXAFS, XANES, XPS, DRIFTS and HAADF-STEM. The resulting phosphine-modified catalysts show a promotion in activity and selectivity towards less vulnerable aldehydes for hydrogenation, further confirmed by DFT calculations. This finding reveals a new protocol to tailor the activity of metal-single-atoms utilizing functional porous polymers as nanoreactors.

Anisotropic phenanthroline-based ruthenium polymers grafted on a titanium metal-organic framework for efficient photocatalytic hydrogen evolution.

Conjugated polymers and titanium-based metal-organic framework (Ti-MOF) photocatalysts have demonstrated promising features for visible-light-driven hydrogen production. We report herein a strategy of anisotropic phenanthroline-based ruthenium polymers (PPDARs) over Ti-MOF, a tunable platform for efficient visible-light-driven photocatalytic hydrogen evolution reaction (HER). Several analytical methods including X-ray absorption spectroscopy (XAS) revealed the judicious integration of the surface-active polymer over the Ti-MOF reinforcing the catalytic activity over the broad chemical space. PPDAR-4 polyacrylate achitecture led to a substantial increase in the H2 evolution rate of 2438 µmolg-1h-1 (AQY: 5.33%) compared to pristine Ti-MOF (238 µmol g-1 h-1). The separation of photogenerated charge carriers at the PPDAR-4/Ti-MOF interface was confirmed by the optical and electrochemical investigations. The experimental, as well as theoretical data, revealed their physical and chemical properties which are positively correlated with the H2 generation rate. This offers a new avenue in creating polymer-based MOF robust photocatalysts for sustainable energy.

Identification of a copper ion recognition peptide sequence in the subunit II of cytochrome c oxidase: a combined theoretical and experimental study.

The role of the pentapeptide, NHSFM, derived from the surface exposed part of the metal ion binding loop of the subunit II of cytochrome c oxidase on the maturation of the binuclear purple CuA center of the enzyme has been investigated using several experimental and computational methods. The copper ion was found to form 1:1 complex of the pentapeptide with a binding constant ~ 104 M-1 to 105 M-1, where a 4 ligand coordination from the peptide in a type 2 copper center was revealed. The pH dependence of the metal-peptide was associated with a [Formula: see text] of ~ 10 suggesting deprotonation of the N-terminal amine. EXAFS studies as well as DFT calculations of the metal-peptide complexes revealed pH dependent changes in the metal-ligand bond distances. Spectroscopic properties of the metal peptides calculated from TDDFT studies agreed with the experimental results. Restrained molecular dynamics (RMD) simulations indicated coordination of a carbonyl oxygen from the asparagine (N) side chain and of water molecules apart from histidine (H), methionine (M) and terminal amine of asparagine (N) in a distorted square planar geometry of Cu-NHSFM. Analyses of the backbone distances as well as B-factors for the metal peptide suggested that the peptide backbone becomes more compact and rigid on binding of the metal ion. This indicated that binding of copper ion to this pentapeptide in the protein possibly cause movement of the protein backbone bringing other coordinating residues closer to the copper ion, and thus helping in sequential uptake of copper ions to the protein.

Colloidal BaZrS3 chalcogenide perovskite nanocrystals for thin film device fabrication.

The theoretical optoelectronic properties of chalcogenide perovskites (e.g., BaZrS3) are as good as those of halide perovskites (e.g., CH3NH3PbI3). But the fabrication of optoelectronic devices is rarely reported, mainly because researchers still do not know how to prepare good quality thin films of chalcogenide perovskites. Here, we report colloidal BaZrS3 nanocrystals (NCs, 40-60 nm) and their solution processed thin film transistors. BaZrS3 NCs are first prepared using a solid-state synthesis route, and the subsequent surface modifications lead to a colloidal dispersion of NCs in both polar N-methyl-2-pyrrolidinone and non-polar chloroform solvents. The NCs exhibit good thermal (15-673 K) and aqueous stability. Colloidal BaZrS3 NCs in chloroform are then used to make field effect transistors showing ambipolar properties with a hole mobility of 0.059 cm2 V-1 s-1 and an electron mobility of 0.017 cm2 V-1 s-1. This report of solution processed chalcogenide perovskite thin films with reasonable carrier mobility and optical absorption and emission is expected to pave the way for future optoelectronic devices of chalcogenide perovskites.

Operando X-ray absorption spectroscopy study of the Fischer-Tropsch reaction with a Co catalyst.

This article describes the setting up of a facility on the energy-scanning EXAFS beamline (BL-09) at RRCAT, Indore, India, for operando studies of structure-activity correlation during a catalytic reaction. The setup was tested by operando X-ray absorption spectroscopy (XAS) studies performed on a Co-based catalyst during the Fischer-Tropsch reaction to obtain information regarding structural changes in the catalyst during the reaction. Simultaneous gas chromatography (GC) measurements during the reaction facilitate monitoring of the product gases, which in turn gives information regarding the activity of the catalyst. The combination of XAS and GC techniques was used to correlate the structural changes with the activity of the catalyst at different reaction temperatures. The oxide catalyst was reduced to the metallic phase by heating at 400°C for 5 h under H2 at ambient pressure and subsequently the catalytic reaction was studied at four different temperatures of 240, 260, 280 and 320°C. The catalyst was studied for 10 h at 320°C and an attempt has been made to understand the process of its deactivation from the XANES and EXAFS results.

High Pressure Phases and Amorphization of a Negative Thermal Expansion Compound TaVO5.

Negative thermal expansion material TaVO5 is recently reported to have pressure induced structural phase transition and irreversible amorphization at 0.2 and above 8 GPa, respectively. Here, we have investigated the high pressure phase of TaVO5 using in situ neutron diffraction studies. The first high pressure phase is identified to be monoclinic P21/ c phase, same as the low temperature phase of TaVO5. On heating, amorphous TaVO5 transformed to a new crystalline phase, which showed signatures of higher coordination of vanadium indicating pressure induced amorphization (PIA). PIA observed in TaVO5 might be due to the kinetic hindrance of pressure induced decomposition (PID) into a compound with higher coordination of vanadium. Mechanism of PIA observed in TaVO5 is investigated by carrying out ex situ Raman, XRD, XPS, and XAS measurements. We have also proposed a pressure-temperature phase diagram of TaVO5 qualitatively delineating the phase boundaries between the ambient orthorhombic, monoclinic, and amorphous phases.

Insight into growth of Au-Pt bimetallic nanoparticles: an in situ XAS study.

Au-Pt bimetallic nanoparticles have been synthesized through a one-pot synthesis route from their respective chloride precursors using block copolymer as a stabilizer. Growth of the nanoparticles has been studied by simultaneous in situ measurement of X-ray absorption spectroscopy (XAS) and UV-Vis spectroscopy at the energy-dispersive EXAFS beamline (BL-08) at Indus-2 SRS at RRCAT, Indore, India. In situ XAS spectra, comprising both X-ray near-edge structure (XANES) and extended X-ray absorption fine-structure (EXAFS) parts, have been measured simultaneously at the Au and Pt L3-edges. While the XANES spectra of the precursors provide real-time information on the reduction process, the EXAFS spectra reveal the structure of the clusters formed in the intermediate stages of growth. This insight into the formation process throws light on how the difference in the reduction potential of the two precursors could be used to obtain the core-shell-type configuration of a bimetallic alloy in a one-pot synthesis method. The core-shell-type structure of the nanoparticles has also been confirmed by ex situ energy-dispersive spectroscopy line-scan and X-ray photoelectron spectroscopy measurements with in situ ion etching on fully formed nanoparticles.

Unusual Versatility of the Filamentous, Diazotrophic Cyanobacterium Anabaena torulosa Revealed for Its Survival during Prolonged Uranium Exposure.

Reports on interactions between cyanobacteria and uranyl carbonate are rare. Here, we present an interesting succession of the metabolic responses employed by a marine, filamentous, diazotrophic cyanobacterium, Anabaena torulosa for its survival following prolonged exposure to uranyl carbonate extending up to 384 h at pH 7.8 under phosphate-limited conditions. The cells sequestered uranium (U) within polyphosphates on initial exposure to 100 µM uranyl carbonate for 24 to 28 h. Further incubation until 120 h resulted in (i) significant degradation of cellular polyphosphates causing extensive chlorosis and cell lysis, (ii) akinete differentiation followed by (iii) extracellular uranyl precipitation. X-ray diffraction (XRD) analysis, fluorescence spectroscopy, X-ray absorption near edge structure (XANES), and extended X-ray absorption fine structure (EXAFS) spectroscopy established the identity of the bioprecipitated uranium as a U(VI) autunite-type mineral, which settled at the bottom of the vessel. Surprisingly, A. torulosa cells resurfaced as small green flakes typical of actively growing colonies on top of the test solutions within 192 to 240 h of U exposure. A consolidated investigation using kinetics, microscopy, and physiological and biochemical analyses suggested a role of inducible alkaline phosphatase activity of cell aggregates/akinetes in facilitating the germination of akinetes leading to substantial regeneration of A. torulosa by 384 h of uranyl incubation. The biomineralized uranium appeared to be stable following cell regeneration. Altogether, our results reveal novel insights into the survival mechanism adopted by A. torulosa to resist sustained uranium toxicity under phosphate-limited oxic conditions.IMPORTANCE Long-term effects of uranyl exposure in cyanobacteria under oxic phosphate-limited conditions have been inadequately explored. We conducted a comprehensive examination of the metabolic responses displayed by a marine cyanobacterium, Anabaena torulosa, to cope with prolonged exposure to uranyl carbonate at pH 7.8 under phosphate limitation. Our results highlight distinct adaptive mechanisms harbored by this cyanobacterium that enabled its natural regeneration following extensive cell lysis and uranium biomineralization under sustained uranium exposure. Such complex interactions between environmental microbes such as Anabaena torulosa and uranium over a broader time range advance our understanding on the impact of microbial processes on uranium biogeochemistry.

Nitrogen Doping in Oxygen-Deficient Ca2Fe2O5: A Strategy for Efficient Oxygen Reduction Oxide Catalysts.

Oxygen reduction reaction (ORR) is increasingly being studied in oxide systems due to advantages ranging from cost effectiveness to desirable kinetics. Oxygen-deficient oxides like brownmillerites are known to enhance ORR activity by providing oxygen adsorption sites. In parallel, nitrogen and iron doping in carbon materials, and consequent presence of catalytically active complex species like C-Fe-N, is also suggested to be good strategies for designing ORR-active catalysts. A combination of these features in N-doped Fe containing brownmillerite can be envisaged to present synergistic effects to improve the activity. This is conceptualized in this report through enhanced activity of N-doped Ca2Fe2O5 brownmillerite when compared to its oxide parents. N doping is demonstrated by neutron diffraction, UV-vis spectroscopy, X-ray photoelectron spectroscopy, and X-ray absorption spectroscopy. Electrical conductivity is also found to be enhanced by N doping, which influences the activity. Electrochemical characterization by cyclic voltammetry, rotating disc electrode, and rotating ring disk electrode (RRDE) indicates an improved oxygen reduction activity in N-doped brownmillerite, with a 10 mV positive shift in the onset potential. RRDE measurements show that the compound exhibits 4-electron reduction pathways with lower H2O2 production in the N-doped system; also, the N-doped sample exhibited better stability. The observations will enable better design of ORR catalysts that are stable and cost-effective.

An experimental and computational study to understand the lithium storage mechanism in molybdenum disulfide.

The lithium storage mechanism in molybdenum disulfide (MoS(2)) has been comprehensively investigated as the existing conversion-based storage mechanism is unable to explain the reason behind its high practical capacity, high polarization losses, and the change in the discharge profile after the 1(st) charge-discharge cycle. To resolve these issues and to gain a deeper understanding of MoS(2)-based Li-ion batteries, for the first time, we have studied the reaction mechanism of the MoS(2) anode using various experimental techniques such as XRD, Raman spectroscopy, electrochemical impedance spectroscopy, XANES, and EXAFS, as well as ab initio density functional theory based calculations. On the basis of the results presented here, and in line with some experimental findings, we find that the reaction of MoS(2) with Li is not as simple as with usual metal oxide based conversion reactions, but that the pathway of the conversion reaction changes after the first discharge process. In the first discharge process, lithiation is initiated by a limited intercalation process, followed by a conversion reaction that produces molybdenum nanoparticles (Mo) and lithium sulfide (Li(2)S). Whereas, unlike oxide-based conversion materials, MoS(2) does not transverse back during the delithiation process. Indeed, instead of MoS(2) formation, we identified the presence of polysulfur after the complete cycle. In consecutive cycles, polysulfur reacts with lithium and forms Li(2)S/Li(2)S(2), and this Li-S reaction is found to be highly reversible in nature and the only source of the high practical capacity observed in this electrode. To validate our experimental findings, an atomic scale ab initio computational study was also carried out, which likewise suggests that Li first intercalates between the MoS(2) layers but that after a certain concentration, it reacts with MoS(2) to form Li(2)S. The calculations also support the non-reversibility of the conversion reaction, by showing that Mo + Li(2)S formation is energetically more favorable than the re-formation of MoS(2) + Li.