ABSTRACT
An unusual dot pattern was realized via self-assembly of high molecular weight polystyrene-block-polydimethylsiloxane (PS-b-PDMS) copolymer by a simple one-step solvent annealing process, optimized based on Hansen solubility parameters. Annealing PS-b-PDMS under neutral solvent vapors at room temperature produces an ordered arrangement of dots with â¼112â¯nm spacing and â¼54â¯nm diameter. The template is highly resistant to dry etching with chlorine-based plasma, enabling its utilization on a variety of hard masks and substrates. The self-assembled PDMS dots were further exploited as a template for direct patterning of silicon, metal, and dielectric materials. This nanopatterning methodology circumvents expensive and time-consuming atomic layer deposition, wet processes, and sequential infiltration techniques. Application-wise, we show a process to fabricate nanostructured antireflection surfaces (nanocones) on a 2â¯in. silicon wafer, reducing the reflectance of planar silicon from 35% to below 0.5% over a broad wavelength range. Alternatively, nanocones made of TiO2 on silicon exhibit low reflectance (<3%) and improved transmittance into the substrate at the visible wavelength range. The measured optical properties concur with the simulation results. The versatility of the PS-b-PDMS templates was further utilized for nanopatterning materials such as silicon-on-insulator substrates, gallium arsenide, aluminum indium phosphide, and gallium nitride, which are important in electronics and photonics.
ABSTRACT
Adding roughness to hydrophilic surfaces is generally expected to enhance their wetting by water. Indeed, global free energy minimization predicts decreasing contact angles when roughness factor or surface energy increases. However, experimentally it is often found that water spreading on rough surfaces is impeded by pinning effects originating from local free energy minima; an effect, largely neglected in scientific literature. Here, we utilize Laplace pressure as a proxy for these local minima, and we map the transition to a superwetting state of hydrophilic nano-textured surfaces in terms of surface chemistry and texture geometry. We demonstrate the effect for polymer model surfaces templated from block-copolymer self-assembly comprising dense, nano-pillar arrays exhibiting strong pinning in their pristine state. By timed argon plasma exposure, we tune surface chemistry to map the transition into the superwetting state of low contact angle, which we show coincide with the surface supporting hemiwicking flow. For the near-ideal model surfaces, the transition to the superwetting state occurs below a critical material contact angle of â¼50°. We show that superwetting surfaces possess anti-fogging properties, and demonstrate long term stability of the superwetting effect by coating the nanotextured surfaces with â¼10 nm thin films of either tungsten or silica.
ABSTRACT
In this paper, we report on the fabrication of optical nanoresonators using block copolymer lithography. The nanostructured gratings or nanofins were fabricated using a silicon-containing block copolymer on a chromium coated silicon-on-insulator substrate. The etch resistance of the block copolymer template enables a unique patterning technique for high-aspect-ratio silicon nanofins. Integration of the directed self-assembly with nanoimprint lithography provides a well-aligned array of nanofins with a depth of â¼125 nm on a wafer scale. The developed nanopatterning method is an alternative to the previously reported nanopatterning techniques utilizing block copolymers. A dense array of sub-10 nm nanofins is used to realize a photonic guided-mode resonance filter. The nanostructured grating provides high sensitivity in refractive index sensing, as demonstrated by simulations and experiments in measuring varying contents of the tetrahydrofuran solvent.
ABSTRACT
Due to strong mode confinement, long propagation distance, and unique tunability, graphene plasmons have been widely explored in the mid-infrared and terahertz windows. However, it remains a big challenge to push graphene plasmons to shorter wavelengths to integrate graphene plasmon concepts with existing mature technologies in the near-infrared region. We investigate localized graphene plasmons supported by graphene nanodisks and experimentally demonstrate graphene plasmon working at 2 µm with the aid of a fully scalable block copolymer self-assembly method. Our results show a promising way to promote graphene plasmons for both fundamental studies and potential applications in the near-infrared window.
ABSTRACT
We report a novel nanofabrication process via block copolymer lithography using solvent vapor annealing. The nanolithography process is facile and scalable, enabling fabrication of highly ordered periodic patterns over entire wafers as substrates for surface-enhanced Raman spectroscopy (SERS). Direct silicon etching with high aspect ratio templated by the block copolymer mask is realized without any intermediate layer or external precursors. Uniquely, an atomic layer deposition (ALD)-assisted method is introduced to allow reversing of the morphology relative to the initial pattern. As a result, highly ordered silicon nanopillar arrays are fabricated with controlled aspect ratios. After metallization, the resulting nanopillar arrays are suitable for SERS applications. These structures readily exhibit an average SERS enhancement factor of above 10(8), SERS uniformities of 8.5% relative standard deviation across 4 cm, and 6.5% relative standard deviation over 5 × 5 mm(2) surface area, as well as a very low SERS background. The as-prepared SERS substrate, with a good enhancement and large-area uniformity, is promising for practical SERS sensing applications.
ABSTRACT
Nanostructured graphene exhibits many intriguing properties. For example, precisely controlled graphene nanomeshes can be applied in electronic, photonic, or sensing devices. However, fabrication of nanopatterned graphene with periodic supperlattice remains a challenge. In this work, periodic graphene nanomesh was fabricated by photocatalysis of single-layer graphene suspended on top of TiO2-covered nanopillars, which were produced by combining block copolymer nanolithography with atomic layer deposition. Graphene nanoribbons were also prepared by the same method applied to a line-forming block copolymer template. This mask-free and nonchemical/nonplasma route offers an exciting platform for nanopatterning of graphene and other UV-transparent materials for device engineering.
ABSTRACT
Block copolymer (BC) self-assembly constitutes a powerful platform for nanolithography. However, there is a need for a general approach to BC lithography that critically considers all the steps from substrate preparation to the final pattern transfer. We present a procedure that significantly simplifies the main stream BC lithography process, showing a broad substrate tolerance and allowing for efficient pattern transfer over wafer scale. PDMS-rich poly(styrene-b-dimethylsiloxane) (PS-b-PDMS) copolymers are directly applied on substrates including polymers, silicon and graphene. A single oxygen plasma treatment enables formation of the oxidized PDMS hard mask, PS block removal and polymer or graphene substrate patterning.
ABSTRACT
We present a conceptually simple approach to nanolithographic patterning utilizing ex situ fabricated nanoporous masks from block copolymers. The fabricated block copolymer (BC) masks show predictable morphology based on the correlation between BC composition and bulk properties, independent of substrates' surface properties. The masks are prepared by microtoming of prealigned nanoporous polymer monoliths of hexagonal morphology at controlled angles; they appear as 30-60 nm thick films of typical dimensions 100 µm × 200 µm. Masks cut perpendicular to the cylindrical axis show monocrystalline hexagonal packing of 10 nm pores with a principal period of 20 nm. We demonstrate the transfer of the hexagonal pattern onto silicon by means of reactive ion etching through the masks. In addition, patterns of elliptic and slit-like holes on silicon are obtained by utilizing masks cut at 45° relative to the cylinder axis. Finally, we demonstrate the first transfer of moiré patterns from block copolymer masks to substrate. The nanoporous masks prepared ex situ show outstanding long-range order and can be applied directly onto any flat substrate, eliminating the need for topographic and chemical surface modification, which are essential prerequisites for the conventional procedure of block copolymer directed self-assembly. The demonstrated elliptic and moiré pattern transfers prove that the proposed ex situ procedure allows us to realize nanolithographic patterns that are difficult to realize by the conventional approach alone.
ABSTRACT
Biofilms cause extensive damage to industrial settings. Thus, it is important to improve the existing techniques and develop new strategies to prevent bacterial biofilm formation. In the present study, we have prepared nanoporous polymer films from a self-assembled 1,2-polybutadiene-b-polydimethylsiloxane (1,2-PB-b-PDMS) block copolymer via chemical cross-linking of the 1,2-PB block followed by quantitative removal of the PDMS block. Sodium dodecyl sulfate (SDS) was loaded into the nanoporous 1,2-PB from aqueous solution. The SDS-loaded nanoporous polymer films were shown to block bacterial attachment in short-term (3 h) and significantly reduce biofilm formation in long-term (1 week) by gram-negative bacterium Escherichia coli. Tuning the thickness or surface morphology of the nanoporous polymer films allowed to extent the anti-biofilm capability.
ABSTRACT
Polymers play a central role in the development of carriers for diagnostic and therapeutic agents. Especially the use of either degradable polymers or porous materials to encapsulate drug compounds in order to obtain steady drug release profiles has received much attention. We present here a proof of principle for a system combining these two encapsulation methods and consisting of a nanoporous polymer (NP) with the pores filled with a degradable polymer mixed with a drug model. Rhodamine 6G (R6G) mixed with Poly(L-Lactic Acid) (PLLA) were confined within the 14 nm pores of a NP with gyroid morphology derived from a diblock copolymer precursor. Glass transition, crystallization and melting of free and confined PLLA were monitored by differential scanning calorimetry. Release profiles for R6G were measured in methanol-water solvents at pH 13, which works as an accelerated release test by speeding up the hydrolysis of PLLA. The obtained release profiles demonstrate that the degradation of PLLA in nanoporous confinement is significantly slower than the degradation of unconfined PLLA. The release of R6G encapsulated in PLLA becomes correspondingly slower, while the initial burst release virtually disappears. These findings suggest that the presented proof of principle constitutes a promising basis for the development of novel implantable drug delivery systems.
Subject(s)
Biocompatible Materials/chemistry , Drug Delivery Systems , Polymers/chemistry , Lactic Acid/chemistry , Microscopy, Electron, Transmission , Models, Biological , Molecular Structure , Porosity , Rhodamines/chemistryABSTRACT
Understanding the relevant permeability properties of ultrafiltration membranes is facilitated by using materials and procedures that allow a high degree of control on morphology and chemical composition. Here we present the first study on diffusion permeability through gyroid nanoporous cross-linked 1,2-polybutadiene (1,2-PB) membranes with uniform pores that, if needed, can be rendered hydrophilic. The gyroid porosity has the advantage of isotropic percolation with no need for structure prealignment. Closed (skin) or opened (nonskin) outer surface can be simply realized by altering the interface energy in the process of membrane fabrication. The morphology of the membranes' outer surface was investigated by scanning electron microscopy, contact angle, and X-ray photoelectron spectroscopy. The effective diffusion coefficient of glucose decreases from nonskin, to one-sided skin to two-sided skin membranes, much faster than expected by a naive resistance-in-series model; the flux through the two-sided skin membranes even increases with the membrane thickness. We propose a model that captures the physics behind the observed phenomena, as confirmed by flow visualization experiments. The chemistry of 1,2-PB nanoporous membranes can be controlled, for example, by hydrophilic patterning of the originally hydrophobic membranes, which allows for different active porosity toward aqueous solutions and, therefore, different permeability. The membrane selectivity is evaluated by comparing the effective diffusion coefficients of a series of antibiotics, proteins, and other biomolecules; solute permeation is discussed in terms of hindered diffusion. The combination of uniform bulk morphology, isotropically percolating porosity, controlled surface chemistry, and tunable permeability is distinctive for the presented gyroid nanoporous membranes.
Subject(s)
Membranes, Artificial , Nanopores , Nanotechnology/methods , Butadienes/chemistry , Diffusion , Dimethylpolysiloxanes/chemistry , Elastomers/chemistry , Glucose/chemistry , Hydrophobic and Hydrophilic Interactions , Permeability , Surface PropertiesABSTRACT
We present an efficient method for functionalizing the large polymer-air interface of a gyroid nanoporous polymer. The hydrophilicity of nanoporous cross-linked 1,2-polybutadiene is tuned by thiol-ene photo-grafting of mercaptosuccinic acid or sodium 2-mercaptoethanesulfonate. The reaction is monitored by FT-IR, UV-Vis, contact angle, and gravimetry. Overall quantum yields are calculated for the two thiol-ene "click" reactions in nano-confinement, neatly revealing their chain-like nature. Top-down photolithographic patterning is demonstrated, realizing hydrophilic nanoporous "corridors" exclusively hosting water. The presented approach can be relevant for many applications where, e.g., high control and contrast in hydrophilicity, chemical functionality or refractive index are needed.
Subject(s)
Butadienes/chemistry , Elastomers/chemistry , Nanoparticles/chemistry , Polymers/chemistry , Sulfhydryl Compounds/chemistry , Hydrophobic and Hydrophilic Interactions , Photochemistry , PorosityABSTRACT
Nanoporous Solid-Liquid core waveguides were prepared by UV induced surface modification of hydrophobic nanoporous polymers. With this method, the index contrast (deltan = 0.20) is a result of selective water infiltration. The waveguide core is defined by UV light, rendering the exposed part of a nanoporous polymer block hydrophilic. A propagation loss of 0.62 dB/mm and a bend loss of 0.81 dB/90 degrees for bend radius as low as 1.75 mm was obtained in these multimode waveguides.
ABSTRACT
Surface modification of nanoporous 1,2-polybutadiene of pore diameter approximately 15 nm was accomplished by physisorption of sodium dodecyl sulfate (SDS) in water. Loading of the aqueous solution and the accompanying physisorption of SDS into the hydrophobic nanoporous films were investigated in a wide range of concentrations. The loading showed varying dependence on the SDS concentration. No loading was observed for SDS concentrations below 4.0 mM. At concentrations above 5.0 mM, the initial part of loading showed a linear dependence on the square root of time, which can be interpreted as diffusion-controlled dynamics. Both the specific equilibrium loading and the final SDS adsorption reached plateau values at concentrations above 6.8 mM. The infiltration of SDS into the nanoporous film was mainly followed by gravimetry and for a few samples confirmed by X-ray photoelectron spectroscopy (XPS). The SDS adsorption isotherm can be well described by the Langmuir model, consistent with a monolayer adsorption onto the pore walls. The surface modified by the surfactant clearly showed water wettability, in contrast to the original hydrophobic nanoporous 1,2-PB. We also looked at the release process of SDS out of the nanopores in the presence of excess of water or methanol. A discussion of the very different time scales of release in the two media is presented at the end of the paper.
ABSTRACT
Surface-initiated atom transfer radical polymerization (ATRP) and click chemistry were used to obtain functional nanoporous polymers based on nanoporous 1,2-polybutadiene (PB) with gyroid morphology. The ATRP monolith initiator was prepared by immobilizing bromoester initiators onto the pore walls through two different methodologies: (1) three-step chemical conversion of double bonds of PB into bromoisobutyrate, and (2) photochemical functionalization of PB with bromoisobutyrate groups. Azide functional groups were attached onto the pore walls before click reaction with alkynated MPEG. Following ATRP-grafting of hydrophilic polyacrylates and click of MPEG, the originally hydrophobic samples transformed into hydrophilic nanoporous materials. The successful modification was confirmed by infrared spectroscopy, contact angle measurements and measurements of spontaneous water uptake, while the morphology was investigated by small-angle X-ray scattering and transmission electron microscopy.
ABSTRACT
Protein adsorption on modified and unmodified polymer surfaces investigated through radiolabeling experiments showed a tendency for higher than expected albumin and immunoglobulin G (IgG) adsorption. Possible enhanced protein aggregation and degradation caused by the iodine labeling method used were analyzed through chromatography and spectroscopy techniques. Results show that the iodine labeling method using chloramine-T (CAT) as an oxidizing agent can cause both enhanced aggregation and fragmentation of proteins. Albumin shows an enhanced tendency to aggregate after iodine labeling using the CAT method, and higher amounts of fragmentation are observed for CAT-labeled IgG molecules relative to unlabeled IgG molecules as well as to IgG molecules labeled using the Iodo-Gen method. These results show that the widely applied method of radioisotope labeling for quantitative assessment of protein adsorption should be used with caution and preferably should be validated by a label-free methodology for each combination of radiolabel and protein. The results obtained in this study can be used to optimize investigation of protein adsorption on surfaces of materials for biomedical devices.
Subject(s)
Immunoglobulin G/chemistry , Iodine Radioisotopes , Adsorption , Biocompatible Materials , Chromatography, Gel/methods , Chromatography, High Pressure Liquid , Humans , Immunoglobulin G/blood , Immunoglobulin G/isolation & purification , Kinetics , Radioisotope Dilution Technique , Spectrometry, Mass, Matrix-Assisted Laser Desorption-IonizationABSTRACT
A new method for quantitative etching of the poly(dimethylsiloxane) block in polystyrene-poly(dimethylsiloxane) (PS-PDMS) block copolymers is reported. Reacting the block copolymer with anhydrous hydrogen fluoride renders a nanoporous material (NPM) with the remaining glassy PS maintaining the original bulk morphology. 1H NMR, mass difference, size exclusion chromatography, and X-ray photoelectron spectroscopy were used to characterize the materials before and after etching. NPMs containing spherical and gyroid cavities were prepared, as ascertained by small-angle X-ray scattering. This is the first report on block copolymer-based NPM films of millimeter thickness containing secluded spherical holes. Surface images by AFM and SEM are consistent with the SAXS findings.