Advanced removal of Reactive Yellow 84 azo dye using functionalised amorphous calcium carbonates as adsorbent.

Two environmentally friendly organics (ethylenediaminetetraacetic acid, EDTA and its easier biodegradabe isomer, ethylenediamine-N, N'-disuccinic acid, EDDS) were used to dope calcium carbonate (CC) nanoparticles intending to increase their adsorptive properties and evaluate adsorption performance (uptake capacity and removal efficiency) for the persistent Reactive Yellow 84 azo dye. Easily synthesized nanomaterials were fully characterized (morphology and size, mineralogy, organic content, surface area, pore size and hydrodynamic diameter). RY84 removal was performed using two consecutive processes: photodegradation after adsorption. The CC-EDTA particles were most efficient for dye removal as compared to the plain and CC-EDDS particles. Adsorption kinetics and isotherms were considered for the CC-EDTA system. 99% removal occurred via adsorption on 1 g/L of adsorbent at 5 mg/L dye concentration and pH of 8 and it decreased to 48% at 60 mg/L. Maximum uptake capacity as described by Langmuir is 39.53 mg/g. As post-adsorption, under UVA irradiation, in the presence of 40 mmol/L H2O2, at dye concentration of 10 mg/L the highest degradation was 49.11%. Substantial decrease of adsorption (ca. 4 times) and photodegradation (ca. 5 times) efficiencies were observed in wastewater effluent as compared to distilled water. The results have important implications to wastewater treatments and appropriate decisions making for the choice of treatment process, process optimization and scaling up to pilot and industrial levels.

Geochemical investigations of noble metal-bearing ores: Synchrotron-based micro-analyses and microcosm bioleaching studies.

Auriferous sulphide ores often incorporate micro-fine (or invisible) gold and silver particles in a manner making their extraction difficult. Nobel metals are lost in the tailings due to the refractory nature of these ores. Bioleaching is an environment-friendly alternative to the commonly used and toxic cyanidation protocols for gold extraction from refractory ores. In this paper, we investigate gold and silver bioleaching from porphyry and epithermal mineralisation systems, using iron-oxidizing bacteria Acidithiobacillus ferrooxidans. The invisible Au, sequestered in refractory ores, was characterised in situ by synchrotron micro X-Ray Fluorescence (SR-µ-XRF) and X-ray Absorption Spectroscopy (XAS), offering information on Au unaltered speciation at the atomistic level within the ore matrices and at a micro-scale spatial resolution. The SR-µ-XRF and XAS results showed that 10-20 µm sized elemental Au(0) nuggets are sequestered in pyrite, chalcopyrite, arsenopyrite matrices and at the interface of a mixture of pyrite and chalcopyrite. Moreover, the preliminary bioleaching experiments of the two types of ores, showed that Acidithiobacillus ferrooxidans can catalyse the dissolution of natural heterogeneous Fe-rich geo-matrices, sequestering Au and Ag and releasing particulate phases or partially solubilising them within 60 days. These results provide an understanding of noble metal sequestration and speciation within natural ores and a demonstration of the application of synchrotron-based micro-analysis in characterizing economic trace metals in major mineral structures. This work is a contribution to the ongoing efforts towards finding feasible and greener solutions of noble metal extraction protocols.

Iron phthalocyanine-sensitized magnetic catalysts for BPA photodegradation.

The catalytic behavior of iron phthalocyanine (FePc)-sensitized magnetic nanocatalysts was evaluated for their application in the oxidative treatment of Bisphenol A (BPA) under mild environmental conditions. Two types of FePc (Fe(II)Pc and Fe(III)Pc), which are highly photosensitive compounds, were immobilized on the surface of functionalized magnetite. The nanomaterials were characterized by high resolution transmission electron microscopy (HR-TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analyses (TGA). The generation of singlet oxygen by nanomaterials was also investigated. In the presence of UVA light exposure (365 nm) and 15 mM H2O2, the M@Fe(III)Pc photocatalyst gave the best results; for a catalyst concentration of 2.0 g L - 1, around 60% BPA was removed after 120 min of reaction. These experimental conditions were further tested under natural solar light exposure, for which also M@Fe(III)Pc exhibited enhanced oxidative catalytic activity, being able to remove 83% of BPA in solution. The water samples were less cytotoxic after treatment, this being confirmed by the MCF-7 cell viability assay.

Baltic Fucus vesiculosus as potential bio-sorbent for Zn removal: Mechanism insight.

This research aimed to find the best phenotype of the brown algae Fucus vesiculosus (kelp) which has the greater potential to become a sorption byproduct for Zn removal from contaminated waters. Thus, the Zn uptake capacity and sorption mechanisms of the kelp collected from the Baltic Sea shore was, for the first time, investigated under various conditions, and compared to the phenotype habiting on the Irish Sea shore. Sorption studies were performed investigating the effect of algal dosage, Zn sources as well as algal harvesting time of the year on Zn uptake capacity. The results suggested that the Baltic algae is a better bio-sorbent for Zn uptake. Sorption mechanisms were studied by employing various indirect and direct approaches, more importantly, including high resolution synchrotron X-Ray Fluorescence and X-Ray Absorption Spectroscopy (XAS) and molecular modelling (MM). The results revealed that alginate and cellulose are among the main polysaccharide bonding Zn at algal surface, via coordination with O atoms from carboxyl and hydroxyl groups. XAS results giving direct measurements of Zn bonding environment on algal surface are supported by MM outputs and suggested that Zn is surrounded by ca. 5 O atoms at interatomic distances varying from 1.94 to 2.02 Å. The results contribute to understanding sorption mechanisms which can further lead to finding the best eluent for Zn desorption from the used biomass, bio sorbent reconditioning and reuse in multiple sorption desorption cycles as well as process optimization before industrial scaling up.

Experimental and simulation results of the adsorption of Mo and V onto ferrihydrite.

This study aims to highlight discrepancies between experimental and simulation linked to the mechanisms of Mo and V adsorption onto ferrihydrite (FHY) nanoparticles. We have measured adsorption capacities and uptake efficiencies and then fitted and compared these with outputs from various geochemical and adsorption models that were run as a function of pH, surface area (SA) and ferrihydrite particles size distributions. Our results revealed that the experimental data for the Mo system could be fitted very well, but this was not the case for the V system, when a model default value for the SA of FHY of 600 m2 g-1 was used. The discrepancy in the results for the V system can be explained by the lack of specific V species and/or associated constants in databases and variation in software versions, which change the outputted chemical species. Our comparative results also confirm that any experimental variables used as modelling inputs need to be checked carefully prior to any modelling exercises.

Zn adsorption onto Irish Fucus vesiculosus: Biosorbent uptake capacity and atomistic mechanism insights.

This study presents a multifaceted approach of Zn adsorption onto dry Fucus vesiculosus originating from the Irish Sea. Metal chemistry as well as algae surface charge properties were characterized before adsorption. Zn adsorption tests were run as function of: pH, algae concentration and metal source. A comparison with Co, Cd, and Cu adsorption - in mono-ion solutions was also performed. Adsorption kinetics, fitted with pseudo-first order (PFO) and pseudo-second order (PSO) kinetic model, allowed the uptake parameters to be found and a comparison of kinetic rates. Synchrotron X-Ray-Florescence and X-Ray Absorption Spectroscopy measurements of Zn on algae after exposure permitted the extraction of direct information about Zn spatial distribution and bonding environment. The results showed that the carboxylic groups are the ones involved in the heterogeneously distributed Zn adsorption at low pH, Zn being coordinated with 5-6 O at bond distances varying from 1.98 to 2.03 Å - as in Zn alginate. Synchrotron results provide confirmation that, relative to Zn, alginate is one of the main algae components responsible for metal binding.

Ectonucleotidase Inhibitory and Redox Activity of Imidazole-Based Organic Salts and Ionic Liquids.

Cytotoxicity against cancer and normal cells, inhibition of ectonucleotidase, and redox properties of a new group of imidazole-based organic salts and ionic liquids were studied. The tetrachloroferrate salt of a 1-methylimidazole derivative of salicylic aldehyde had most prominent inhibitory activity against ectonucleotidase as well as a higher cytotoxicity against HeLa cells and lower cytotoxicity against BHK-21 cells than the reference compound carboplatin. The studied compounds exhibited a moderate level of antioxidant activity with better results for the salicylic aldehyde derivatives than for spiropyrans. Moreover, these compounds did not generate singlet oxygen.

Functionalized magnetic nanoparticles: Synthesis, characterization, catalytic application and assessment of toxicity.

Cost-effective water cleaning approaches using improved treatment technologies, for instance based on catalytic processes with high activity catalysts, are urgently needed. The aim of our study was to synthesize efficient Fenton-like photo-catalysts for rapid degradation of persistent organic micropollutants in aqueous medium. Iron-based nanomaterials were chemically synthesized through simple procedures by immobilization of either iron(II) oxalate (FeO) or iron(III) citrate (FeC) on magnetite (M) nanoparticles stabilized with polyethylene glycol (PEG). Various investigation techniques were performed in order to characterize the freshly prepared catalysts. By applying advanced oxidation processes, the effect of catalyst dosage, hydrogen peroxide concentration and UV-A light exposure were examined for Bisphenol A (BPA) conversion, at laboratory scale, in mild conditions. The obtained results revealed that BPA degradation was rapidly enhanced in the presence of low-concentration H2O2, as well as under UV-A light, and is highly dependent on the surface characteristics of the catalyst. Complete photo-degradation of BPA was achieved over the M/PEG/FeO catalyst in less than 15 minutes. Based on the catalytic performance, a hierarchy of the tested catalysts was established: M/PEG/FeO > M/PEG/FeC > M/PEG. The results of cytotoxicity assay using MCF-7 cells indicated that the aqueous samples after treatment are less cytotoxic.

Thin films containing oxalate-capped iron oxide nanomaterials deposited on glass substrate for fast Fenton degradation of some micropollutants.

The main goal of the study was to evaluate the catalytic activity of two hybrid nanocatalysts consisting in Fe3O4 nanoparticles modified with either chitosan (CS) or polyethylene glycol (PEG)/ferrous oxalate (FO), and further deposited on solid substrate as thin films. X-ray powder diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, and scanning electron microscopy (SEM) were employed for the structural and morphological characterizations of the heterogeneous catalysts. The degradation kinetic studies of two reactive azo dye (Reactive Black 5 (RB5) and Reactive Yellow 84 (RY84)) as well as Bisphenol A (BPA) solutions were carried out using Fenton-like oxidation, in the presence of different concentrations of H2O2, at initial near-neutral pH and room temperature. The results indicated that a low amount of catalytic material (0.15 g/L), deposited as thin film, was able to efficiently trigger dye degradation in solution in the presence of 6.5 mmol/L H2O2 for RB5 and of only 1.6 mmol/L H2O2 in the case of BPA and RY84. In the presence of complex matrices such as WWTP waters, the removal of BPA was low (only 24% for effluent samples). Our findings recommend the studied immobilized nanocatalysts as promising economical tools for the pre-treatment of wastewaters using advanced oxidation processes (AOPs).

Ozone photolysis of paracetamol in aqueous solution.

The degradation of a paracetamol (N-acetil-para-aminofenol) aqueous solution (C (0) P = 5 mmol L(-1)) is studied in a bench-scale setup by means of simple ozonation (O3) and ozonation catalyzed with UV light (O3/UV) in order to quantify the influence of UV light on the degradation process. The results have shown that under the adopted experimental conditions (25°C, applied ozone dose = 9.8 mg L(-1) and gas flow rate of 20 L h(-1)) both oxidative systems are capable of removing the substrate with mineralization degrees up to 51% for ozonation and 53% for O3/UV. HPICE chromatography allowed the detection of nitrate ions and maleic and oxalic acids as ultimate carboxylic acids. The experimental data have been interpreted through 5 indicators: the conversion of paracetamol (XP ), the conversion degree of TOC (XTOC ), the apparent rate constant (kap ), the Hatta number (Ha) and the enhancement factor (E). The main advantage of photo-ozonation compared to simple ozonation was a more advanced conversion (79% vs. 92% after 90 min). The paracetamol decay follows a pseudo-first-order reaction with a superior rate constant (higher by 54%) for the UV catalyzed system in comparison with direct ozonation. Mineralization is slightly accelerated (+4%) in the O3/UV system, due to the additional production of hydroxyl radicals induced by the UV light and a higher Hatta number (+24%). Nevertheless, the process was still in the slow reaction kinetic regime (Ha < 0.3), and the enhancement factor was not significantly increased. The results are useful for the design and scale-up of the gas-liquid processes.

Chemical, biological, and ecotoxicological assessment of pesticides and persistent organic pollutants in the Bahlui River, Romania.

BACKGROUND, AIM, AND SCOPE: Current knowledge on environmental impacts of industrial activities in Romania, particularly persistent organic pollutants (POPs), indicates that environmental standards of the European Union are not systematically met. In our study area, additional sources of POPs are agriculture and domestic wastes. Very scarce information is available upon environmental contaminations and effects. In the present study, we investigated the chemical pollution and their eventual impact on the ecosystem by measuring POPs and by using biological indicators of pollution. MATERIALS AND METHODS: The survey was carried out at six main sample sites along the Bahlui River. Sediments were chemically analysed for their content in polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs) and organochlorine pesticides (OCPs)-hexachlorocyclohexanes (HCHs) isomers and the dichlorodiphenyl trichloroethane (DDT) family. River water was biologically monitored at the level of phytoplankton and benthic invertebrates' communities. Water samples from six locations have been analyzed for algal species composition and correspondence to various water quality indices. Biological samples have been taken from the same locations so as to calculate the macroinvertebrate indices. In the most polluted areas, as revealed by previous methods, toxicity was tested by exposing the green alga Pseudokirchneriella subcapitata and the cladoceran Daphnia magna to various dilutions of water sample. RESULTS: Important concentrations of POPs were identified only in sediments at river mouths (sites S5 and S6). Along the year, the sum of PCB concentrations ranged between 3 and 10 ng/g dw (S5), and between 4 and 26 ng/g dw (S6). Concentration of HCHs ranged between 0.4 and 3 ng/g dw (both S5 and S6) with a higher contribution of the gamma-HCH (30-70%), followed by beta-HCH (20-50%). The beta-HCH isomer was found at lower concentrations or even not detected in outer city sites. DDTs were found at higher concentrations than HCHs and ranged between 0.18 and 4 ng/g dw (S5) and between 0.56 and 18 ng/g dw (S6). The parent compound, p,p'-DDT, could be detected only in low concentrations (up to 5 ng/g dw) and contributed with less than 30% to the sum of DDTs in sediment. The principal contributors of the SigmaDDTs in sediment were p,p'-DDE, and p,p'-DDD. The o,p'-DDD and DDT isomers were minor contributors to the sum of DDT. PAHs were found at higher concentrations than DDTs and ranged between 6 and 36 ng/g dw (S5) and between 36 and 155 ng/g dw (S6). Fluoranthene was predominant (up to 40%), followed by phenantrene (up to 30%), naphthalene (up to 35%), and benzo-(g,h,i)-perylene (up to 23%). The saprobity index and the diatom index increased from springs to river mouth, indicating a decrease in the water quality, but within the limits of moderate pollution. The saprobity index varied between 1.99 at spring to 2.70 at mouth. The diatom index varied from 3.48 to 3.14. The species' richness in phytoplankton has a less clear pattern along the river, but in general, it appears to be negatively influenced by pollution. At the level of biological consumer species, the analyses of the macroinvertebrates confirm the situation and the tendency shown with algae. In addition, the Shannon-Wiener index, the Pielou evenness index, and the McNaughton dominance index indicate a peculiar pattern: invertebrate communities appear to a have a more stable structure along the river, with visible shifts at springs and at river mouths. Water toxicity testing indicates low toxicity of river waters around the city of Iasi, with two notable exceptions: the point pollution at the domestic wastewater treatment discharge and at the old open-air deposit of domestic solid wastes. Another important result was that tested algae appeared to be more readily affected than tested cladoceran: EC(50) (percent effluent) was 16 in algae and 28 in cladocerans. The slope of toxic effect was also much steeper in cladocerans (6) than in algae (1.8), which means that the toxic effect is more sudden on the tested invertebrates than on the tested algae. DISCUSSION: Pollutant concentrations reported herein are lower or similar than those reported for the sediments by earlier studies (RIZA 2000; Dragan et al., Int J Environ Anal Chem 86:833-842, 2006). Ratios of individual PAH compounds indicate important pyrolytic inputs and suggest that PAHs in the area are derived from the combustion of fossil fuels. Biologically, the waters appear to be beta-mesosaprobic towards alpha-mesosaprobic according to the saprobic index classification and undergo moderate pollution according to the diatom index classification. Water quality decreases from springs to river mouths. Algal species richness index has a less clear pattern along the river. Water toxicity is low, but certain sources of point pollution require increased attention. CONCLUSIONS: The water quality is better than expected, probably because of the drop in pollution intensity following the collapse of local agricultural and industrial activity following the fall of communism in 1989. Nevertheless, further studies will be needed to confirm and refine our results. While this study draws no strident alarm, it appeals for high attention, particularly because the economic activity in the area is expected to increase. RECOMMENDATIONS AND PERSPECTIVES: Future close monitoring will be necessary for insuring compliance with the Water Framework Directive, and for refining standards and understanding of the local situation, but with relevance for the wider international community. On the basis of the situation described in the present study, we recommend that future studies dedicate specific efforts to point pollution and effluent toxicity, particularly around the city of Iasi. For a better understanding of pollution and its effects, we recommend pursuing the type of multidisciplinary investigations proposed by the present study: chemical, ecotoxicological, and ecological. We also recommend that new methods should be developed and/or refined, like the empirical determination of partitioning coefficients in water and soils, process-based toxicity methods in ecotoxicological assessments, searching for interactions between pollution, producers, and consumers in aquatic ecosystems. We also recommend preference for cheaper survey methods, as these will be more applicable locally.

Simulated solar UV-irradiation of endocrine disrupting chemical octylphenol.

The photolysis of octylphenol (OP) was investigated using a solar simulator in the absence/presence of dissolved natural organic matter (DNOM), HCO(3)(-), NO(3)(-) and Fe(III) ions. The effects of different parameters such as initial pH, initial concentration of substrate, temperature, and the effect of hydrogen peroxide concentration on photodegradation of octylphenol in aqueous solution have been assessed. The results indicate that the oxidation rate increases in the presence of H(2)O(2), nitrate and DNOM. Phenol, 1,4-dihydroxylbenzene and 1,4-benzoquinone were identified as intermediate products of photodegradation of octylphenol, through an HPLC method. In addition, the disappearance of the estrogenic activity of octylphenol during irradiation using YES test was investigated. Based upon the YES test results, there was a strong decrease of estrogenic activity of octylphenol after 8h irradiation in the presence of hydrogen peroxide.

The effect of nitrate, Fe(III) and bicarbonate on the degradation of bisphenol A by simulated solar UV-irradiation.

The photoinitiated degradation of bisphenol A (BPA, 520 micromol/L) was investigated using a solar simulator in the absence/presence of NO(3)(-), Fe(III), and HCO(3)(-). The concentrations of NO(3)(-), Fe(III), and HCO(3)(-) were 0-160, 0-10, and 0-820 micromol/L, respectively, and were chosen to simulate a natural aquatic environment. The experimental region was explored using a Box-Behnken design for three factors, extended to experimentally include all eight possible combinations of presence/absence of the factors studied. The results show that, after 7h of irradiation, photolysis occurs only to a minimal degree (2%) in the absence of NO(3)(-) and HCO(3)(-). Increasing the concentration of NO(3)(-) and HCO(3)(-) gives rise to up to 24% degradation after 7h of irradiation. The concentration of Fe(III) was found to play no active role under the conditions studied. A simple linear model is given that very well describes the results obtained.

Degradation of endocrine disrupting bisphenol A by 254 nm irradiation in different water matrices and effect on yeast cells.

The photodegradation of bisphenol A (BPA) in pure water, surface water and wastewater effluents was studied. The effect of different hydrogen peroxide concentrations on degradation was investigated. The rate of BPA photolysis in the presence of hydrogen peroxide was lower in wastewater effluent than in purified water. Phenol, 1,4-dihydroxylbenzene and 1,4-benzoquinone were identified by means of HPLC as intermediate products of the photodegradation of bisphenol A. In addition, the disappearance of the estrogenic activity of bisphenol A during irradiation was shown by the YES test. Based upon the YES test results, there was a strong decrease of estrogenic activity of parent compound after 120 min irradiation in the presence of hydrogen peroxide.

Photodegradation of endocrine disrupting chemical nonylphenol by simulated solar UV-irradiation.

The photolysis of nonylphenol (NP) was investigated using a solar simulator in the absence/presence of dissolved organic matter (DOM), HCO3-, NO3- and Fe(III) ions. The effects of different parameters such as initial pH, initial concentration of substrate, temperature, and the effect of hydrogen peroxide concentration on photodegradation of nonylphenol in aqueous solution have been assessed. The results indicate that the oxidation rate increases in the presence of H2O2, Fe(III) and DOM with dissolved organic carbon concentrations not higher than 3 mg L(-1). Phenol, 1,4-dihydroxylbenzene and 1,4-benzoquinone were identified as intermediate products of photodegradation of nonylphenol, through an HPLC method. In addition, the disappearance of the estrogenic activity of nonylphenol during irradiation using YES test was investigated. Based upon the YES test results, there was a strong decrease of estrogenic activity of nonylphenol after 80 h irradiation in the presence of hydrogen peroxide.