Carbon black and chitin nanofibers for green tyres: Preparation and property evaluation.

This research highlights the synergistic use of carbon black (CB) and chitin nanofibers (CHNFs) for developing green tyres for the first time. The CHNFs (12-30 nm) were prepared from chitin powder with the help of steam explosion and mild oxalic acid hydrolysis. The CHNFs were uniformly dispersed in natural rubber (NR) latex, dried, and mixed with CB in a two-roll mill to form NR/CB/CHNF composites. The NR/CB/CHNF composite at 1 phr CHNF loading exhibited tensile and tear strengths that were about 47 and 160 % greater than the NR-Neat, respectively. The dynamic mechanical analysis showed that the loss tangent (tan δ) at 60 °C was 50 % lower for the NR/CB/CHNF 1.0 composite than for the NR/CB50 composite. The study succeeded in developing a new green tyre tread formulation that would be helpful for attaining sustainability and a circular economy.

Effect of oxalic acid and sulphuric acid hydrolysis on the preparation and properties of pineapple pomace derived cellulose nanofibers and nanopapers.

Nanocellulose is the "green magnet" which attracts a wide spectrum of industries towards it due to its availability, biodegradability, and possible smart applications. For the first time, pineapple pomace was being explored as an economic precursor for cellulose nanofibers. Nanofiber isolation was accomplished using a chemo-mechanical method and solution casting was adopted for the development of nanopapers. Moreover, the study examines the structural, optical, crystalline, dimensional, and thermal features of nanofibers isolated using different acid hydrolysis (oxalic acid and sulphuric acid) methods. Fourier-transform infra-red spectroscopy, 13C solid-state nuclear magnetic resonance spectroscopy, and X-ray diffraction analysis indicated the presence of type I cellulose. The transmittance, crystallinity index, and thermal stability of PPNFS (sulphuric acid treated fiber) were greater than PPNFO (oxalic acid treated fiber). The transmission electron microscopy and dynamic light scattering analysis confirmed the nanodimension of PPNFO and PPNFS. While comparing the optical and mechanical properties of nanopapers, PPNFS outperforms PPNFO. The tensile strength of the prepared nanopapers (64 MPa (PPNFO) and 68 MPa (PPNFS)) was found to be high compared to similar works reported in the literature. The prepared nanopaper is proposed to be used for food packaging applications.

Chlorine-free extraction and structural characterization of cellulose nanofibers from waste husk of millet (Pennisetum glaucum).

This study aims to extract cellulose nanofibers (CNFs) from a sustainable source, i.e. millet husk, which is an agro-waste worthy of consideration. Pre-treatments such as mercerisation, steam explosion, and peroxide bleaching (chlorine-free) were applied for the removal of non-cellulosic components. The bleached millet husk pulp was subjected to acid hydrolysis (5% oxalic acid) followed by homogenization to extract CNFs. The extracted CNFs were characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Dynamic Light Scattering (DLS), Energy Dispersive X-ray Spectroscopy (EDX), Thermogravimetry (TG and DTG), Differential scanning calorimetry (DSC), and Solid state 13C nuclear magnetic resonance spectroscopy (solid state 13C NMR). The isolated CNFs show a typical cellulose type-I structure with a diameter of 10-12 nm and a crystallinity index of 58.5%. The appearance of the specific peak at 89.31 ppm in the solid state 13C NMR spectra validates the existence of the type-I cellulose phase in the prepared CNFs. The prepared CNFs had a maximum degradation temperature (Tmax) of 341 °C, that was 31 °C greater than raw millet husk (RMH). The outcome of the study implies that the nanofibers are prominent alternatives for synthetic fibers for assorted potential applications, especially in manufacturing green composites.