Influence of water-film-forming-unit on the enhanced removal of carbon dioxide from mixed gas using water absorption apparatus.

This research uses tap water to absorb carbon dioxide from mixed gas (N2 and CO2) in an absorption apparatus coupled with a water-film-forming-unit (WFFU). The objective is to assess the benefits of using a WFFU to enhance CO2 removal efficiency at low pressure conditions. Based on our results, the WFFU significantly improves CO2 capture at 0.30 MPa in a water absorption system with two WFFUs. The CO2 removal efficiency was 20% greater than for systems without WFFUs. Moreover, statistical data attained by the Taguchi analysis method showed that the number of WFFUs used in the absorption system has the greatest influence on CO2 removal efficiency (contribution percentage = 50.65%) compared to gas pressure, initial CO2 concentration, gas-to-liquid ratio, and liquid temperature. We also thoroughly investigated the effects of these factors on CO2 removal performance. The optimum conditions for CO2 removal efficiency in a system equipped with two WFFUs are low temperature, low gas-to-liquid ratio, low gas pressure (0.25-0.30 MPa), and high inlet CO2 concentration. These findings could provide an effective method for capturing CO2 from exhaust gases, and thus help mitigate global warming.

Response surface method for modeling the removal of carbon dioxide from a simulated gas using water absorption enhanced with a liquid-film-forming device.

This paper presents the results from using a physical absorption process to absorb gaseous CO2 mixed with N2 using water by producing tiny bubbles via a liquid-film-forming device (LFFD) that improves the solubility of CO2 in water. The influence of various parameters-pressure, initial CO2 concentration, gas-to-liquid ratios, and temperature-on the CO2 removal efficiency and its absorption rate in water were investigated and estimated thoroughly by statistical polynomial models obtained by the utilization of the response surface method (RSM) with a central composite design (CCD). Based on the analysis, a high efficiency of CO2 capture can be reached in conditions such as low pressure, high CO2 concentration at the inlet, low gas/liquid ratio, and low temperature. For instance, the highest removal efficiency in the RSM-CCD experimental matrix of nearly 80% occurred for run number 20, which was conducted at 0.30MPa, CO2 concentration of 35%, gas/liquid ratio of 0.71, and temperature of 15°C. Furthermore, the coefficients of determination, R2, were 0.996 for the removal rate and 0.982 for the absorption rate, implying that the predicted values computed by the constructed models correlate strongly and fit well with the experimental values. The results obtained provide essential information for implementing this method properly and effectively and contribute a promising approach to the problem of CO2 capture in air pollution treatment.

Synergistic effect of pressurized carbon dioxide and sodium hypochlorite on the inactivation of Enterococcus sp. in seawater.

This study investigated the effect of combined treatments using pressurized carbon dioxide (PCD) and sodium hypochlorite (NaOCl) on the inactivation of Enterococcus sp. in artificial seawater. Bacterial inactivation was conducted in a liquid-film-forming apparatus with various pressure conditions, CO2 supply rates, and chlorine dosages. Combined PCD/chlorine treatments resulted in greater disinfection efficiency than those for the two individual treatments. Synergy values were correlated with pressure and CO2 concentrations (p < 0.001). Combination of 0.9 MPa PCD (various CO2 supply rates: 25% CO2 + 75% N2, 50% CO2 + 50% N2, and 100% CO2) and chlorine (0.20 mg L-1) yielded average synergy values of 4.9, 5.2, and 4.4 log, respectively, within 3 min. Combined treatment with PCD (100% CO2, 0.3 MPa, and 20 °C) and chlorine (0.20-0.22 mg L-1) achieved an average synergy value of 4.6 log and complete inactivation (5.2-5.5 log reductions) of Enterococcus sp. within 4 min. In contrast, when the two individual treatments (PCD and chlorine) were used, only 3.7 and 1.8-2.3 log reductions, respectively, were achieved after 25 min. These findings suggest that the combined PCD/chlorine treatment has synergistic benefits and provides a promising method for the disinfection of ballast water.