ABSTRACT
This work focuses on a carbon-based imprinted polymer composite, employed as a molecular recognition and sensing interface in fabricating a disposable electrochemical sensor. The carbon-paste electrode was made of a molecularly imprinted polymer comprising a copolymer of methacrylic acid as the functional monomer and blended crosslinking monomers of N,N'-methylenebisacrylamide, and ethylene glycol dimethacrylate, with theophylline as the template. The analytical properties of the proposed theophylline sensor were investigated, and the findings revealed an increase in differential pulse voltammetric current compared to the non-imprinted electrode. Under optimized conditions, the sensor has shown high sensitivity, high selectivity, lower detection limit (2.5 µg/mL), and satisfactory long-term stability. Further, the sensor was tested in whole bovine blood and validated without any matrix effect and cross-reactivity. Additionally, chronoamperometry of the sensor chip supported a rapid determination of THO with a short response time of 3 s. This carbon-paste electrode is highly specific for theophylline and may be applied as a drug sensor for clinical use.
Subject(s)
Graphite , Molecular Imprinting , Animals , Carbon/chemistry , Cattle , Electrochemical Techniques , Electrodes , Graphite/chemistry , Limit of Detection , Polymers/chemistry , TheophyllineABSTRACT
We investigate the direct writing properties of copper (Cu) patterns on glass and polydimethylsiloxane (PDMS) substrates using femtosecond laser pulse-induced thermochemical reduction of glyoxylic acid copper (GACu) complex. The films of the GACu complex coated on the substrates were irradiated by focused femtosecond laser pulses using a low numerical aperture of 0.45. Under the same conditions, such as laser scanning speed and pulse energy, the width of the line patterns fabricated on PDMS substrates was larger than that on glass substrates. X-ray diffraction peaks of the patterns on glass substrates corresponded to Cu without significant oxidation. By contrast, although Cu patterns were fabricated on PDMS substrates at a scanning speed of 10 mm/s and pulse energy of 0.49 nJ, Cu2O was also generated under overheating conditions at a scanning speed of 1 mm/s and pulse energy of 0.37 nJ. All the patterns exhibited electrical conductivity. The minimum resistivity of the patterns on PDMS substrates is 1.4 × 10-5 Ωm, which is 10 times higher than that on glass substrates, indicating that microcracks formed by thermal shrinkage of the substrates during the laser irradiation increase the resistivity. This direct Cu writing technique on soft materials is useful for fabricating flexible microdevices.
ABSTRACT
We have fabricated Cu-based micropatterns in an ambient environment using femtosecond laser direct writing to reduce a glyoxylic acid Cu complex spin-coated onto a glass substrate. To do this, we scanned a train of focused femtosecond laser pulses over the complex film in air, following which the non-irradiated complex was removed by rinsing the substrates with ethanol. A minimum line width of 6.1 µm was obtained at a laser-pulse energy of 0.156 nJ and scanning speeds of 500 and 1000 µm/s. This line width is significantly smaller than that obtained in previous work using a CO2 laser. In addition, the lines are electrically conducting. However, the minimum resistivity of the line pattern was 2.43 × 10-6 Ω·m, which is ~10 times greater than that of the pattern formed using the CO2 laser. An X-ray diffraction analysis suggests that the balance between reduction and re-oxidation of the glyoxylic acid Cu complex determines the nature of the highly reduced Cu patterns in the ambient air.
ABSTRACT
Effect of ultrasound sonication was examined on the electroplating of iridium in aqueous hexabromoiridate(III) solution. The electrodeposits were evaluated by observing the defects of the iridium deposits by means of voltammetry, in which the current-potential curves of the iridium deposits on copper were measured. Applying ultrasound sonication to the electroplating of iridium decreased the defects including the cracks in the deposit whenever the glycerol as the additives was contained or not in the electrolyte.
