Pilot-scale process for magnetic bead purification of antibodies directly from non-clarified CHO cell culture.

High capacity magnetic protein A agarose beads, LOABeads PrtA, were used in the development of a new process for affinity purification of monoclonal antibodies (mAbs) from non-clarified CHO cell broth using a pilot-scale magnetic separator. The LOABeads had a maximum binding capacity of 65 mg/mL and an adsorption capacity of 25-42 mg IgG/mL bead in suspension for an IgG concentration of 1 to 8 g/L. Pilot-scale separation was initially tested in a mAb capture step from 26 L clarified harvest. Small-scale experiments showed that similar mAb adsorptions were obtained in cell broth containing 40 × 106 cells/mL as in clarified supernatant. Two pilot-scale purification runs were then performed on non-clarified cell broth from fed-batch runs of 16 L, where a rapid mAb adsorption ≥96.6% was observed after 1 h. This process using 1 L of magnetic beads had an overall mAb yield of 86% and 16 times concentration factor. After this single protein A capture step, the mAb purity was similar to the one obtained by column chromatography, while the host cell protein content was very low, <10 ppm. Our results showed that this magnetic bead mAb purification process, using a dedicated pilot-scale separation device, was a highly efficient single step, which directly connected the culture to the downstream process without cell clarification. Purification of mAb directly from non-clarified cell broth without cell separation can provide significant savings in terms of resources, operation time, and equipment, compared to legacy procedure of cell separation followed by column chromatography step. © 2019 American Institute of Chemical Engineers Biotechnol. Prog., 35: e2775, 2019.

Magnetophoretic Transport Line System for Rapid On-Chip Attomole Protein Detection.

A lab-on-a-chip traveling wave magnetophoresis approach for sensitive and rapid protein detection is reported. In this method, a chip-based magnetic microarray comprising lines of micrometer-sized thin film magnetic elements was used to control the movement of magnetic beads (MBs). The MBs and the chip were functionalized, forming a sandwich-type assay. The MBs were transported across a detection area, and the presence of target molecules resulted in the immobilization of MBs within this area. Target quantification was accomplished by MB counting in the detection area using an optical microscope. In order to demonstrate the versatility of the microarray, biotinylated antiavidin was selected as the target protein. In this case, avidin-functionalized MBs and an avidin-functionalized detection area were used. With a total assay time of 1 to 1.5 h (depending on the labeling approach used), a limit of detection in the attomole range was achieved. Compared to on-chip surface plasmon resonance biodetection systems, our method has a larger dynamic range and is about a factor of 500 times more sensitive. Furthermore, our MB transportation system can operate in any chip-based biosensor platform, thereby significantly improving traditional biosensors.

Influence of bio-coatings on the recording performance of neural electrodes.

Neural probes are complex devices consisting of metallic (often Pt based) electrodes, spread over an insolating/dielectric backbone. Their functionality is often limited in time because of the formation of scaring tissues around the implantation tracks. Functionalization of the probes surface can be used to limit the glial scar reaction. This is however challenging, as this treatment has to be equally efficient on all probe surfaces (metallic as well as dielectric) and should not influence the electrodes performances. This paper presents a novel technique to functionalize recording neural probes with hyaluronic acid (HyA), a major component of the extracellular matrix (ECM). HyA and the probe surface are both modified to make the reaction feasible: HyA is chemically functionalized with SS-pyridine groups while the probe surfaces are silanized. The thiol groups thus introduced on the probe surface can then react with the HyA SS-pyridine group, resulting in a covalent bonding of the latter on the former. The electrodes are protected by introducing a pretreatment step, namely an additional hyaluronic acid layer on the platinum electrode, prior to the silanization process, which was found to be effective in reducing electrode impedance under optimized conditions.

Electrochemical synthesis of gold and protein gradients on particle surfaces.

A straightforward, versatile approach to the production of protein gradients on planar and spherical particle surfaces is described. The method is based on the spatially controlled oxidation of thiolated surfaces by Au(III) ions generated via the electrochemical oxidation of a gold electrode in a phosphate-buffered saline solution (10 mM PBS, pH 7.2, 150 mM NaCl). Because the gold electrode is in direct contact with the thiolated surfaces, the released Au(III) ions, which are present as Au(III) chloride complexes, give rise to the formation of a surface gradient of Au(I)-thiolate complexes depending on the local redox potential given by the local Au(III) concentration. As is shown on the basis of the use of X-ray photoelectron spectroscopy and fluorescently labeled proteins, the Au(I)-thiolate complexes can subsequently be functionalized with thiolated proteins, yielding surface density protein gradients on micrometer-sized nonconducting polymer beads as well as linear Au(I)-thiolate gradients on planar silicon surfaces.

Small Pd nanoparticles supported in large pores of mesocellular foam: an excellent catalyst for racemization of amines.

Highly dispersed palladium nanoparticles (1-2 nm) supported in large-pore mesocellular foam (MCF; 29 nm) were synthesized. The Pd-nanocatalyst/MCF system was characterized by transmission electron microscopy (TEM), powder X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The performance of the Pd nanocatalyst obtained was examined for amine racemization. The Pd nanocatalyst showed higher activity and selectivity toward racemization of (S)-1-phenylethyl amine than any other amine racemization catalyst reported so far and it could be reused several times. Our data from TEM and XRD suggest a restructuring of the Pd nanocatalyst from amorphous to crystalline and an increase in Pd nanocatalyst size during the racemization reaction. This led to an unexpected increase of activity after the first use. The Pd nanocatalyst obtained can be integrated with other resolving processes of racemic organic compounds to increase the yield of chiral organic products.

Performance of a biomimetic oxidation catalyst immobilized on silicon wafers: comparison with its gold congener.

With the aim of extending the usefulness of an existing biomimetic catalytic system, cobalt porphyrin catalytic units with thiol linkers were heterogenized via chemical grafting to silicon wafers and utilized for the catalytic oxidation of hydroquinone to p-benzoquinone. Atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) were used to analyze the morphology and composition of the heterogeneous catalyst. The results of the catalytic oxidation of hydroquinone obtained with porphyrins grafted on silicon were compared with those obtained earlier with the same catalyst in homogeneous phase and immobilized on gold. It was found that the catalysis could run over 400 h, without showing any sign of deactivation. The measured catalytic activity is at least 10 times higher than that measured under homogeneous conditions, but also 10 times lower than that observed with the catalytic unit immobilized on gold. The reasons of this discrepancy are discussed in term of substrate influence and overlayer organization. The silicon-immobilized catalyst has potential as an advanced functional material with applications in oxidative heterogeneous catalysis of organic reactions, as it combines long-term relatively high activity with low cost.

Short and long term biocompatibility of NeuroProbes silicon probes.

Brain implants provide exceptional tools to understand and restore cerebral functions. The utility of these devices depends crucially on their biocompatibility and long term viability. We addressed these points by implanting non-functional, NeuroProbes silicon probes, without or with hyaluronic acid (Hya), dextran (Dex), dexamethasone (DexM), Hya+DexM coating, into rat neocortex. Light and transmission electron microscopy were used to investigate neuronal survival and glial response. The surface of explanted probes was examined in the scanning electron microscope. We show that blood vessel disruption during implantation could induce considerable tissue damage. If, however, probes could be inserted without major bleeding, light microscopical evidence of damage to surrounding neocortical tissue was much reduced. At distances less than 100 microm from the probe track a considerable neuron loss ( approximately 40%) occurred at short survival times, while the neuronal numbers recovered close to control levels at longer survival. Slight gliosis was observed at both short and long term survivals. Electron microscopy showed neuronal cell bodies and synapses close (<10 microm) to the probe track when bleeding could be avoided. The explanted probes were usually partly covered by tissue residue containing cells with different morphology. Our data suggest that NeuroProbes silicon probes are highly biocompatible. If major blood vessel disruption can be avoided, the low neuronal cell loss and gliosis should provide good recording and stimulating results with future functional probes. We found that different bioactive molecule coatings had small differential effects on neural cell numbers and gliosis, with optimal results achieved using the DexM coated probes.

A magnetic microchip for controlled transport of attomole levels of proteins.

A novel method of controlled transport of proteins immobilized on micrometre-sized magnetic beads in a lab-on-a-chip environment is presented. Bead motion is controlled by lithographically made magnetic elements forming transportation lines in combination with an applied in-plane rotating magnetic field. In this way, transport of attomole amounts of proteins is controlled with micrometre precision. Also, the activity of proteins immobilized on the beads is demonstrated by injecting antibodies into the system. A critical step in developing the method was to reduce sticking forces between beads and substrate during transportation of proteins. Charge interaction was found to be of minor importance compared to hydrophobic forces. To achieve a reliable transport of biologically active proteins, both substrate and beads were coated with polyethylene glycol (PEG) and the protein covered beads were suspended in buffer with surfactants. The described system fulfils all the important unit operations of a microfluidic platform and, as a further advantage, presents less need for microchannels and electric wiring.

Micropatterned surfaces: techniques and applications in cell biology.

IMPORTANCE OF THE FIELD: Engineering of cell culture substrates provides a unique opportunity for precise control of the cellular microenvironment with both spatial as well as temporal resolutions. This greatly enhances studies of cell-cell, cell-matrix and cell-factor interaction studies in vitro. AREAS COVERED IN THIS REVIEW: The technologies used for micropatterning in the biological field over the last decade and new applications in the last few years for dynamic control of surfaces, tissue engineering, drug discovery, cell-cell interactions and stem cell studies are presented. WHAT THE READER WILL GAIN: The reader will gain knowledge on the state of the art in micropatterning and its wide ranging applications in cell patterning, with new pathways to control the cell environment. TAKE HOME MESSAGE: Micropatterning of cells has been studied and developed enough to be widely applied ranging from single cell assays to tissue engineering. Techniques have evolved from many-step processes to direct writing of biologically selective patterns.

A strategic crossflow filtration methodology for the initial purification of promegapoietin from inclusion bodies.

A novel crossflow filtration methodology is demonstrated for the initial purification of the therapeutic protein, promegapoietin-1a (PMP), produced as inclusion bodies (IBs) in a recombinant Escherichia coli bioprocess. Two strategic separation steps were performed by utilizing a filtration unit with a 1000 kDa polyethersulphone membrane. The first step, aiming for separation of soluble contaminants, resulted in a 50% reduction of the host cell proteins, quantified by total amino acid analysis and a 70% reduction of all DNA, quantified by fluorometry, when washing the particulate material with a 10mM EDTA in 50mM phosphate buffer, pH 8. The second step, aiming for separation of particulate contaminants from solubilized IBs, resulted in a 97-99.5% reduction of endotoxin, used as a marker for cell debris, and was quantified by the kinetic turbidimetric LAL endotoxin assay. The overall PMP yield was 58% and 33% respectively for the two solubilizations investigated, guanidine hydrochloride and arginine, as measured by RP-HPLC. The scope was also to investigate the physical characteristics of the intermediate product/s with regard to the choice of IB solvent. Preliminary results from circular dichroism spectroscopy measurements indicate that the protein secondary structure was restored when arginine was used in the second step.

Optimizing the surface plasmon resonance/mass spectrometry interface for functional proteomics applications: how to avoid and utilize nonspecific adsorption.

A great challenge in functional or interaction proteomics is to map protein networks and establish a functional relationship between expressed proteins and their effects on cellular processes. These cellular processes can be studied by characterizing binding partners to a "bait" protein against a complex background of other molecules present in cells, tissues, or biological fluids. This so-called ligand fishing process can be performed by combining surface plasmon resonance biosensors with MS. This combination generates a unique and automated method to quantify and characterize biomolecular interactions, and identify the interaction partners. A general problem in chip-based affinity separation systems is the large surface-to-volume ratio of the fluidic system. Extreme care, therefore, is required to avoid nonspecific adsorption, resulting in losses of the target protein and carry-over during the affinity purification process, which may lead to unwanted signals in the final MS analysis and a reduction in sensitivity. In this study, carry-over of protein and low-molecular weight substances has been investigated systematically and cleaning strategies are presented. Furthermore, it is demonstrated that by the introduction of colloidal particles as a capturing and transporting agent, the recovery yield of the affinity-purified ligand could be improved nearly twofold.

Structure, stability, and orientation of BSA adsorbed to silica.

In this investigation, the structure, stability, and orientation of bovine serum albumin (BSA) adsorbed onto silica particles were studied using differential scanning calorimetry (DSC) and limited proteolysis in combination with mass spectrometry (MS). DSC gave information on the overall structural stability of BSA while limited proteolysis was used to probe the accessibility of enzymatic cleavage sites, thereby yielding information on the orientation and structure of BSA adsorbed to silica surfaces. Thermal investigation of BSA in various buffers, both free in solution and in the adsorbed state, showed that solutes that surround the protein played an important role with respect to the overall structural stability and the structural heterogeneity of BSA. Limited proteolysis with trypsin and chymotrypsin indicated that BSA in the adsorbed state is oriented with domain 2 facing the silica surface. Also, upon adsorption, no additional cleavage sites were exposed. The combination of the results presented in this study implied that BSA molecules adsorbed onto silica particles were significantly reduced in their structural stability, but not to an extent that internal residues within the native structure became fully exposed to the solution.

Recent advances in microcontact printing.

Microcontact printing is a remarkable surface patterning technique. Developed about 10 years ago, it has triggered enormous interest from the surface science community, as well as from engineers and biologists. The last five years have been rich in improvements to the microcontact printing process itself, as well as in new technical innovations, many designed to suit new applications. In this review, we describe the evolution of microcontact printing over the past five years. The review is categorized into three main sections: the improvements made to the technique, new variations, and new applications.

Thermodynamic analysis of lysozyme adsorbed to silica.

The structural stability of hen egg white lysozyme in solution and adsorbed to small colloidal silica particles at various surface concentrations was investigated using hydrogen-deuterium (H/D) exchange in combination with mass spectrometry (HDX-MS) and differential scanning calorimetry (DSC). The combination of HDX-MS and DSC allows a full thermodynamic analysis of the lysozyme structure as both the enthalpy and the Gibbs free energy can be derived from the various measurements. Moreover, both HDX-MS and DSC provide information on the relative structural heterogeneity of lysozyme in the adsorbed state compared to that in solution. Results demonstrated that at high surface coverage, the structural stability of lysozyme was only marginally affected by adsorption to silica particles whereas the unfolding enthalpy decreased by more than 10%, meaning that the entropy of lysozyme increased with a similar value upon adsorption. Furthermore, the structural heterogeneity increased considerably. At lower surface concentrations, the structural heterogeneity increased further whereas the enthalpy of unfolding decreased. Further analyses of the HDX-MS experiments clearly indicated that folding/unfolding of lysozyme occurs through a two-domain process. These two domains had a similar amount of structural elements and a difference in stabilization energy of 8 kJ/mol, regardless if lysozyme was in solution or adsorbed to silica.

Localized changes in the structural stability of myoglobin upon adsorption onto silica particles, as studied with hydrogen/deuterium exchange mass spectrometry.

A new method is presented for monitoring the conformational stability of various parts of a protein that is physically adsorbed onto nanometer-sized silica particles. The method employs hydrogen/deuterium (H/D) exchange of amide hydrogens, a process that is extremely sensitive to structural features of proteins. The resulting mass increase is analyzed with Fourier transform ion cyclotron resonance (FTICR) mass spectrometry. Higher structural specificity is obtained by enzymatically cleaving the adsorbed proteins prior to mass spectrometric analysis. The mass increases of four peptic fragments of myoglobin are followed as a function of the H/D exchange time. The four peptic fragments cover 90% of the myoglobin structure. Two of the peptic fragments, located in the middle of the myoglobin sequence and close to the heme group, do not show any adsorption-induced changes in their structural stability, whereas the more stable C- and N-terminal fragments are destabilized. Interestingly, for the N-terminal fragment, comprising residues 1-29, two distinct and equally large conformational populations are observed. One of these populations has a stability similar to that in solution (-23 kJ/mol), whereas the other population is highly destabilized upon adsorption (-11 kJ/mol).

Surface-dependent conformations of human plasma fibronectin adsorbed to silica, mica, and hydrophobic surfaces, studied with use of Atomic Force Microscopy.

Human plasma fibronectin (Fn) is a large flexible protein stabilized by intermolecular ionic interactions forming a compact structure. On altering solution conditions, the structure can revert to a more expanded state, thereby exposing previously hidden domains (e.g., cell-binding sites). Electron microscopy images of Fn air-sprayed onto mica surfaces show elongated protein structures, indicating a surface-induced structural change. This makes it interesting to investigate the influence of surface properties on the structure of adsorbed Fn. We have used intermittent-contact Atomic Force Microscopy to investigate the structure of Fn adsorbed onto mica, silica, and methylated silica surfaces. We observed that on silica surfaces, which is hydrophilic, most (70%) of the molecules had an elongated structure with partial intramolecular chain interactions, compare to molecules adsorbed on hydrophobic, methylated surfaces, where a compact structure predominated (70%). On mica surfaces, both compact and elongated protein structures were observed, with a slight preference for the elongated form (53%). Results show that surface physical properties influence the molecular structure of fibronectin on adsorption, which could provide useful information in understanding surface-induced in vivo responses.

Surface functionalization of silicon oxide at room temperature and atmospheric pressure.

A novel method to derivatize silicon surfaces with 3-mercaptopropylsilane molecules has been developed and optimized. This method is based on an argon flow that increases the evaporation rate of the silane molecules by lowering the partial pressure of the silane molecules in gas phase above the liquid silane, at room temperature. X-ray photoelectron spectroscopy studies of the surfaces showed a dense monolayer coverage as well as hydrolysis of the silane methoxy groups. Atomic force microscopy was used to investigate the roughness of the surfaces after each step of the derivatization process. Since the final surface has a measured surface roughness of 0.19 nm, this method will be especially useful for further synthetic routes and advanced single molecule detection studies of interactions on surfaces as well as improvement of existing conventional techniques for surface derivatization and analysis.

Thermodynamic Analysis of Proteins Adsorbed on Silica Particles: Electrostatic Effects.

Electrostatic effects on protein adsorption were investigated using differential scanning calorimetry (DSC) and adsorption isotherms. The thermal denaturation of lysozyme, ribonuclease A (RNase), and alpha-lactalbumin in solution and adsorbed onto silica nanoparticles was examined at three concentrations of cations: 10 and 100 mM of sodium and 100 mM of sodium to which 10 mM of calcium was added. The parameters investigated were the denaturation enthalpy (DeltaH), the temperature at which the denaturation transition was half-completed (T(m)), and the temperature range of the denaturation transition. For lysozyme and RNase, adsorption isotherms depend strongly on the ionic strength. At low ionic strength both proteins have a high affinity for the silica particles and adsorption is accompanied by a 15-25% reduction in DeltaH and a 3-6 degrees C decrease in T(m), indicating that the adsorbed state of the proteins is destabilized. Also, an increase in the width of the denaturation transition is observed, signifying a larger conformational heterogeneity of the surface bound proteins. At higher ionic strengths, both with and without the addition of calcium, no significant adsorption-induced alteration in DeltaH was observed for all three proteins. The addition of calcium, however, decreases the width of the denaturation transition for lysozyme and RNase in the adsorbed state. Copyright 2001 Academic Press.