A Wide-Bandwidth PVT-Reconfigurable CMOS Power Amplifier with an Integrated Tunable-Output Impedance Matching Network.

This paper proposes a wideband CMOS power amplifier (PA) with integrated digitally assisted wideband pre-distorter (DAWPD) and a transformer-integrated tunable-output impedance matching network. As a continuation of our previous research, which focused only on linearization tuning for wideband and PVT, this work emphasized improving the maximum output power, gain and PAE across the PVT variations while maintaining the linearity for a wide frequency bandwidth of 1 GHz. The DAWPD is employed at the driver stage to realize a pre-distorting characteristic for wideband linearization. The addition of the tunable-output impedance matching technique in this work provides stable output power, PAE and gain across the PVT variations, through which it improves the design's robustness, reliability and production yield. Fabricated in CMOS 130 nm with an 8-metal-layer process, the DAWPD-PA with tunable-output impedance matching can achieve an operating frequency bandwidth of 1 GHz from 1.7 to 2.7 GHz. The DAWPD-PA attained a maximum output power of 27 to 28 dBm with a peak PAE of 38.8 to 41.3%. The power gain achieved was 26.9 to 29.7 dB across the targeted frequencies. In addition, when measured with a 20 MHz LTE modulated signal, the DAWPD-PA achieved a linear output power and PAE of 24.0 to 25.1 dBm and 34.5 to 38.8% across the frequency, respectively. On top of that, in this study, the DAWPD-PA is proven to be resilient to process-voltage-temperature (PVT) variations, where it achieves stable performances via the utilization of the proposed tuning mechanisms, mainly contributed by the proposed transformer-integrated tunable-output impedance matching network.

A 53-µA-Quiescent 400-mA Load Demultiplexer Based CMOS Multi-Voltage Domain Low Dropout Regulator for RF Energy Harvester.

A low-power capacitorless demultiplexer-based multi-voltage domain low-dropout regulator (MVD-LDO) with 180 nm CMOS technology is proposed in this work. The MVD-LDO has a 1.5 V supply voltage headroom and regulates an output from four voltage domains ranging from 0.8 V to 1.4 V, with a high current efficiency of 99.98% with quiescent current of 53 µA with the aid of an integrated low-power demultiplexer controller which consumes only 68.85 pW. The fabricated chip has an area of 0.149 mm2 and can deliver up to 400 mA of current. The MVD-LDO's line and load regulations are 1.85 mV/V and 0.0003 mV/mA for the low-output voltage domain and 3.53 mV/V and 0.079 mV/mA for the high-output voltage domain. The LDO consumes only 174.5 µW in standby mode, making it suitable for integrating with an RF energy harvester chip to power sensor nodes.

CMOS Radio Frequency Energy Harvester (RFEH) with Fully On-Chip Tunable Voltage-Booster for Wideband Sensitivity Enhancement.

Radio frequency energy harvesting (RFEH) is one form of renewable energy harvesting currently seeing widespread popularity because many wireless electronic devices can coordinate their communications via RFEH, especially in CMOS technology. For RFEH, the sensitivity of detecting low-power ambient RF signals is the utmost priority. The voltage boosting mechanisms at the input of the RFEH are typically applied to enhance its sensitivity. However, the bandwidth in which its sensitivity is maintained is very poor. This work implements a tunable voltage boosting (TVB) mechanism fully on-chip in a 3-stage cross-coupled differential drive rectifier (CCDD). The TVB is designed with an interleaved transformer architecture where the primary winding is implemented to the rectifier, while the secondary winding is connected to a MOSFET switch that tunes the inductance of the network. The TVB enables the sensitivity of the rectifier to be maintained at 1V DC output voltage with a minimum deviation of -2 dBm across a wide bandwidth of 3 to 6 GHz of 5G New Radio frequency (5GNR) bands. A DC output voltage of 1 V and a peak PCE of 83% at 3 GHz for -23 dBm input power are achieved. A PCE of more than 50% can be maintained at the sensitivity point of 1 V with the aid of TVB. The proposed CCDD-TVB mechanism enables the CMOS RFEH to be operated for wideband applications with optimum sensitivity, DC output voltage, and efficiency.

Exploration of 2D Ti3C2 MXene for all solution processed piezoelectric nanogenerator applications.

A new 2D titanium carbide (Ti3C2), a low dimensional material of the MXene family has attracted remarkable interest in several electronic applications, but its unique structure and novel properties are still less explored in piezoelectric energy harvesters. Herein, a systematic study has been conducted to examine the role of Ti3C2 multilayers when it is incorporated in the piezoelectric polymer host. The 0.03 g/L of Ti3C2 has been identified as the most appropriate concentration to ensure the optimum performance of the fabricated device with a generated output voltage of about 6.0 V. The probable reasons might be due to the uniformity of nanofiller distribution in the polyvinylidene difluoride (PVDF) and the incorporation of Ti3C2 in a polymer matrix is found to enhance the ß-phase of PVDF and diminish the undesired α-phase configuration. Low tapping frequency and force were demonstrated to scavenge electrical energy from abundant mechanical energy resources particularly human motion and environmental stimuli. The fabricated device attained a power density of 14 µW.cm-2 at 10.8 MΩ of load resistor which is considerably high among 2D material-based piezoelectric nanogenerators. The device has also shown stable electrical performance for up to 4 weeks and is practically able to store energy in a capacitor and light up a LED. Hence, the Ti3C2-based piezoelectric nanogenerator suggests the potential to realize the energy harvesting application for low-power electronic devices.