ABSTRACT
Formamidinium lead iodide (FAPbI3)-based perovskite solar cells have gained immense popularity over the last few years within the perovskite research community due to their incredible opto-electronic properties and the record power conversion efficiencies (PCEs) achieved by the solar cells. However, FAPbI3 is vulnerable to phase transitions even at room temperature, which cause structural instability and eventual device failure during operation. We performed post-treatment of the FAPbI3 surface with octyl ammonium iodide (OAI) in order to stabilize the active phase and preserve the crystal structure of FAPbI3. The formation of a 2D perovskite at the interface depends on the stoichiometry of the precursor. By optimizing the precursor stoichiometry and the concentration of OAI, we observe a synergistic effect, which results in improved power conversion efficiencies, reaching the best values of 22% on a glass substrate. Using physical and detailed optical analysis, we verify the presence of the 2D layer on the top of the 3D surface of the perovskite film.
ABSTRACT
Optical and structural properties of a blend thin film of (1:1 wt.) of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) doped with iodine (I2) and then exposed to a stepwise heating were reported and compared with the properties of doped P3HT films. The UV-Vis(T) absorption measurements were performed in situ during annealing runs, at the precisely defined temperatures, in a range of 20-210 °C. It was demonstrated that this new method allows one to observe the changes of absorption spectra, connected with the iodine release and other structural processes upon annealing. In addition, the thermally-induced changes of the exciton bandwidth (W) and the absorption edge parameters, i.e., the energy gap (EG) and the Urbach energy (EU) were discussed in the context of different length of conjugation and the structural disorder in polymers and blends films. During annealing, several stages were distinguished and related to the following processes as: the iodine escape and an increase in P3HT crystallinity, the orderly stacking of polymer chains, the thermally inducted structural defects and the phase separation caused by an aggregation of PCBM in the polymer matrix. Moreover, the detailed X-ray diffraction studies, performed for P3HT and P3HT:PCBM films, before and after doping and then after their thermal treatment, allowed us to consider the structural changes of polymer and blend films. The effect of iodine content and the annealing process on the bulk heterojunction (BHJ) solar cells parameters was checked, by the impedance spectroscopy (IS) measurements and the J-V characteristics registration. All of the investigated P3HT:PCBM blend films showed the photovoltaic effect; the increase in power conversion efficiency (PCE) upon iodine doping was demonstrated.
ABSTRACT
Optical (UV-vis and photoluminescence) properties of two soluble organic molecules based on azomethines with benzothiazole core (BTA1 and BTA2) were reported. The structures of both compounds are characterized by means FTIR, (1)H NMR, and (13)C NMR spectroscopy and elemental analysis; the results show an agreement with the proposed structure. The investigated compounds emitted blue light. Influence of excitation wavelength and concentration on maximum and intensity of emission of BTA1 and BTA2 was found. Electrochemical properties of the compounds were studied by differential pulse voltammetry. Introduction of fluorine moieties (BTA1) resulted in lower energy band gap (E(g)) of approximately â¼0.5 eV, whereas BTA2 showed E(g) of â¼2.8 eV. The devices comprised of BTA1 with P3HT:PCBM (1:1:1) showed an open circuit voltage (V(OC)) of 0.40 V, a short circuit current (J(SC)) of 1.19 mA/cm(2), and a fill factor (FF) of 0.23, giving a power-conversion efficiency (PCE) of 0.10% under AM1.5 G irradiation (100 mW/cm(2)).
