Physical and Electrical Characterization of Synthesized Millimeter Size Single Crystal Graphene, Using Controlled Bubbling Transfer.

In this work, we have investigated the influence of the transfer process on the monocrystalline graphene in terms of quality, morphology and electrical properties by analyzing the data obtained from optical microscopy, scanning electron microscopy, Raman spectroscopy and electrical characterizations. The influence of Cu oxidation on graphene prior to the transfer is also discussed. Our results show that the controlled bubbling electrochemical delamination transfer is an easy and fast transfer technique suitable for transferring large single crystals graphene without degrading the graphene quality. Moreover, Raman spectroscopy investigation reveals that the Cu surface oxidation modifies the strain of the graphene film. We have observed that graphene laying on unoxidized Cu is subject to a biaxial strain in compression, while graphene on Cu oxide is subject to a biaxial strain in tension. However, after graphene was transferred to a host substrate, these strain effects were strongly reduced, leaving a homogeneous graphene on the substrate. The transferred single crystal graphene on silicon oxide substrate was used to fabricate transmission line method (TLM) devices. Electrical measurements show low contact resistance ~150 Ω·µm, which confirms the homogeneity and high quality of transferred graphene.

Cracking effects in squashable and stretchable thin metal films on PDMS for flexible microsystems and electronics.

Here, we study cracking of nanometre and sub-nanometre-thick metal lines (titanium, nickel, chromium, and gold) evaporated onto commercial polydimethylsiloxane (PDMS) substrates. Mechanical and electromechanical testing reveals potentially technologically useful effects by harnessing cracking. When the thin film metal lines are subjected to uniaxial longitudinal stretching, strain-induced cracks develop in the film. The regularity of the cracking is seen to depend on the applied longitudinal strain and film thickness-the findings suggest ordering and the possibility of creating metal mesas on flexible substrates without the necessity of lithography and etching. When the metal lines are aligned transversally to the direction of the applied strain, a Poisson effect-induced electrical 'self-healing' can be observed in the films. The Poisson effect causes process-induced cracks to short circuit, resulting in the lines being electrically conducting up to very high strains (~40%). Finally, cracking results in the observation of an enhanced transversal gauge factor which is ~50 times larger than the geometric gauge factor for continuous metal films-suggesting the possibility of high-sensitivity thin-film metal strain gauge flexible technology working up to high strains.

Mechanically robust 39 GHz cut-off frequency graphene field effect transistors on flexible substrates.

Graphene has been regarded as a promising candidate channel material for flexible devices operating at radio-frequency (RF). In this work we fabricated and fully characterized double bottom-gate graphene field effect transistors on flexible polymer substrates for high frequency applications. We report a record high as-measured current gain cut-off frequency (ft) of 39 GHz. The corresponding maximum oscillation frequency (fmax) is 13.5 GHz. These state of the art high frequency performances are stable against bending, with a typical variation of around 10%, for a bending radius of up to 12 mm. To demonstrate the reliability of our devices, we performed a fatigue stress test for RF-GFETs which were dynamically bend tested 1000 times at 1 Hz. The devices are mechanically robust, and performances are stable with typical variations of 15%. Finally we investigate thermal dissipation, which is a critical parameter for flexible electronics. We show that at the optimum polarization the normalized power dissipated by the GFETs is about 0.35 mW µm(-2) and that the substrate temperature is around 200 degree centigrade. At a higher power, irreversible degradations of the performances are observed. Our study on state of the art flexible GFETs demonstrates mechanical robustness and stability upon heating, two important elements to assess the potential of GFETs for flexible electronics.

Epitaxial graphene on 4H-SiC(0001) grown under nitrogen flux: evidence of low nitrogen doping and high charge transfer.

Nitrogen doping of graphene is of great interest for both fundamental research to explore the effect of dopants on a 2D electrical conductor and applications such as lithium storage, composites, and nanoelectronic devices. Here, we report on the modifications of the electronic properties of epitaxial graphene thanks to the introduction, during the growth, of nitrogen-atom substitution in the carbon honeycomb lattice. High-resolution transmission microscopy and low-energy electron microscopy investigations indicate that the nitrogen-doped graphene is uniform at large scale. The substitution of nitrogen atoms in the graphene planes was confirmed by high-resolution X-ray photoelectron spectroscopy, which reveals several atomic configurations for the nitrogen atoms: graphitic-like, pyridine-like, and pyrrolic-like. Angle-resolved photoemission measurements show that the N-doped graphene exhibits large n-type carrier concentrations of 2.6 × 10(13) cm(-2), about 4 times more than what is found for pristine graphene, grown under similar pressure conditions. Our experiments demonstrate that a small amount of dopants (<1%) can significantly tune the electronic properties of graphene by shifting the Dirac cone about 0.3 eV toward higher binding energies with respect to the π band of pristine graphene, which is a key feature for envisioning applications in nanoelectronics.