Microstructure Evolution of the Near-Surface Deformed Layer and Corrosion Behavior of Hot Rolled AA7050 Aluminum Alloy.

The current study investigates the influence of hot rolling on the microstructure evolution of the near-surface region on AA7050 aluminum alloy and the corrosion performance of the alloy. It is revealed that hot rolling resulted in grain refinement in the near-surface region, caused by dynamic recrystallization, and equiaxed grains less than 500 nm can be clearly observed. Fibrous grains were evident in the hot rolled AA7050 aluminum alloy with relatively lower rolling temperature or larger rolling reduction, caused by the more severe elemental segregation at grain boundaries, which inhibited the progression of dynamic recrystallization. The density of the precipitates in the fibrous grain layer was higher, compared with those in the equiaxed grain layer, due to the increased dislocation density, combined with more severe elemental segregation, which significantly promoted the nucleation of precipitates. With the co-influence exerted by low density of precipitates and dislocations on the improvement of the corrosion performance of the alloy, the rolled AA7050 alloy with decreased density of precipitates and dislocations exhibited better corrosion resistance.

Preparation of Three-Dimensional MF/Ti3C2Tx/PmPD by Interfacial Polymerization for Efficient Hexavalent Chromium Removal.

Heavy metal pollution is a serious threat to human health and the ecological environment, but adsorption technology based on nano adsorbents can effectively treat the crisis. However, due to the nanoscale effect, nano adsorbents have some crucial shortcomings, such as recycling difficulty and the loss of nanoparticles, which seriously limit their application. The feasible assembly of nano adsorbents is an accessible technology in urgent need of a breakthrough. In this study, three-dimensional (3D) adsorbent (MF/Ti3C2Tx/PmPD) with excellent performance and favorable recyclability was prepared by interfacial polymerization with melamine foam (MF) as the framework, two-dimensional (2D) titanium carbide (Ti3C2Tx) as the bridge and Poly (m-Phenylenediamine) (PmPD) as the active nano component. The morphology, structure, mechanical property of MF/Ti3C2Tx/PmPD and reference MF/PmPD were investigated through a scanning electron microscope (SEM), Fourier transformed infrared spectra (FT-IR), Raman scattering spectra and a pressure-stress test, respectively. Owning to the regulation of Ti3C2Tx on the morphology and structure of PmPD, MF/Ti3C2Tx/PmPD showed excellent adsorption capacity (352.15 mg/g) and favorable cycling performance. R-P and pseudo-second-order kinetics models could well describe the adsorption phenomenon, indicating that the adsorption process involved a composite process of single-layer and multi-layer adsorption and was dominated by chemical adsorption. In this research, the preparation mechanism of MF/Ti3C2Tx/PmPD and the adsorption process of Cr(VI) were systematically investigated, which provided a feasible approach for the feasible assembly and application of nano adsorbents in the environmental field.

The Microstructure Evolution and Electrochemical Corrosion Behavior of 7A46 Aluminum Alloy in Different Quenching Conditions.

The quenching condition of aluminum alloy can affect the mechanical property and corrosion resistance of the profile. This paper is aimed at the low quench sensitivity of aluminum alloys. Scanning electron microscopy and transmission electron microscopy were used to analyze precipitate behaviors of the 7A46 aluminum alloy under different isothermal cooling conditions and microstructure evolutions of quench-induced precipitations. The effect of the different isothermal time on the corrosion resistance of the alloy, and the relationship between microstructure and corrosion resistance after quenching were revealed through electrochemical impedance spectroscopy and potentiodynamic polarization tests. Results show that corrosion sensitivity of the quenching-aged alloy is much higher than that of the double-aged (DA) alloy, and the corrosion resistance of the quenched alloy decreases firstly and then increases. Due to the high density of the matrix precipitates, the increased content of the impurity element, the discontinuity of the grain boundary precipitates and the widening of the precipitates free zone, the most serious degree of corrosion performance among the quenched alloys is 295 °C at 800 s, and the self-corrosion potential and self-current density is -0.919 V and 2.371 µA/cm2, respectively.

Improved intergranular corrosion resistance of Al-Mg-Mn alloys with Sc and Zr additions.

Al-5.8Mg-0.4Mn with minor alloying additions of Sc and Zr was investigated via electrochemical testing and nitric acid mass loss testing (NAMLT) in order to reveal the influence of Sc and Zr upon sensitization and intergranular corrosion. The Al-Mg-Mn alloys were also analysed using an electron probe microanalyzer, indicating that ß-phase (Al3Mg2) was more likely to precipitate around rectangular or cubic Al6Mn particles. Results reveal that the strength and intergranular corrosion resistance of Al-5.8Mg-0.4Mn was improved by the combined addition of Sc and Zr. The Al3(Sc1-xZrx) dispersoids can lead to an alteration of the relative proportion of low angle grain boundaries, and lower volume fraction of ß-phase was observed for Al-5.8Mg-0.4Mn-xSc-yZr relative to the Sc and Zr free alloy.

Structural modification of aluminum oxides for removing fluoride in water: crystal forms and metal ion doping.

In this paper, the effect of different crystal forms of Al2O3 on fluoride removal was studied. All crystal forms of Al2O3 were based on the same boehmite precursor and were obtained using a hydrothermal and calcination method. γ-Al2O3 had higher fluoride removal performance (52.15 mg/g) compared with θ-Al2O3 and α-Al2O3. Density functional theory (DFT) calculations confirmed that fluoride removal was greatest for γ-Al2O3, followed by θ-Al2O3 and α-Al2O3, and γ-Al2O3 possessed the strongest fluoride binding energy (-3.93 eV). The typical adsorption behaviour was consistent with the Langmuir model and pseudo-second-order model, indicating chemical and monolayer adsorption. Different metal ions were used to modify γ-Al2O3, and lanthanum had the best effect. Lanthanum oxide was shown to play an important role in fluoride removal. The best La/Al doping ratio was 20 At%. The adsorption process of the composite was also consistent with chemical and monolayer adsorption. When the La/Al doping rate was 20%, the adsorption capacity reached 94.64 mg/g. Compared with γ-Al2O3 (1.39 × 10-7 m/s), the adsorption rate of 20La-Al2O3 was 3.93 × 10-7 m/s according to the mass transfer model. Furthermore, DFT was used to provide insight into the adsorption mechanism, which was mainly driven by electrostatic attraction and ion exchange.

AtSTP8, an endoplasmic reticulum-localised monosaccharide transporter from Arabidopsis, is recruited to the extrahaustorial membrane during powdery mildew infection.

Biotrophic pathogens are believed to strategically manipulate sugar transport in host cells to enhance their access to carbohydrates. However, mechanisms of sugar translocation from host cells to biotrophic fungi such as powdery mildew across the plant-haustorium interface remain poorly understood. To investigate this question, systematic subcellular localisation analysis was performed for all the 14 members of the monosaccharide sugar transporter protein (STP) family in Arabidopsis thaliana. The best candidate AtSTP8 was further characterised for its transport properties in Saccharomyces cerevisiae and potential role in powdery mildew infection by gene ablation and overexpression in Arabidopsis. Our results showed that AtSTP8 was mainly localised to the endoplasmic reticulum (ER) and appeared to be recruited to the host-derived extrahaustorial membrane (EHM) induced by powdery mildew. Functional complementation assays in S. cerevisiae suggested that AtSTP8 can transport a broad spectrum of hexose substrates. Moreover, transgenic Arabidopsis plants overexpressing AtSTP8 showed increased hexose concentration in leaf tissues and enhanced susceptibility to powdery mildew. Our data suggested that the ER-localised sugar transporter AtSTP8 may be recruited to the EHM where it may be involved in sugar acquisition by haustoria of powdery mildew from host cells in Arabidopsis.

Computational and Experimental Insights into the Role of Acidic Molecules on the Corrosion Behavior on 7A46 Aluminum Alloy.

The corrosion mechanisms for different corrosive media on the aged 7A46 aluminum alloy were systematically investigated at nanoscale level. The combination of empirical intergranular and exfoliation corrosion behavior was employed, and coupled with first-principles calculations. Results revealed that the dispersed distribution of matrix precipitates (MPs) leads to the enhancement of the corrosion resistance pre-ageing (PA) followed by double-ageing (PA-DA) alloy. The deepest corrosion depth of PA-DA alloy was in hydrochloric acid, and the calculation result demonstrates that the passivation effect in combination with the accumulation of corrosion products in nitric acid protect the PA-DA alloy from further corrosion.

A Cu-only superoxide dismutase from stripe rust fungi functions as a virulence factor deployed for counter defense against host-derived oxidative stress.

Plants quickly accumulate reactive oxygen species (ROS) to resist against pathogen invasion, while pathogens strive to escape host immune surveillance by degrading ROS. However, the nature of the strategies that fungal pathogens adopt to counteract host-derived oxidative stress is manifold and requires deep investigation. In this study, a superoxide dismutase (SOD) from Puccinia striiformis f. sp. tritici (Pst) PsSOD2 with a signal peptide (SP) and the glycophosphatidyl inositol (GPI) anchor, strongly induced during infection, was analysed for its biological characteristics and potential role in wheat-Pst interactions. The results showed that PsSOD2 encodes a Cu-only SOD and responded to ROS treatment. Heterologous complementation assays in Saccharomyces cerevisiae suggest that the SP of PsSOD2 is functional for its secretion. Transient expression in Nicotiana benthamiana leaves revealed that PsSOD2 is localized to the plasma membrane. In addition, knockdown of PsSOD2 by host-induced gene silencing reduced Pst virulence and resulted in restricted hyphal development and increased ROS accumulation. In contrast, heterologous transient assays of PsSOD2 suppressed flg22-elicited ROS production. Taken together, our data indicate that PsSOD2, as a virulence factor, was induced and localized to the plasma membrane where it may function to scavenge host-derived ROS for promoting fungal infection.

Effect of the Zn/Mg Ratio on Microstructures, Mechanical Properties and Corrosion Performances of Al-Zn-Mg Alloys.

The effect of the Zn/Mg ratio on microstructures, mechanical properties and corrosion performances of Al-Zn-Mg alloys was studied. Microstructures were characterized using the optical microscope (OM), scanning electron microscope (SEM) and transmission electron microscope (TEM). Tensile tests, intergranular corrosion (IGC) and stress corrosion cracking (SCC) tests were conducted to study the properties. Microstructures results indicated that with the decrease of the Zn/Mg ratio, the recrystallization proportion and the fraction of second phase decreased, while the size of η' (MgZn2) phases in grain interior also significantly decreased. The number density of η' phases in grain interior increased and grain boundary precipitates developed discontinuous distribution with the decrease of the Zn/Mg ratio. These microstructures contributed to the significant improvement of the strength and corrosion resistance. The tensile strength and yield strength increased by 34.1% and 47.4%, respectively, with the Zn/Mg ratio decreased from 11.4 to 6.1. Calculating results indicated that the enhancement of strength mainly contributed from the solid-solution strengthening, grain-boundary strengthening and precipitation strengthening. The intergranular corrosion degree was greatly relieved and the stress corrosion sensitivity index decreased from 0.031 to 0.007 with the Zn/Mg ratio decreased from 11.4 to 6.1.

TaSTP13 contributes to wheat susceptibility to stripe rust possibly by increasing cytoplasmic hexose concentration.

BACKGROUND: Biotrophic fungi make intimate contact with host cells to access nutrients. Sugar is considered as the main carbon sources absorbed from host cells by pathogens. Partition, exchanges and competition for sugar at plant-pathogen interfaces are controlled by sugar transporters. Previous studies have indicated that the leaf rust resistance (Lr) gene Lr67, a natural mutation of TaSTP13 encoding a wheat sugar transport protein, confers partial resistance to all three wheat rust species and powdery mildew possibly due to weakened sugar transport activity of TaSTP13 by heterodimerization. However, one major problem that remains unresolved concerns whether TaSTP13 participates in wheat susceptibility to rust and mildew. RESULTS: In this study, expression of TaSTP13 was highly induced in wheat leaves challenged by Puccinia striiformis f. sp. tritici (Pst) and certain abiotic treatments. TaSTP13 was localized in the plasma membrane and functioned as homooligomers. In addition, a functional domain for its transport activity was identified in yeast. Suppression of TaSTP13 reduced wheat susceptibility to Pst by barley stripe mosaic virus-induced gene silencing (VIGS). While overexpression of TaSTP13 promoted Arabidopsis susceptibility to powdery mildew and led to increased glucose accumulation in the leaves. CONCLUSIONS: These results indicate that TaSTP13 is transcriptionally induced and contributes to wheat susceptibility to stripe rust, possibly by promoting cytoplasmic hexose accumulation for fungal sugar acquisition in wheat-Pst interactions.

Stabilization of arsenic sludge with mechanochemically modified zero valent iron.

Modified zero valent iron (ZVI) is obtained from commercial iron powder co-ground with manganese dioxide (MnO2) in intensive mechanical stress. The result indicates that the modified ZVI is very effective in arsenic sludge stabilization with a declination of arsenic leaching contraction from 72.50 mg/L to 0.62 mg/L, much lower than that of ordinary ZVI (10.48 mg/L). The involved process, including mechanochemical activation, corrosion and arsenic adsorption, is characterized explicitly to verify the improved arsenic stabilization mechanism. It shows that the mechanically formed Fe-Mn binary oxides layer results in an intensive corrosion extent, generating a mass of corrosion products. Moreover, as the emergence of Mn will restrain the process of iron (hydr)oxides crystallization, the ultimate corrosion products of the modified ZVI predominates in amorphous iron (hydr)oxides, performing much better in arsenic absorption. According to the BCR analysis, unstable arsenic in sludge is easily transformed to residual fraction by the help of amorphous iron (hydr)oxides, resulting in a restrained environmental availability of arsenic sludge after the modified ZVI stabilization.