Porcelain veneers as an alternative for esthetic treatment: clinical report.

This case report describes the restoration of the anterior dentition with porcelain laminate veneers. The advances in bonding of porcelain to tooth structure make this treatment a feasible alternative to restore teeth with alteration in shape and position in cases in which the esthetic demand is high. The rationale for various choices in this treatment protocol is detailed with reference to the pertinent literature. Thus, the clinical success of the technique depends on the correct identification of a case for which this treatment is appropriate and the successful execution of the clinical steps involved.

Selective enamel etching: effect on marginal adaptation of self-etch LED-cured bond systems in aged Class I composite restorations.

The aim of this study was to evaluate the influence of previous enamel etch and light emitting diode (LED) curing on gap formation of self-etch adhesive systems in Class I composite restorations after thermomechanical aging (TMA). Thus, on 192 human molars, a box-shaped Class I cavity was prepared maintaining enamel margins. Self-etch adhesives (Clearfil SE and Clearfil S3) were used to restore the preparation with a microhybrid composite. Before application of the adhesives, half of the teeth were enamel etched for 15 seconds with 37% phosphoric acid; the other half were not etched. For the photoactivation of the adhesives and composite, three light-curing units (LCUs) were used: one polywave (Ultra-Lume LED 5, UL) and two single-peak (FlashLite 1401, FL and Radii-cal, RD) LEDs. After this, epoxy resin replicas of the occlusal surface were made, and the specimens were submitted to TMA. New replicas were made from the aged specimens for marginal adaptation analysis by scanning electron microscopy. Data were submitted to Kruskal-Wallis and Wilcoxon tests (α=0.05). Before TMA, when enamel was etched before the application of S3, no gap formation was observed; however, there were gaps at the interface for the other tested conditions, with a statistical difference (p≤0.05). After TMA, the selective enamel etching previous to the S3 application, regardless of the LCU, promoted higher marginal adaptation compared to the other tested groups (p≤0.05). Prior to TMA, higher marginal integrity was observed, in comparison with specimens after TMA (p≤0.05). With regard to Clearfil SE and Clearfil Tri-S cured with FL, no differences of gap formation were found between before and after aging (5.3 ± 3.8 and 7.4 ± 7.5, respectively), especially when the Clearfil Tri-S was used in the conventional protocol. When cured with RD or UL and not etched, Clearfil Tri-S presented the higher gap formation. In conclusion, additional enamel etching promoted better marginal integrity for Clearfil Tri-S, showing it to be an efficient technique for Class I composite restorations. The two-step self-etch adhesive was not influenced by selective enamel etching or by the LED-curing unit.

Effect of different filling materials in combination with intraradicular posts on the resistance to fracture of weakened roots.

The preservation and restoration of severely weakened pulpless teeth is a difficult and relatively unpredictable procedure. This study evaluated the resistance to fracture of experimentally weakened bovine roots internally reconstructed with different filling materials in combination with prefabricated post compared with restored roots that were relatively intact. The roots of 75 mandibular bovine incisors with similar bulks were selected. Of these, 60 were internally prepared to standardized dimensions, thereby simulating weakness. All roots were filled with different restorative materials. The specimens were submitted to the fracture resistance testing with the application of a tangential compressive loading at an angle of 135 degrees in relation to the long axes of the roots. Results indicated statistically significant differences in relation to the root conditions. Weakened roots were less resistant to fracture than were controls. The roots restored with the resin cement demonstrated the lowest fracture resistance values, but statistically significant differences were observed only when compared with those restored by the resin-modified glass-ionomer cement. Resin-modified glass-ionomer cement, polyacid-modified resin composite and resin composite behaved similarly without statistically significant differences among them. None of the materials evaluated were capable of achieving the fracture resistance recorded for unweakened controls.

Effect of different filling materials in combination with intraradicular posts on the resistance to fracture of weakened roots / Efeito dos diferentes materiais obturados em combinação com pinos intra-radiculares na resistência da fratura de raízes frágeis

The preservation and restoration of severely weakened pulpless teeth is a difficult and relatively unpredictable procedure. This study evaluated the resistance to fracture of experimentally weakened bovine roots internally reconstructed with different filling materials in combination with prefabricated post compared with restored roots that were relatively intact. The roots of 75 mandibular bovine incisors with similar bulks were selected. Of these, 60 were internally prepared to standardized dimensions, thereby simulating weakness. All roots were filled with different restorative materials. The specimens were submitted to the fracture resistance testing with the application of a tangential compressive loading at an angle of 135 in relation to the long axes of the roots. Results indicated statistically significant differences in relation to the root conditions. Weakened roots were less resistant to fracture than were controls. The roots restored with the resin cement demonstrated the lowest fracture resistance values, but statistically significant differences were observed only when compared with those restored by the resin-modified glass-ionomer cement. Resin-modified glass-ionomer cement, polyacid-modified resin composite and resin composite behaved similarly without statistically significant differences among them. None of the materials evaluated were capable of achieving the fracture resistance recorded for unweakened controls