An (Eco)Toxicity Life Cycle Impact Assessment Framework for Per- And Polyfluoroalkyl Substances.

A framework for characterizing per- and polyfluoroalkyl substances (PFASs) in life cycle impact assessment (LCIA) is proposed. Thousands of PFASs are used worldwide, with special properties imparted by the fluorinated alkyl chain. Our framework makes it possible to characterize a large part of the family of PFASs by introducing transformation fractions that translate emissions of primary emitted PFASs into the highly persistent terminal degradation products: the perfluoroalkyl acids (PFAAs). Using a PFAA-adapted characterization model, human toxicity as well as marine and freshwater aquatic ecotoxicity characterization factors are calculated for three PFAAs, namely perfluorooctanoic acid (PFOA) perfluorohexanoic acid (PFHxA) and perfluorobutanesulfonic acid (PFBS). The model is evaluated to adequately capture long-term fate, where PFAAs are predicted to accumulate in open oceans. The characterization factors of the three PFAAs are ranked among the top 5% for marine ecotoxicity, when compared to 3104 chemicals in the existing USEtox results databases. Uncertainty analysis indicates potential for equally high ranks for human health impacts. Data availability constitutes an important limitation creating uncertainties. Even so, a life cycle assessment (LCA) case study illustrates practical application of our proposed framework, demonstrating that even low emissions of PFASs can have large effects on LCA results.

Combining in Silico Tools with Multicriteria Analysis for Alternatives Assessment of Hazardous Chemicals: A Case Study of Decabromodiphenyl Ether Alternatives.

Alternatives assessment is applied for minimizing the risk of unintentionally replacing a hazardous chemical with another hazardous chemical. Central challenges are the diversity of properties to consider and the lack of high-quality experimental data. To address this, a novel alternatives assessment procedure was developed based on in silico data and multicriteria decision analysis (MCDA) methods. As a case study, 16 alternatives to the flame retardant decabromodiphenyl ether were considered. The hazard properties included persistence (P), bioaccumulation potential (B), toxicities (T), and mobility in water (M). Databases were consulted and 2866 experimental data points were collected for the target chemicals; however, these were mostly replicate data points for some hazard criteria for a subset of alternatives. Therefore, in silico data and three MCDA strategies were tested including heat mapping, multiattribute utility theory (MAUT), and Elimination Et Choix Traduisant la REalité (ELECTRE III). The heat map clearly showed that none of the target chemicals are hazard-free, whereas MAUT and ELECTRE III agreed on ranking the "least worst" choices. This study identified several challenges and the complexity in the alternatives assessment processes motivating more case studies combining in silico and MCDA approaches.

Dissolved methane in the influent of three Australian wastewater treatment plants fed by gravity sewers.

Methane (CH4) is an important anthropogenic greenhouse gas and a by-product of urban sewage management. In recent years and contrary to international (IPCC) consensus, pressurised (anaerobic) sewers were identified as important CH4 sources, yet relatively little remains known regarding the role of gravity sewers in CH4 production and conveyance. Here we provide the results of a nine month study assessing dissolved CH4 levels in the raw influent of three large Australian wastewater treatment plants (WWTPs) fed by gravity sewers. Similar to recent international research and contrary to IPCC guidance, results show that gravity sewered wastewater contains moderate levels of CH4 (≈1mgL-1). Dissolved CH4 concentration correlated negatively with daily sewage flow rate (i.e. inversely proportional to sewer hydraulic residence time), with daily CH4 mass loads on average some two-fold greater under low flow (dry weather) conditions. Along with sewage hydraulic residence time, sewer sediments are thought to interact with sewage flow rate and are considered to play a key role in gravity sewer CH4 production. A per capita load of 78gCH4person-1y-1 is offered for gravity sewered wastewater entering WWTPs, with a corresponding emission estimate of up to 62gCH4person-1y-1, assuming 80% water-to-air transfer of inflowing CH4 in WWTPs with combined preliminary-primary plus secondary treatment. Results here support the emerging consensus view that hydraulic operation (i.e. gravity versus pressurised, sewage flow rate) is a key factor in determining sewer CH4 production, with gravity sewer segments likely to play a dominant role in total CH4 production potential for large metropolitan sewer networks. Further work is warranted to assess the scale and temporal dynamics of CH4 production in gravity sewers elsewhere, with more work needed to adequately capture and assess the scale of diffuse sewer network CH4 emissions from sprawling urban settlements globally.

Review of Environmental Assessment Case Studies Blending Elements of Risk Assessment and Life Cycle Assessment.

Risk assessment (RA) and life cycle assessment (LCA) are two analytical tools used to support decision making in environmental management. This study reviewed 30 environmental assessment case studies that claimed an integration, combination, hybridization, or complementary use of RA and LCA. The focus of the analysis was on how the respective case studies evaluated emissions of chemical pollutants and pathogens. The analysis revealed three clusters of similar case studies. Yet, there seemed to be little consensus as to what should be referred to as RA and LCA, and when to speak of combination, integration, hybridization, or complementary use of RA and LCA. This paper provides clear recommendations toward a more stringent and consistent use of terminology. Blending elements of RA and LCA offers multifaceted opportunities to adapt a given environmental assessment case study to a specific decision making context, but also requires awareness of several implications and potential pitfalls, of which six are discussed in this paper. To facilitate a better understanding and more transparent communication of the nature of a given case study, this paper proposes a "design space" (i.e., identification framework) for environmental assessment case studies blending elements of RA and LCA. Thinking in terms of a common design space, we postulate, can increase clarity and transparency when communicating the design and results of a given assessment together with its potential strengths and weaknesses.

Including pathogen risk in life cycle assessment of wastewater management. 2. Quantitative comparison of pathogen risk to other impacts on human health.

Resource recovery from sewage sludge has the potential to save natural resources, but the potential risks connected to human exposure to heavy metals, organic micropollutants, and pathogenic microorganisms attract stakeholder concern. The purpose of the presented study was to include pathogen risks to human health in life cycle assessment (LCA) of wastewater and sludge management systems, as this is commonly omitted from LCAs due to methodological limitations. Part 1 of this article series estimated the overall pathogen risk for such a system with agricultural use of the sludge, in a way that enables the results to be integrated in LCA. This article (part 2) presents a full LCA for two model systems (with agricultural utilization or incineration of sludge) to reveal the relative importance of pathogen risk in relation to other potential impacts on human health. The study showed that, for both model systems, pathogen risk can constitute an important part (in this study up to 20%) of the total life cycle impacts on human health (expressed in disability adjusted life years) which include other important impacts such as human toxicity potential, global warming potential, and photochemical oxidant formation potential.

Including pathogen risk in life cycle assessment of wastewater management. 1. Estimating the burden of disease associated with pathogens.

The environmental performance of wastewater and sewage sludge management is commonly assessed using life cycle assessment (LCA), whereas pathogen risk is evaluated with quantitative microbial risk assessment (QMRA). This study explored the application of QMRA methodology with intent to include pathogen risk in LCA and facilitate a comparison with other potential impacts on human health considered in LCA. Pathogen risk was estimated for a model wastewater treatment system (WWTS) located in an industrialized country and consisting of primary, secondary, and tertiary wastewater treatment, anaerobic sludge digestion, and land application of sewage sludge. The estimation was based on eight previous QMRA studies as well as parameter values taken from the literature. A total pathogen risk (expressed as burden of disease) on the order of 0.2-9 disability-adjusted life years (DALY) per year of operation was estimated for the model WWTS serving 28,600 persons and for the pathogens and exposure pathways included in this study. The comparison of pathogen risk with other potential impacts on human health considered in LCA is detailed in part 2 of this article series.

Methodological issues in life cycle assessment of mixed-culture polyhydroxyalkanoate production utilising waste as feedstock.

Assessing the environmental performance of emerging technologies using life cycle assessment (LCA) can be challenging due to a lack of data in relation to technologies, application areas or other life cycle considerations, or a lack of LCA methodology that address the specific concerns. Nevertheless, LCA can be a valuable tool in the environmental optimisation in the technology development phase. One emerging technology is the mixed-culture production of polyhydroxyalkanoates (PHAs). PHA production by pure microbial cultures has been developed and assessed in several LCAs during the previous decade. Recent developments within mixed-culture PHA production call for environmental assessment to guide in technology development. Mixed-culture PHA production can use the organic content in wastewater as a feedstock; the production may then be integrated with wastewater treatment (WWT) processes. This means that mixed-culture PHA is produced as a by-product from services in the WWT. This article explores different methodological challenges for LCA of mixed-culture PHA production using organic material in wastewater as feedstock. LCAs of both pure- and mixed-culture PHA production were reviewed. Challenges, similarities and differences when assessing PHA production by mixed- or pure-cultures were identified and the resulting implications for methodological choices in LCA were evaluated and illustrated, using a case study with mixed- and pure-culture PHA model production systems, based on literature data. Environmental impacts of processes producing multiple products or services need to be allocated between the different products or services. Such situations occur both in feedstock production and when the studied system is providing multiple functions. The selection of allocation method is shown to determine the LCA results. The type of data used, for electricity in the energy system, is shown to be important for the results, which indicates, a strong regional dependency of results for systems with electricity use as an environmental hot spot. The importance of assessing water use, an environmental impact not assessed by any of the reviewed studies, is highlighted.

Municipal gravity sewers: an unrecognised source of nitrous oxide.

Nitrous oxide (N2O) is a primary ozone-depleting substance and powerful greenhouse gas. N2O emissions from secondary-level wastewater treatment processes are relatively well understood as a result of intensive international research effort in recent times, yet little information exists to date on the role of sewers in wastewater management chain N2O dynamics. Here we provide the first detailed assessment of N2O levels in the untreated influent (i.e. sewer network effluent) of three large Australian metropolitan wastewater treatment plants. Contrary to current international (IPCC) guidance, results show gravity sewers to be a likely source of N2O. Results from the monitoring program revealed hydraulic flow rate as a strong driver for N2O generation in gravity sewers, with microbial processes (nitrification and possibly denitrification) implicated as the main processes responsible for its production. Results were also used to develop a presumptive emission factor for N2O in the context of municipal gravity sewers. Considering the discrepancy with current IPCC Guidelines, further work is warranted to assess the scale and dynamics of N2O production in sewers elsewhere.

Life cycle assessment of pig slurry treatment technologies for nutrient redistribution in Denmark.

Animal slurry management is associated with a range of impacts on fossil resource use and the environment. The impacts are greatest when large amounts of nutrient-rich slurry from livestock production cannot be adequately utilised on adjacent land. To facilitate nutrient redistribution, a range of different technologies are available. This study comprised a life cycle assessment of the environmental impacts from handling 1000 kg of pig slurry ex-animal. Application of untreated pig slurry onto adjacent land was compared with using four different treatment technologies to enable nutrient redistribution before land application: (a) separation by mechanical screw press, (b) screw press separation with composting of the solid fraction, (c) separation by decanter centrifuge, and (d) decanter centrifuge separation with ammonia stripping of the liquid fraction. Emissions were determined based on a combination of values derived from the literature and simulations with the Farm-N model for Danish agricultural and climatic conditions. The environmental impact categories assessed were climate change, freshwater eutrophication, marine eutrophication, terrestrial acidification, natural resource use, and soil carbon, nitrogen and phosphorus storage. In all separation scenarios, the liquid fraction was applied to land on the pig-producing (donor) farm and the solid fraction transported to a recipient farm and utilised for crop production. Separation, especially by centrifuge, was found to result in a lower environmental impact potential than application of untreated slurry to adjacent land. Composting and ammonia stripping either slightly increased or slightly decreased the environmental impact potential, depending on the impact category considered. The relative ranking of scenarios did not change after a sensitivity analysis in which coefficients for field emissions of nitrous oxide, ammonia and phosphorus were varied within the range cited in the literature. Therefore, the best technology to implement in a given situation depends on the environmental problem in question, local policy, cost and practicality.

Understanding the impacts of allocation approaches during process-based life cycle assessment of water treatment chemicals.

Chemicals are an important component of advanced water treatment operations not only in terms of economics but also from an environmental standpoint. Tools such as life cycle assessment (LCA) are useful for estimating the environmental impacts of water treatment operations. At the same time, LCA analysts must manage several fundamental and as yet unresolved methodological challenges, one of which is the question of how best to "allocate" environmental burdens in multifunctional processes. Using water treatment chemicals as a case study example, this article aims to quantify the variability in greenhouse gas emissions estimates stemming from methodological choices made in respect of allocation during LCA. The chemicals investigated and reported here are those most important to coagulation and disinfection processes, and the outcomes are illustrated on the basis of treating 1000 ML of noncoagulated and nondisinfected water. Recent process and economic data for the production of these chemicals is used and methodological alternatives for solving the multifunctionality problem, including system expansion and mass, exergy, and economic allocation, are applied to data from chlor-alkali plants. In addition, Monte Carlo simulation is included to provide a comprehensive picture of the robustness of economic allocation results to changes in the market price of these industrial commodities. For disinfection, results demonstrate that chlorine gas has a lower global warming potential (GWP) than sodium hypochlorite regardless of the technique used to solve allocation issues. For coagulation, when mass or economic allocation is used to solve the multifunctionality problem in the chlor-alkali facility, ferric chloride was found to have a higher GWP than aluminum sulfate and a slightly lower burden where system expansion or exergy allocation are applied instead. Monte Carlo results demonstrate that when economic allocation is used, GWP results were relatively robust and resilient to the changes in commodity prices encountered during the study period, with standard deviations less than 6% for all chlor-alkali-produced chemicals reported here. Overall outcomes from the study demonstrate the potential variability in LCA results according to the allocation approach taken and emphasize the need for a consensus approach to water sector LCAs.

Aggregating sustainability indicators: beyond the weighted sum.

Sustainability analysts and environmental decision makers often overcome the difficulty of interpreting comprehensive environmental profiles by aggregating the results using multi-criteria decision analysis (MCDA) methods. However, the wide variety of methodological approaches to weighting and aggregation introduces subjectivity and often uncertainty. It is important to select an approach that is consistent with the decision maker's information needs, but scant practical guidance is available to environmental managers on how to do this. In this paper, we aim to clarify the theoretical implications of an analyst's choice of MCDA method. By systematically examining the methodological decisions that must be made by the analyst at each stage of the assessment process, we aim to improve analysts' understanding of the relationship between MCDA theory and practice, and enable them to apply methods that are consistent with a decision maker's needs in any given problem context.

A streamlined sustainability assessment tool for improved decision making in the urban water industry.

Water supply is a key consideration in sustainable urban planning. Ideally, detailed quantitative sustainability assessments are undertaken during the planning stage to inform the decision-making process. In reality, however, the significant time and cost associated with undertaking such detailed environmental and economic assessments is often cited as a barrier to wider implementation of these key decision support tools, particularly for decisions made at the local or regional government level. In an attempt to overcome this barrier of complexity, 4 water service providers in Melbourne, Australia, funded the development of a publicly available streamlined Environmental Sustainability Assessment Tool, which is aimed at a wide range of decision makers to assist them in broadening the type and number of water servicing options that can be considered for greenfield or backlog developments. The Environmental Sustainability Assessment Tool consists of a simple user interface and draws on life cycle inventory data to allow for rapid estimation of the environmental and economic performance of different water servicing scenarios. Scenario options can then be further prioritized by means of an interactive multicriteria analysis. The intent of this article is to identify the key issues to be considered in a streamlined sustainability assessment tool for the urban water industry, and to demonstrate the feasibility of generating accurate life cycle assessments and life cycle costings, using such a tool. We use a real-life case study example consisting of 3 separate scenarios for a planned urban development to show that this kind of tool can emulate life cycle assessments and life cycle costings outcomes obtained through more detailed studies. This simplified approach is aimed at supporting "sustainability thinking" early in the decision-making process, thereby encouraging more sustainable water and sewerage infrastructure solutions.

Red meat production in australia: life cycle assessment and comparison with overseas studies.

Greenhouse gas emissions from beef production are a significant part of Australia's total contribution to climate change. For the first time an environmental life cycle assessment (LCA) hybridizing detailed on-site process modeling and input-output analysis is used to describe Australian red meat production. In this paper we report the carbon footprint and total energy consumption of three supply chains in three different regions in Australia over two years. The greenhouse gas (GHG) emissions and energy use data are compared to those from international studies on red meat production, and the Australian results are either average or below average. The increasing proportion of lot-fed beef in Australia is favorable, since this production system generates lower total GHG emissions than grass-fed production; the additional effort in producing and transporting feeds is effectively offset by the increased efficiency of meat production in feedlots. In addition to these two common LCA indicators, in this paper we also quantify solid waste generation and a soil erosion indicator on a common basis.

Monitoring bacterial indicators and pathogens in cattle feedlot waste by real-time PCR.

Quantitative microbial health risk assessment requires accurate enumeration of pathogens in hazard-containing matrices as part of the risk characterization process. As part of a risk management-oriented study of cattle feedlot waste contaminants, we investigated the utility of quantitative real-time PCR (qPCR) for surveying the microbial constituents of different faecal wastes. The abundance of Escherichia coli and enterococci were first estimated in five cattle feedlot waste types from five localities. Bacteria were quantified using two culture methods and compared to the number of genome copies detected by qPCR targeted at E. coli and Enterococcus faecalis. Bacterial numbers detected in the different wastes (fresh faeces, pen manure, aged manure, composted manure, carcass manure compost) ranged from 10-(7) to 10(2)g(-1) (dry weight). Both indicator groups were detected by qPCR with a comparable sensitivity to culture methods across this range. qPCR measurements of E. coli and E. faecalis correlated well with MPN and spread plate data. As a second comparison, we inoculated green fluorescent protein (GFP) labeled reference bacteria into manure samples. GFP labeled E. coli and Listeria monocytogenes were detected by qPCR in concentrations corresponding to between 18% and 71% of the initial bacterial numbers, compared to only 2.5-16% by plating. Our results supported our selection of qPCR as a fast, accurate and reliable system for surveying the presence and abundance of pathogens in cattle waste.

Environmental comparison of biosolids management systems using life cycle assessment.

To fill a gap in the information available to nonmetropolitan policy makers, eight scenarios combining processing technologies and end-uses for biosolids products associated with a 40,000 equivalent-person town were modeled using environmental life cycle assessment (LCA). An uncertainty analysis examined several key assumptions. The results showed that the reuse of biosolids products can be environmentally beneficial but transportation distances can change the preferences between technologies, and drying biosolids using petrochemical methane rather than biogas (produced endogenously in the wastewater facility) significantly worsens environmental performance. System scale can also invert option preferences. This work demonstrates an application of LCA to a strategic engineering question. We also examine the methodological feasibility of considering carbon sequestration and water offsets beyond those typical of previous studies. As the development of scientific data regarding the benefits of biosolids recycling develops,there may be potentialto reward agricultural businesses that choose to reduce their environmental burdens using biosolids. A life cycle management approach to this will be necessary.

Life cycle assessment for sustainable metropolitan water systems planning.

Life Cycle Assessment (LCA) is useful as an information tool for the examination of alternative future scenarios for strategic planning. Developing a life cycle assessment for a large water and wastewater system involves making methodological decisions about the level of detail which is retained through different stages of the process. In this article we discuss a methodology tailored to strategic planning needs which retains a high degree of model segmentation in order to enhance modeling of a large, complex system. This is illustrated by a case study of Sydney Water, which is Australia's largest water service provider. A prospective LCA was carried out to examine the potential environmental impacts of Sydney Water's total operations in the year 2021. To our knowledge this is the first study to create an LCA model of an integrated water and wastewater system with this degree of complexity. A "base case" system model was constructed to represent current operating assets as augmented and upgraded to 2021. The base case results provided a basis for the comparison of alternative future scenarios and for conclusions to be drawn regarding potential environmental improvements. The scenarios can be roughly classified in two categories: (1) options which improve the environmental performance across all impact categories and (2) options which improve one indicator and worsen others. Overall environmental improvements are achieved in all categories by the scenarios examining increased demand management, energy efficiency, energy generation, and additional energy recovery from biosolids. The scenarios which examined desalination of seawater and the upgrades of major coastal sewage treatment plants to secondary and tertiary treatment produced an improvement in one environmental indicator but deteriorations in all the other impact categories, indicating the environmental tradeoffs within the system. The desalination scenario produced a significant increase in greenhouse gas emissions due to coal-fired electricity generation for a small increase in water supply. Assessment of a greenfield scenario incorporating water demand management, on-site treatment, local irrigation, and centralized biosolids treatment indicates significant environmental improvements are possible relative to the assessment of a conventional system of corresponding scale.