Characterization of Glass-Ceramic Sealant for Solid Oxide Fuel Cells at Operating Conditions by Electrochemical Impedance Spectroscopy.

A commercially available glass-ceramic composition is applied on a ferritic stainless steel (FSS) substrate reproducing a type of interface present in solid oxide fuel cells (SOFCs) stacks. Electrochemical impedance spectroscopy (EIS) is used to study the electrical response of the assembly in the temperature range of 380-780 °C and during aging for 250 h at 780 °C. Post-experiment analyses, performed by means of X-ray diffraction (XRD), and along cross-sections by scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) analysis, highlight the microstructural changes promoted by aging conditions over time. In particular, progressive crystallization of the glass-ceramic, high temperature corrosion of the substrate and diffusion of Fe and Cr ions from the FSS substrate into the sealant influence the electrical response of the system under investigation. The electrical measurements show an increase in conductivity to 5 × 10-6 S∙cm-1, more than one order of magnitude below the maximum recommended value.

Morphological and chemical characteristics of different titanium surfaces treated by bicarbonate and glycine powder air abrasive systems.

OBJECTIVES: This in vitro study investigated possible morphological and chemical changes induced by glycine or sodium bicarbonate powder air polishing on machined and acid-etched titanium surfaces. MATERIALS AND METHODS: The glycine powder (granulometry <65 µm) and sodium bicarbonate powder (granulometry <150 µm) were applied on 2 machined healing abutments and on 2 acid-etched healing abutments. The samples were characterized by scanning electron microscopy coupled with energy dispersive x-ray spectroscopy. The analyses were performed at different steps: (1) as received, right after opening the abutment packaging; (2) after 20 minutes air exposure; (3) after aging in artificial saliva; (4) after glycine or sodium bicarbonate powder air polishing for 5 seconds; (5) after repetition of steps 3 and 4 with longer time of polishing (20 seconds). CONCLUSIONS: Air polishing using glycine and sodium bicarbonate powder seemed to be safe for professional oral hygiene of titanium dental implants, although acid-etched abutments and abutments treated with bicarbonate harbored more salts. This might indicate a greater plaque accumulation in a clinical situation. However, this result has to be investigated in vivo to understand its clinical relevance.

Archaeometallurgical characterization of the earliest European metal helmets.

Archaeometric analyses on conical and decorated cap helmets from the Bronze Age are presented. The helmets are dated to the 14-12th century BC according to associated finds in hoards. Alloy composition, material structure and manufacturing processes are determined and shed light on the earliest development of weaponry production in Central and Eastern Europe. Analyses were carried out using light and dark field microscopy, SEM-EDXS, PIXE, TOF-ND and PGAA. The results allowed reconstructing the manufacturing process, the differences between the cap of the helmets and their knobs (i.e. alloy composition) and the joining technique of the two parts.

Metallographic approach to the investigation of metallic archaeological objects.

Metallic objects are considered among the most significant findings in Cultural Heritage and represent the 'culture of Materials' and the habits of an historical period and of a population. They also preserve traces of time: from the transformation of the ores in metal (by smelting) to the degradation from metal to oxidised compounds (by corrosion processes). Metallography, historically devoted to connect the microstructural features to production processes and to chemical-physical-mechanical properties is a powerful and relatively easy approach to characterise metallic findings. All analytical tools and methods in the hands of a metallographer are improved through experience and practice and provide a large number of information (elemental composition, primary and secondary microstructures, surface treatments, corrosion rate, original ores traces) by the preparation of a fairly small microdestructive sample. A wise and careful use of the metallography allows the balance "object sacrifice/knowledge improvement" to lean on the right side contributing to the hard work of rebuilding humankind history. Beside a description of a research protocol some practical examples concerning archaeological findings are presented in this paper.

Metal objects mapping after small charge explosions. A study on AISI 304Cu steel with two different grain sizes.

Evidence of exposure of a metal component to a small charge explosion can be detected by observing microstructural modifications; they may be present even if the piece does not show noticeable overall plastic deformations. Particularly, if an austenitic stainless steel (or another metal having a face-centered cubic structure and a low stacking fault energy) is exposed to an explosive shock wave, high-speed deformation induces primarily mechanical twinning, whereas, in nonexplosive events, a lower velocity plastic deformation first induces slip. The occurrence of mechanical twins can be detected even if the surface is damaged or oxidized in successive events. In the present research, optical metallography (OM) and scanning electron microscopy (SEM), and scanning tunneling microscopy (STM) were used to detect microstructural modifications caused on AISI 304Cu steel disks by small-charge explosions. Spherical charges of 54.5 or 109 g TNT equivalent mass were used at explosive-to-target distances from 6.5 to 81.5 cm, achieving peak pressures from 160 to 0.5 MPa. Explosions induced limited or no macro-deformation. Two alloy grain sizes were tested. Surface OM and SEM evidenced partial surface melting, zones with recrystallization phenomena, and intense mechanical twinning, which was also detected by STM and X-ray diffraction. In the samples' interior, only twins were seen, up to some distance from the explosion impinged surface and again, at the shortest charge-to-sample distances, in a thin layer around the reflecting surface. For forensic science locating purposes after explosions, the maximum charge-to-target distance at which the phenomena disappear was singled out for each charge or grain size and related to the critical resolved shear stress for twinning.