ABSTRACT
The global climate change is mainly caused by carbon dioxide (CO2) emissions. To help reduce CO2 emissions and conserve thermal energy, sustainable materials based on flexible thermal insulation are developed to minimize heat flux, drawing inspiration from natural systems such as polar bear hairs. The unique structure of hollow double-shell fibers makes it possible to achieve low thermal conductivity in the material while retaining exceptional elasticity, allowing it to adapt to insulation systems of any shape. The layered system of porous mats reaches a thermal conductivity coefficient of 0.031 Wâm⻹âK⻹ and enables to reduce the heat transfer. The results achieved using scanning thermal microscopy (SThM) correlate with the simulated heat flow in the case of individual fibers. This research study brings new insights into the energy efficiency of domestic environments, thereby addressing the growing demand for sustainable and high-performance insulation materials for saving energy loss and reducing pollution footprint.
ABSTRACT
TiO2 was loaded on the porous nickel foam from the suspended ethanol solution and used for the photocatalytic removal of NOx. Such prepared material was heat-treated at various temperatures (400-600 °C) to increase the adhesion of TiO2 with the support. Obtained TiO2/nickel foam samples were characterized by XRD, UV-Vis/DR, FTIR, XPS, AFM, SEM, and nitrogen adsorption at 77 K. Photocatalytic tests of NO abatement were performed in the rectangular shape quartz reactor, irradiated from the top by UV LED light with an intensity of 10 W/m2. For these studies, a laminar flow of NO in the air (1 ppm) was applied under a relative humidity of 50% and a temperature of 28 °C. Concentrations of both NO and NO2 were monitored by a chemiluminescence NO analyzer. The adsorption of nitrogen species on the TiO2 surface was determined by FTIR spectroscopy. Performed studies revealed that increased temperature of heat treatment improves adhesion of TiO2 to the nickel foam substrate, decreases surface porosity, and causes removal of hydroxyl and alcohol groups from the titania surface. The less hydroxylated surface of TiO2 is more vulnerable to the adsorption of NO2 species, whereas the presence of OH groups on TiO2 enhances the adsorption of nitrate ions. Adsorbed nitrate species upon UV irradiation and moisture undergo photolysis to NO2. As a consequence, NO2 is released into the atmosphere, and the efficiency of NOx removal is decreasing. Photocatalytic conversion of NO to NO2 was higher for the sample heated at 400 °C than for that at 600 °C, although coverage of nickel foam by TiO2 was lower for the former one. It is stated that the presence of titania defects (Ti3+) at low temperatures of its heating enhances the adsorption of hydroxyl groups and the formation of hydroxyl radicals, which take part in NO oxidation. Contrary to that, the presence of titania defects in TiO2 through the formation of ilmenite structure (NiTiO3) in TiO2/nickel foam heated at 600 °C inhibits its photocatalytic activity. No less, the sample obtained at 600 °C indicated the highest abatement of NOx due to the high and stable adsorption of NO2 species on its surface.
ABSTRACT
The objective of this work was to obtain cement composites with low percolation thresholds, which would reduce the cost of graphite and maintain good mechanical properties. For this purpose, exfoliated graphite was used as a conductive additive, which was obtained by exfoliating the expanded graphite via ultrasonic irradiation in a water bath with surfactant. To obtain evenly distributed graphite particles, the exfoliated graphite was incorporated with the remaining surfactant into the matrix. This study is limited to investigating the influence of exfoliated graphite on the electrical and mechanical properties of cement mortars. The electrical conductivity of the composites was investigated to determine the percolation threshold. The flexural and compressive strength was tested to assess the mechanical properties. In terms of the practical applications of these composites, the piezoresistive, temperature-resistivity, and thermoelectric properties were studied. The results showed that the incorporation of exfoliated graphite with surfactant is an effective way to obtain a composite with a percolation threshold as low as 0.96% (total volume of the composite). In addition, the mechanical properties of the composites are satisfactory for practical application. These composites also have good properties in terms of practical applications. As a result, the exfoliated graphite used can significantly facilitate the practical use of smart composites.
ABSTRACT
The role of searching for industrial waste management solutions in construction is key for environmental protection. Research in recent years has focused on solutions aimed at reducing the carbon footprint. This paper presents the results of tests conducted on concrete reinforced with treated recycled tyre steel fibres (RTSFs) compared to the same amount of manufactured steel fibres (MSFs). The effectiveness of concrete reinforcement with RTSFs was analysed using the fracture mechanics parameters of cementitious composites. Rheological tests, residual flexural tensile strength tests, work of fracture measurements, toughness indices, examinations of the fibre distribution in the concrete, and SEM observations of the concrete fractures with fibres were performed. Determining the work of fracture and toughness indices was an innovative aspect of this paper. As the amount of RTSFs increased, a decrease in the consistency was observed, although the distribution of fibres in the concrete was uniform, as proven by the results of computer tomography tests. Concrete reinforced with RTSFs that is purified and refined during the recycling process might have better properties than concrete reinforced with the same amount of MSFs. The application of RTSFs in construction has environmental and economic benefits in addition to the strengthening of cementitious composites.
ABSTRACT
The study focused on determining color changes in materials made of cream-firing clays from the Opoczno region (Poland) due to the addition of calcium carbonate in the form of limestone. Moreover, the influence of the grain size distribution of this additive on the color properties of the materials and their phase composition was determined. Test samples were prepared using theplastic method and fired at four different temperatures: 1120, 1140, 1160 and 1180 °C. The color properties of the surface of ceramic materials were determined in CIE-Lab color space using a colorimeter. Quantitative phase analysis was performed using the Rietveld method. The research showed that the addition of calcium carbonate causes an increase in the yellow color factor and a decrease in the red color factor and the brightness of the material. Moreover, it was proven that the grain size distribution of the additive used significantly influences the phase composition of the materials, thus determining the values of physical properties and the color of the materials.
ABSTRACT
The paper presents the evaluation of the influence of calcium sulfate on the air void microstructure in concrete and its action mechanism depending on the character of the air-entraining agent. Gypsum dehydration has been previously proven to negatively influence the air void structure of air-entrained concrete. Ettringite, nucleating from tricalcium aluminate and calcium sulfate, influences the adsorption and mode of action of anionic-based polycarboxylate ether admixtures. The authors suspected the admixture's air-entraining mechanism was also affected by these characteristics. Gypsum dehydration was confirmed to influence the air void structure. In the case of the anionic surfactant, the content of air bubbles smaller than 300 µm was lower compared to cement with gypsum and hemihydrate. On the other hand, the content of air voids with a diameter up to 60 µm, which are the most favorable, was higher. The results obtained led to the conclusion that the mechanism of air entrainment was twofold, and in most cases occurred through the lowering of surface tension and/or through the adsorption of surfactant on cement grains. The adsorptive mechanism was proved to be more effective in terms of the total air content and the structure of the air void system. The results and conclusions of the study provide guidelines to determine the proper surfactant type to reduce the risk of improper air entrainment of concrete, and emphasize the importance of gypsum dehydration of cement in the process of air entrainment.
ABSTRACT
This study is focused on the behavior of the cream-firing clays from Opoczno region (Poland). The ceramic masses on which tests were carried out consisted of cream-firingBorkowice clay and dolomite in two different grain sizes as an additive that changes the color of ceramic materials. Test samples were prepared by plastic method and fired at range of 1100-1240 °C. Phase composition of theinvestigated materials was characterized by XRD method with quantitive analysis of the amorphous phase determined by the Retvield technique. Color properties of the surface of the obtained ceramic materials were determined in CIE-Lab color space. The phase composition of the obtained ceramics depends on the firing temperature. The color of the surface of the ceramic materials also depends on the firing temperature. There was a tendency to decrease the brightness, decrease the blue shade, and increase the yellow shade of the surface of materials with increasing the temperature. The conducted tests allowed to conclude that the color of ceramic materials depends on their phase composition. The most important role in the formation of color correspond to the amorphous phase, formed during the process. The lower content of the amorphous phase in the material allows to obtain brighter products with a lower proportion of yellow, and therefore closer to white. Moreover, following tests were carried out: total water absorption, total open porosity, linear shrinkage, and flexural strength. With increasing the temperature, total water absorption and total open porosity decrease, and total linear shrinkage increases due to the progressive sintering process. Flexural strength increases with the increase of the firing temperature for materials consisting of Borkowice clay. The addition of dolomite introduced new pores into the material, which resulted in an increase in flexural strength at lower firing temperatures and a decrease in flexural strength at higher firing temperatures.