Effect of Cellulose-Based Bioplastics on Current LDPE Recycling.

The increased use of bioplastics in the market has led to their presence in municipal solid waste streams alongside traditional fossil-based polymers, particularly low-density polyethylene (LDPE), which bioplastics often end up mixed with. This study aimed to assess the impact of cellulose acetate plasticized with triacetin (CAT) on the mechanical recycling of LDPE. LDPE-CAT blends with varying CAT content (0%, 1%, 5%, 7.5%, and 10% by weight) were prepared by melt extrusion and analyzed using scanning electron microscopy, Fourier-transform infrared spectroscopy, thermal analysis (thermogravimetric and differential scanning calorimetry), dynamic rheological measurements, and tensile tests. The results indicate that the presence of CAT does not significantly affect the chemical, thermal, and rheological properties of LDPE, and the addition of CAT at different levels does not promote LDPE degradation under typical processing conditions. However, the addition of CAT negatively impacts the processability and mechanical behavior of LDPE, resulting in the reduced quality of the recycled material. Thus, the presence of cellulose-based bioplastics in LDPE recycling streams should be avoided, and a specific sorting stream for bioplastics should be established.

Co-digestion of food waste and cellulose-based bioplastic: From batch to semi-continuous scale investigation.

Only few studies on the behaviour of bioplastics in anaerobic co-digestion could be found in literature and most of them are conducted in batch mode. Despite the fact that continuous experiments confirm or add new insight to the findings acquired from batch ones, there is still lack of such studies. This work aims to cover this gap, carrying out a semi-continuous anaerobic co-digestion of food waste and cellulose acetate (which its behaviour under anaerobic environment is also quite unexplored). After a first evaluation of the potential methane production from each substrate at batch scale, the semi-continuous co-digestion of food waste and cellulose acetate was carried out in three configurations. During the semi-continuous process, a methane yield of 331 NmlCH4/gVS was generated from the co-digestion of food waste and cellulose acetate while bioplastics specimens achieved a weight loss of about 45 %. The results were both lower than the one obtained from batch co-digestion, although methane production rates were comparable regardless of being fed with or without bioplastics. An increase was registered after 65 days of semi-continuous process, due to the accumulation of CA specimens. This confirms the different degradation trends between bioplastics and food waste.

Effects of cellulose-based bio-plastics on the aerobic biological stabilization treatment of mixed municipal solid waste: A lab-scale assessment.

The aim of this work is to assess how the presence of cellulose-based bio-plastics influence the biological stabilization of mixed Municipal Solid Waste (MSW). For the scope, two cellulose acetate bio-plastics have been mixed with a synthetic mixed waste to create samples with and without bio-plastics. A self-induced biostabilization has been carried out for 7 and 14 days where temperature and off-gas have been monitored continuously. Results about temperature evolution, O2 consumption, CO2 production and respiratory quotient did not show a substantial difference regarding both the duration of the process and the presence of cellulose-based bio-plastics on the mixture. On the average, the temperature peak and the maximum daily O2 consumption and CO2 production were 52.2 °C, 35.81 g O2/kg DM *d and 48.95 g CO2/kg DM *d respectively. Disintegration of bio-plastics samples after 7 and 14 days were comparable (on the average 23.13%). The self-induced biostabilization gave its main contribution after 4 days and resulted almost finished at the end of the day 7 of the process. Results showed that cellulose-based bio-plastics did not give a negative effect on mixed MSW biological stabilization and suggest a possible management, aiming at energy recovery of the outputs.

The influence of bio-plastics for food packaging on combined anaerobic digestion and composting treatment of organic municipal waste.

The use of bio-plastic-based packaging as an alternative to conventional plastic packaging is increasing. Among the plethora of different bio-based plastics, the most relevant ones are those that, at the end of their life, can be treated with the organic fraction of municipal solid waste. Even in these cases, their impact on the waste processing and recycling is not always positive. This study aim to assess on a laboratory scale the influence on combined anaerobic digestion and composting industrial processes of a bio-based plastic film, namely cellulose acetate (CA), in pure and modified (additions of additive) forms. CA films were mixed with organic waste and subjected to: (i) anaerobic digestion; (ii) active composting and (iii) two stages of curing composting. Anaerobic digestion and composting were monitored through methane yield and oxygen uptake respectively; additionally, the bio-plastics degree of disintegration was assessed during all the processes. The final disintegration of pure and modified CA was 73.82% and 54.66%, respectively. Anaerobic digestion contributes to the disintegration of the material, while aerobic treatment appears to be nearly ineffective, especially for modified CA. The presence of cellulose acetate during anaerobic digestion of food waste increased the methane yield by about 4.5%. Bioassay confirmed the absence of possible toxic effects on the final compost from the bio-plastic treatment. Although bio-based materials are not the only solution to plastic pollution, the findings confirm the need to upgrade the organic waste treatment plants and the necessity to revise the requirements for the use of compost in agriculture.

Decontamination and recycling of agrochemical plastic packaging waste.

Agrochemical containers shall undergo decontamination before being considered for recycling. This study provides an assessment on the feasibility of the triple-rinsing decontamination procedure, while evaluating the appropriateness of the material's quality for recycling. To achieve the objectives of the study, (1) the effectiveness of the decontamination procedure was investigated; (2) containers´ long storage times and changes on the polymer´s structure were assessed; and (3) the quality of the recycled material was tested. Results showed that the triple-rinsing procedure was ineffective for the container´s complete decontamination, yet a further washing step - performed during the simulation of the recycling process - allowed for an improved degree of decontamination for recycling. Photo-oxidation imposed significant changes on the chemical structure of the polymer, where the active ingredient could be detected by FTIR, even after the application of rinsing and extraction. The chemical structure of the bulk material has not changed, indicating that the pesticide mobilization was only confined to the surface. The mechanical tests showed material quality appropriateness, where tensile strength values were within the suggested ranges, providing a possibility for further utilization of this material when appropriate decontamination is applied.

The impact of collection portfolio expansion on key performance indicators of the Dutch recycling system for Post-Consumer Plastic Packaging Waste, a comparison between 2014 and 2017.

The recycling network of post-consumer plastic packaging waste (PCPPW) was studied for the Netherlands in 2017 with material flow analysis (MFA) and data reconciliation techniques. In comparison to the previous MFA of the PCPPW recycling network in 2014, the predominant change is the expansion of the collection portfolio from only plastic packages to plastic packages, beverage cartons and metal objects. The analysis shows that the amounts of recycled plastics products (as main washed milled goods) increased from 75 to 103 Gg net and the average polymeric purity of the recycled products remained nearly constant. Furthermore, the rise in the amounts of recycled products was accompanied with a rise in the total amount of rejected materials at cross docking facilities and sorting residues at the sorting facilities. This total amount grew from 19 Gg in 2014 to 70 Gg gross in 2017 and is over-proportional to the rise in recycled products. Hence, there is a clear trade-off between the growth in recycled plastics produced and the growth in rejects and residues. Additionally, since the polymeric purity of the recycled plastics did not significantly improve during the last years, most of the recycled plastics from PCPPW are still only suited for open-loop recycling. Although this recycling system for PCPPW is relatively advanced in Europe, it cannot be considered circular, since the net recycling yield is only 26 ±â€¯2% and the average polymeric purity of the recycled plastics is 90 ±â€¯7%.