ABSTRACT
This paper analyzes the field performance of two cup anemometers installed in Zaragoza (Spain). Data acquired over almost three years, from January 2015 to December 2017, were analyzed. The effect of the different variables (wind speed, temperature, harmonics, wind speed variations, etc.) on two cup anemometers was studied. Data analysis was performed with ROOT, an open-source scientific software toolkit developed by CERN (Conseil Européen pour la Recherche Nucléaire) for the study of particle physics. The effects of temperature, wind speed, and wind dispersion (as a first approximation to atmospheric turbulence) on the first and third harmonics of the anemometers' rotation speed (i.e., the anemometers' output signature) were studied together with their evolution throughout the measurement period. The results are consistent with previous studies on the influence of velocity, turbulence, and temperature on the anemometer performance. Although more research is needed to assess the effect of the anemometer wear and tear degradation on the harmonic response of the rotor's angular speed, the results show the impact of a recalibration on the performance of an anemometer by comparing this performance with that of a second anemometer.
Subject(s)
Software , Wind , Temperature , Data Analysis , SpainABSTRACT
This paper shows wind speed measurements from the TASEC-Lab experiment in a stratospheric balloon mission. The mission was launched in July 2021 from León (Spain) aerodrome. Measurements of horizontal wind speed in relation to the balloon gondola were successfully carried out with a cup anemometer. According to the available literature, this is the first time a cup anemometer has been used in a stratospheric balloon mission. The results indicate the need to consider the horizontal wind speed from the balloon ascent phase for thermal calculations of the mission.
ABSTRACT
This paper presents the development of the UPMSat-2 sun sensor, from the design to on-orbit operation. It also includes the testing of the instrument, one of the most important tasks that needs to be performed to operate a sensor with precision. The UPMSat-2 solar sensor has been designed, tested, and manufactured at the Universidad Politécnica de Madrid (UPM) using 3D printing and COTS (photodiodes). The work described in this paper was carried out by students and teachers of the Master in Space Systems (Máster Universitario en Sistemas Espaciales-MUSE). The solar sensor is composed of six photodiodes that are divided into two sets; each set is held and oriented on the satellite by its corresponding support printed in Delrin. The paper describes the choice of components, the electrical diagram, and the manufacture of the supports. The methodology followed to obtain the response curve of each photodiode is simple and inexpensive, as it requires a limited number of instruments and tools. The selected irradiance source was a set of red LEDs and halogen instead of an AM0 spectrum irradiance simulator. Some early results from the UPMSat-2 mission have been analyzed in the present paper. Data from magnetometers and the attitude control system have been used to validate the data obtained from the sun sensor. The results indicate a good performance of the sensors during flight, in accordance with the data from the ground tests.
ABSTRACT
Glass is a material that can be reused, except for a small part that, due to its residual characteristics, cannot be reused and becomes a nonbiodegradable waste to accumulate in landfills. The chemical composition and pozzolanic properties of waste glass are encouraging for the use of these wastes in the cement and concrete industries and for providing technically and environmentally viable solutions. In this study, we propose the production of deactivated concretes with a high content of glass powder in the binder. The substitution percentage of glass powder for cement used in this work was between 70% and 80%. Consistency, air content, bulk density, workability, compression strength, and permeability tests were performed. Regarding compressive strength, the results obtained at 90 days for percentages of cement substitution by glass powder of 70 and 80%, respectively, were 14.2 and 8.6. The chemical analysis of leachates showed concentrations of Fe, Cu, V, Ni, and Mo, in mg L-1, of 1.57, 1.38, 0.85, 0.95, and 0.44, respectively. The results obtained, compared with the relevant legislation, have proved that the inclusion of glass powder in a high percentage of substitution and with a granulometry of 20 µm in the manufacture of deactivated concretes is feasible for exterior pavements.
ABSTRACT
In this work, a new and low-cost Arduino-Based Data Acquisition System (ABDAS) for use in an aerodynamics lab is developed. Its design is simple and reliable. The accuracy of the system has been checked by being directly compared with a commercial and high accuracy level hardware from National Instruments. Furthermore, ABDAS has been compared to the accredited calibration system in the IDR/UPM Institute, its measurements during this testing campaign being used to analyzed two different cup anemometer frequency determination procedures: counting pulses and the Fourier transform. The results indicate a more accurate transfer function of the cup anemometers when counting pulses procedure is used.
ABSTRACT
A new, simple, and quick-calculation methodology to obtain a solar panel model, based on the manufacturers' datasheet, to perform MPPT simulations, is described. The method takes into account variations on the ambient conditions (sun irradiation and solar cells temperature) and allows fast MPPT methods comparison or their performance prediction when applied to a particular solar panel. The feasibility of the described methodology is checked with four different MPPT methods applied to a commercial solar panel, within a day, and under realistic ambient conditions.
ABSTRACT
Wind-flow pattern over embankments involves an overexposure of the rolling stock travelling on them to wind loads. Windbreaks are a common solution for changing the flow characteristic in order to decrease unwanted effects induced by the presence of cross-wind. The shelter effectiveness of a set of windbreaks placed over a railway twin-track embankment is experimentally analysed. A set of two-dimensional wind tunnel tests are undertaken and results corresponding to pressure tap measurements over a section of a typical high-speed train are herein presented. The results indicate that even small-height windbreaks provide sheltering effects to the vehicles. Also, eaves located at the windbreak tips seem to improve their sheltering effect.
Subject(s)
Models, Theoretical , WindABSTRACT
The results of several research campaigns investigating cup anemometer performance carried out since 2008 at the IDR/UPM Institute are included in the present paper. Several analysis of large series of calibrations were done by studying the effect of the rotor's geometry, climatic conditions during calibration, and anemometers' ageing. More specific testing campaigns were done regarding the cup anemometer rotor aerodynamics, and the anemometer signals. The effect of the rotor's geometry on the cup anemometer transfer function has been investigated experimentally and analytically. The analysis of the anemometer's output signal as a way of monitoring the anemometer status is revealed as a promising procedure for detecting anomalies.
ABSTRACT
The calibration coefficients of two commercial anemometers equipped with different rotors were studied. The rotor cups had the same conical shape, while the size and distance to the rotation axis varied. The analysis was based on the 2-cup positions analytical model, derived using perturbation methods to include second-order effects such as pressure distribution along the rotating cups and friction. The comparison with the experimental data indicates a nonuniform distribution of aerodynamic forces on the rotating cups, with higher forces closer to the rotating axis. The 2-cup analytical model is proven to be accurate enough to study the effect of complex forces on cup anemometer performance.
Subject(s)
Models, Theoretical , AlgorithmsABSTRACT
The effect of cup anemometer shape parameters, such as the cups' shape, their size, and their center rotation radius, was experimentally analyzed. This analysis was based on both the calibration constants of the transfer function and the most important harmonic term of the rotor's movement, which due to the cup anemometer design is the third one. This harmonic analysis represents a new approach to study cup anemometer performances. The results clearly showed a good correlation between the average rotational speed of the anemometer's rotor and the mentioned third harmonic term of its movement.
Subject(s)
Meteorology/instrumentation , Wind , Calibration , Equipment DesignABSTRACT
The influence of anemometer rotor shape parameters, such as the cups' front area or their center rotation radius on the anemometer's performance was analyzed. This analysis was based on calibrations performed on two different anemometers (one based on magnet system output signal, and the other one based on an opto-electronic system output signal), tested with 21 different rotors. The results were compared to the ones resulting from classical analytical models. The results clearly showed a linear dependency of both calibration constants, the slope and the offset, on the cups' center rotation radius, the influence of the front area of the cups also being observed. The analytical model of Kondo et al. was proved to be accurate if it is based on precise data related to the aerodynamic behavior of a rotor's cup.
