Bioinspired Lubricity from Surface Gel Layers.

Surface gel layers on commercially available contact lenses have been shown to reduce frictional shear stresses and mitigate damage during sliding contact with fragile epithelial cell layers in vitro. Spencer and co-workers recently demonstrated that surface gel layers could arise from oxygen-inhibited free-radical polymerization. In this study, polyacrylamide hydrogel shell probes (7.5 wt % acrylamide, 0.3 wt % N,N'-methylenebisacrylamide) were polymerized in three hemispherical molds listed in order of decreasing surface energy and increasing oxygen permeability: borosilicate glass, polyether ether ketone (PEEK), and polytetrafluoroethylene (PTFE). Hydrogel probes polymerized in PEEK and PTFE molds exhibited 100× lower elastic moduli at the surface (EPEEK* = 80 ± 31 and EPTFE* = 106 ± 26 Pa, respectively) than those polymerized in glass molds (Eglass* = 31,560 ± 1,570 Pa), in agreement with previous investigations by Spencer and co-workers. Biotribological experiments revealed that hydrogel probes with surface gel layers reduced frictional shear stresses against cells (τPEEK = 35 ± 15 and τPTFE = 22 ± 16 Pa) more than those without (τglass = 68 ± 15 Pa) and offered greater protection against cell damage when sliding against human telomerase-immortalized corneal epithelial (hTCEpi) cell monolayers. Our work demonstrates that the "mold effect" resulting in oxygen-inhibition polymerization creates hydrogels with surface gel layers that reduce shear stresses in sliding contact with cell monolayers, similar to the protection offered by gradient mucin gel networks across epithelial cell layers.

Experimental observation of near-wall effects during the puncture of soft solids.

Performing conventional mechanical characterization techniques on soft materials can be challenging due to issues such as limited sample volumes and clamping difficulties. Deep indentation and puncture is a promising alternative as it is an information-rich measurement with the potential to be performed in a high-throughput manner. Despite its promise, the method lacks standardized protocols, and open questions remain about its possible limitations. Addressing these shortcomings is vital to ensure consistent methodology, measurements, and interpretation across samples and labs. To fill this gap, we examine the role of finite sample dimensions (and by extension, volume) on measured forces to determine the sample geometry needed to perform and unambiguously interpret puncture tests. Through measurements of puncture on a well-characterized elastomer using systematically varied sample dimensions, we show that the apparent mechanical response of a material is in fact sensitive to near-wall effects, and that additional properties, such as the sliding friction coefficient, can only be extracted in the larger dimension case where such effects are negligible.

Survival-Associated Cellular Response Maintained in Pancreatic Ductal Adenocarcinoma (PDAC) Switched Between Soft and Stiff 3D Microgel Culture.

Pancreatic ductal adenocarcinoma (PDAC) accounts for about 90% of all pancreatic cancer cases. Five-year survival rates have remained below 12% since the 1970s, in part due to the difficulty in detection prior to metastasis (migration and invasion into neighboring organs and glands). Mechanical memory is a concept that has emerged over the past decade that may provide a path toward understanding how invading PDAC cells "remember" the mechanical properties of their diseased ("stiff", elastic modulus, E ≈ 10 kPa) microenvironment even while invading a healthy ("soft", E ≈ 1 kPa) microenvironment. Here, we investigated the role of mechanical priming by culturing a dilute suspension of PDAC (FG) cells within a 3D, rheologically tunable microgel platform from hydrogels with tunable mechanical properties. We conducted a suite of acute (short-term) priming studies where we cultured PDAC cells in either a soft (E ≈ 1 kPa) or stiff (E ≈ 10 kPa) environment for 6 h, then removed and placed them into a new soft or stiff 3D environment for another 18 h. Following these steps, we conducted RNA-seq analyses to quantify gene expression. Initial priming in the 3D culture showed persistent gene expression for the duration of the study, regardless of the subsequent environments (stiff or soft). Stiff 3D culture was associated with the downregulation of tumor suppressors (LATS1, BCAR3, CDKN2C), as well as the upregulation of cancer-associated genes (RAC3). Immunofluorescence staining (BCAR3, RAC3) further supported the persistence of this cellular response, with BCAR3 upregulated in soft culture and RAC3 upregulated in stiff-primed culture. Stiff-primed genes were stratified against patient data found in The Cancer Genome Atlas (TCGA). Upregulated genes in stiff-primed 3D culture were associated with decreased survival in patient data, suggesting a link between patient survival and mechanical priming.

Mechanical resilience of the sessile tunicate Botryllus schlosseri.

We demonstrate that the sessile tunicate Botryllus schlosseri is remarkably resilient to applied loads by attaching the animals to an extensile substrate subjected to quasistatic equiradial loads. Animals can withstand radial extension of the substrate to strain values as high as 20% before they spontaneously detach. In the small to moderate strain regime, we found no relationship between the dynamic size of the external vascular bed and the magnitude of applied stretch, despite known force sensitivities of the vascular tissue at the cellular level. We attribute this resilience to the presence and mechanical properties of the tunic, the cellulose-enriched gel-like substance that encases the animal bodies and surrounding vasculature.

In vitro models of soft tissue damage by implant-associated frictional shear stresses.

Silicone elastomer medical implants are ubiquitous in medicine, particularly for breast augmentation. However, when these devices are placed within the body, disruption of the natural biological interfaces occurs, which significantly changes the native energy-dissipation mechanisms of living systems. These new interfaces can introduce non-physiological contact pressures and tribological conditions that provoke inflammation and soft tissue damage. Despite their significance, the biotribological properties of implant-tissue and implant-extracellular matrix (ECM) interfaces remain poorly understood. Here, we developed an in vitro model of soft tissue damage using a custom-built in situ biotribometer mounted onto a confocal microscope. Sections of commercially-available silicone breast implants with distinct and clinically relevant surface roughness (Ra = 0.2 ± 0.03 µm, 2.7 ± 0.6 µm, and 32 ± 7.0 µm) were mounted to spherically-capped hydrogel probes and slid against collagen-coated hydrogel surfaces as well as healthy breast epithelial (MCF10A) cell monolayers to model implant-ECM and implant-tissue interfaces. In contrast to the "smooth" silicone implants (Ra < 10 µm), we demonstrate that the "microtextured" silicone implant (10 < Ra < 50 µm) induced higher frictional shear stress (τ > 100 Pa), which led to greater collagen removal and cell rupture/delamination. Our studies may provide insights into post-implantation tribological interactions between silicone breast implants and soft tissues.

Designing Superlubricious Hydrogels from Spontaneous Peroxidation Gradients.

Hydrogels are hydrated three-dimensional networks of hydrophilic polymers that are commonly used in the biomedical industry due to their mechanical and structural tunability, biocompatibility, and similar water content to biological tissues. The surface structure of hydrogels polymerized through free-radical polymerization can be modified by controlling environmental oxygen concentrations, leading to the formation of a polymer concentration gradient. In this work, 17.5 wt % polyacrylamide hydrogels are polymerized in low (0.01 mol % O2) and high (20 mol % O2) oxygen environments, and their mechanical and tribological properties are characterized through microindentation, nanoindentation, and tribological sliding experiments. Without significantly reducing the elastic modulus of the hydrogel (E* ≈ 200 kPa), we demonstrate an order of magnitude reduction in friction coefficient (from µ = 0.021 ± 0.006 to µ = 0.002 ± 0.001) by adjusting polymerization conditions (e.g., oxygen concentration). A quantitative analytical model based on polyacrylamide chemistry and kinetics was developed to estimate the thickness and structure of the monomer conversion gradient, termed the "surface gel layer". We find that polymerizing hydrogels at high oxygen concentrations leads to the formation of a preswollen surface gel layer that is approximately five times thicker (t ≈ 50 µm) and four times less concentrated (≈ 6% monomer conversion) at the surface prior to swelling compared to low oxygen environments (t ≈ 10 µm, ≈ 20% monomer conversion). Our model could be readily modified to predict the preswollen concentration profile of the polyacrylamide gel surface layer for any reaction conditions─monomer and initiator concentration, oxygen concentration, reaction time, and reaction media depth─or used to select conditions that correspond to a certain desired surface gel layer profile.

Silicone Implant Surface Roughness, Friction, and Wear.

Textured silicone breast implants with high average surface roughness ("macrotextured") have been associated with a rare cancer of the immune system, Breast Implant-Associated Anaplastic Large Cell Lymphoma (BIA-ALCL). Silicone elastomer wear debris may lead to chronic inflammation, a key step in the development of this cancer. Here, we model the generation and release of silicone wear debris in the case of a folded implant-implant ("shell-shell") sliding interface for three different types of implants, characterized by their surface roughness. The "smooth" implant shell with the lowest average surface roughness tested (Ra = 2.7 ± 0.6 µm) resulted in average friction coefficients of µavg = 0.46 ± 0.11 across 1,000 mm of sliding distance and generated 1,304 particles with an average particle diameter of Davg = 8.3 ± 13.1 µm. The "microtextured" implant shell (Ra = 32 ± 7.0 µm) exhibited µavg = 1.20 ± 0.10 and generated 2,730 particles with Davg = 4.7 ± 9.1 µm. The "macrotextured" implant shell (Ra = 80 ± 10 µm) exhibited the highest friction coefficients, µavg = 2.82 ± 0.15 and the greatest number of wear debris particles, 11,699, with an average particle size of Davg = 5.3 ± 3.3 µm. Our data may provide guidance for the design of silicone breast implants with lower surface roughness, lower friction, and smaller quantities of wear debris.

Superlubricity of pH-responsive hydrogels in extreme environments.

Poly(acrylamide-co-acrylic acid) (P(AAm-co-AA)) hydrogels are highly tunable and pH-responsive materials frequently used in biomedical applications. The swelling behavior and mechanical properties of these gels have been extensively characterized and are thought to be controlled by the protonation state of the acrylic acid (AA) through the regulation of solution pH. However, their tribological properties have been underexplored. Here, we hypothesized that electrostatics and the protonation state of AA would drive the tribological properties of these polyelectrolyte gels. P(AAm-co-AA) hydrogels were prepared with constant acrylamide (AAm) concentration (33 wt%) and varying AA concentration to control the amount of ionizable groups in the gel. The monomer:crosslinker molar ratio (200:1) was kept constant. Hydrogel swelling, stiffness, and friction behavior were studied by systematically varying the acrylic acid (AA) concentration from 0-12 wt% and controlling solution pH (0.35, 7, 13.8) and ionic strength (I = 0 or 0.25 M). The stiffness and friction coefficient of bulk hydrogels were evaluated using a microtribometer and borosilicate glass probes as countersurfaces. The swelling behavior and elastic modulus of these polyelectrolyte hydrogels were highly sensitive to solution pH and poorly predicted the friction coefficient (µ), which decreased with increasing AA concentration. P(AAm-co-AA) hydrogels with the greatest AA concentrations (12 wt%) exhibited superlubricity (µ = 0.005 ± 0.001) when swollen in unbuffered, deionized water (pH = 7, I = 0 M) and 0.5 M NaOH (pH = 13.8, I = 0.25 M) (µ = 0.005 ± 0.002). Friction coefficients generally decreased with increasing AA and increasing solution pH. We postulate that tunable lubricity in P(AAm-co-AA) gels arises from changes in the protonation state of acrylic acid and electrostatic interactions between the probe and hydrogel surface.

Extracellular Optogenetics at the Interface of Synthetic Biology and Materials Science.

We review fundamental mechanisms and applications of OptoGels: hydrogels with light-programmable properties endowed by photoswitchable proteins ("optoproteins") found in nature. Light, as the primary source of energy on earth, has driven evolution to develop highly-tuned functionalities, such as phototropism and circadian entrainment. These functions are mediated through a growing family of optoproteins that respond to the entire visible spectrum ranging from ultraviolet to infrared by changing their structure to transmit signals inside of cells. In a recent series of articles, engineers and biochemists have incorporated optoproteins into a variety of extracellular systems, endowing them with photocontrollability. While other routes exist for dynamically controlling material properties, light-sensitive proteins have several distinct advantages, including precise spatiotemporal control, reversibility, substrate selectivity, as well as biodegradability and biocompatibility. Available conjugation chemistries endow OptoGels with a combinatorially large design space determined by the set of optoproteins and polymer networks. These combinations result in a variety of tunable material properties. Despite their potential, relatively little of the OptoGel design space has been explored. Here, we aim to summarize innovations in this emerging field and highlight potential future applications of these next generation materials. OptoGels show great promise in applications ranging from mechanobiology, to 3D cell and organoid engineering, and programmable cell eluting materials.

An Optogenetic Platform to Dynamically Control the Stiffness of Collagen Hydrogels.

The extracellular matrix (ECM) comprises a meshwork of biomacromolecules whose composition, architecture, and macroscopic properties, such as mechanics, instruct cell fate decisions during development and disease progression. Current methods implemented in mechanotransduction studies either fail to capture real-time mechanical dynamics or utilize synthetic polymers that lack the fibrillar nature of their natural counterparts. Here we present an optogenetic-inspired tool to construct light-responsive ECM mimetic hydrogels comprised exclusively of natural ECM proteins. Optogenetic tools offer seconds temporal resolution and submicron spatial resolution, permitting researchers to probe cell signaling dynamics with unprecedented precision. Here we demonstrated our approach of using SNAP-tag and its thiol-targeted substrate, benzylguanine-maleimide, to covalently attach blue-light-responsive proteins to collagen hydrogels. The resulting material (OptoGel), in addition to encompassing the native biological activity of collagen, stiffens upon exposure to blue light and softens in the dark. Optogels have immediate use in dissecting the cellular response to acute mechanical inputs and may also have applications in next-generation biointerfacing prosthetics.

Correction: Aqueous surface gels as low friction interfaces to mitigate implant-associated inflammation.

Correction for 'Aqueous surface gels as low friction interfaces to mitigate implant-associated inflammation' by Allison L. Chau et al., J. Mater. Chem. B, 2020, 8, 6782-6791, DOI: .

Poroelasticity of highly confined hydrogel films measured with a surface forces apparatus.

The influence of poroelasticity on the contact mechanics of thin polyacrylamide films was investigated with a surface forces apparatus (SFA). A model based on a thin film approximation described compression forces for hydrated gels; polymer scaling theory explained the effects of gel dehydration. The results demonstrate that fluid flow dictates the apparent stiffness of highly confined poroelastic films.

Aqueous surface gels as low friction interfaces to mitigate implant-associated inflammation.

Aqueous surface gels are fragile yet resilient biopolymer-based networks capable of sustaining extremely low friction coefficients despite tribologically-challenging environments. These superficial networks are ubiquitous in natural sliding interfaces and protect mechanosensitive cells from excessive contact pressures and frictional shear stresses from cell-fluid, cell-cell, or cell-solid interactions. Understanding these complex lubrication mechanisms may aid in the development of materials-based strategies for increasing biocompatibility in medical devices and implants. Equally as important is characterizing the interplay between soft and passive yet mobile implant materials and cellular reactions in response to direct contact and frictional shear stresses. Physically interrogating living biological systems without rupturing them in the process is nontrivial. To this end, custom biotribometers have been designed to precisely modulate contact pressures against living human telomerase-immortalized corneal epithelial (hTCEpi) cell layers using soft polyacrylamide membrane probes. Reverse-transcription quantitative polymerase chain-reaction (RT-qPCR) indicated that increased duration and, to a much greater extent, the magnitude of frictional shear stress lead to increased production of pro-inflammatory (IL-1ß, IL-6, MMP9) and pro-apoptotic (DDIT3, FAS) genes, which in clinical studies are linked to pathological pain. The hierarchical structure often found in biological systems has also been investigated through the fabrication of high-water content (polyacrylamide) hydrogels through free-radical polymerization inhibition. Nanoindentation experiments and friction coefficient measurements indicate that these "gradient surface gels" reduce contact pressures and frictional shear stresses at the surface of the material while still maintaining stiffness within the bulk. Reducing frictional shear stresses through informed materials and surface design may concomitantly increase lubricity and quiet the immune response, and thus provide bio-inspired routes to improve patient outcomes and quality of life.

Surface Damage Influences the JKR Contact Mechanics of Glassy Low-Molecular-Weight Polystyrene Films.

Using a surface forces apparatus (SFA), we quantitatively study the influence of surface damage on the contact mechanics of self-mated glassy polystyrene (PS) films. We use the SFA to measure the contact radius, surface profile, and normal force between the films, including the adhesion force. The molecular weight (MW) of the polymer influences the repeatability of the adhesion measurements and the effective surface energy calculated using the Johnson-Kendall-Roberts (JKR) theory. For low-MW PS (MW = 2.33 kDa), the effective surface energy increases over repeated adhesion cycles as the films become progressively damaged. For high-MW PS (MW = 280 kDa), the effective surface energy is constant over repeated adhesion cycles, but hysteresis is still present, manifested in a smaller contact radius during compression of the surfaces than during separation. Our results demonstrate that while the JKR theory is appropriate for describing the contact mechanics of glassy polymer thin films on layered elastic substrates, the contact mechanics of low-MW polymer films can be complicated by surface damage to the films.

Kinetics of aqueous lubrication in the hydrophilic hydrogel Gemini interface.

The exquisite sliding interfaces in the human body share the common feature of hydrated dilute polymer mesh networks. These networks, especially when they constitute a sliding interface such as the pre-corneal tear film on the ocular interface, are described by the molecular weight of the polymer chains and a characteristic size of a minimum structural unit, the mesh size, ξ. In a Gemini interface where hydrophilic hydrogels are slid against each other, the aqueous lubrication behavior has been shown to be a function of sliding velocity, introducing a sliding timescale competing against the time scales of polymer fluctuation and relaxation at the surface. In this work, we examine two recent studies and postulate that when the Gemini interface slips faster than the single-chain relaxation time, chains must relax, suppressing the amplitude of the polymer chain thermal fluctuations.