Synthesis, Characterization and Catechol-Based Bioinspired Adhesive Properties in Wet Medium of Poly(2-Hydroxyethyl Methacrylate-co-Acrylamide) Hydrogels.

Hydrogels consist of crosslinked hydrophilic polymers from which their mechanical properties can be modulated for a wide variety of applications. In the last decade, many catechol-based bioinspired adhesives have been developed following the strategy of incorporating catechol moieties into polymeric backbones. In this work, in order to further investigate the adhesive properties of hydrogels and their potential advantages, several hydrogels based on poly(2-hydroxyethyl methacrylate-co-acrylamide) with N'N-methylene-bisacrylamide (MBA), without/with L-3,4-dihydroxyphenylalanine (DOPA) as a catecholic crosslinker, were prepared via free radical copolymerization. 2-Hydroxyethyl methacrylate (HEMA) and acrylamide (AAm) were used as comonomers and MBA and DOPA both as crosslinking agents at 0.1, 0.3, and 0.5 mol.-%, respectively. The polymeric hydrogels were characterized by Fourier transform infrared spectroscopy (FT-IR), thermal analysis and swelling behavior analysis. Subsequently, the mechanical properties of hydrogels were determined. The elastic properties of the hydrogels were quantified using Young's modulus (stress-strain curves). According to the results herein, the hydrogel with a feed monomer ratio of 1:1 at 0.3 mol.-% of MBA and DOPA displayed the highest rigidity and higher failure shear stress (greater adhesive properties). In addition, the fracture lap shear strength of the biomimetic polymeric hydrogel was eight times higher than the initial one (only containing MBA); however at 0.5 mol.-% MBA/DOPA, it was only two times higher. It is understood that when two polymer surfaces are brought into close contact, physical self-bonding (Van der Waals forces) at the interface may occur in an -OH interaction with wet contacting surfaces. The hydrogels with DOPA provided an enhancement in the flexibility compared to unmodified hydrogels, alongside reduced swelling behavior on the biomimetic hydrogels. This approach expands the possible applications of hydrogels as adhesive materials, in wet conditions, within scaffolds that are commonly used as biomaterials in cartilage tissue engineering.

Design and Study of a Photo-Switchable Polymeric System in the Presence of ZnS Nanoparticles under the Influence of UV Light Irradiation.

Recent progress in the field of photosensitive materials has prompted a need to develop efficient methods to synthesize materials with basic intermolecular architectural designs and novel properties. Accordingly, in this work we design and study a photoactive polymer as a photo-switchable polymeric system in the presence and absence of ZnS nanoparticles (average size < 10 nm) at 5 wt.%. The influence of UV light irradiation on its properties were also studied. The photoactive block copolymer was obtained from styrene (S) and methyl methacrylate (MMA) as monomers and 1-(2-hydroxyethyl)-3,3-dimethylindoline-6-nitrobenzopyran (SP) was grafted to the block copolymer backbone as a photochromic agent. Furthermore, the incorporation of ZnS (NPs) as photo-optical switch component into the system enhances the purple colored photo-emission, with the open form of the spiropyran derivative (merocyanine, MC). The ZnS stabilize the isomeric equilibrium in the MC interconversion of the photochromic agent. The photo-switchable properties of the PS-b-PMMA-SP in the presence of ZnS (NPs) were examined using UV-VIS spectroscopy, Photoluminescence (PL) spectroscopy, optical fluorescence and scanning electronic microscopy (SEM-EDX.). The observed changes in the absorbance, fluorescence and morphology of the system were associated to the reversible interconversion of the two states of the photochromic agent which regulates the radiative deactivation of the luminescent ZnS NPs component. After UV irradiation the photoactive polymer becomes purple in color. Therefore, these basic studies can lead to the development of innovative functional and nanostructured materials with photosensitive character as photosensitive molecular switches.

Exploration of Copper Oxide Nanoneedle Electrosynthesis Applied in the Degradation of Methylene Blue.

In this study, we report a low cost, fast and unexplored electrochemical synthesis strategy of copper oxide nanoneedles films as well as their morphological and chemical characterization. The nanostructured films were prepared using electrochemical anodization in alkaline electrolyte solutions of ethylene glycol, water and fluoride ions. The film morphology shows nanoneedle-shaped structures, with lengths up to 1-2 µm; meanwhile, high-resolution X-ray photoelectron spectroscopy (HRXPS) and spectroscopy Raman analyses indicate that a mixture of Cu(II) and Cu(I) oxides, or only Cu(I) oxide, is obtained as the percentage of water in the electrolyte solution decreases. A preliminary study was also carried out for the photocatalytic degradation of the methylene blue (MB) dye under irradiation with simulated sunlight in the presence of the nanoneedles obtained, presenting a maximum degradation value of 88% of MB and, thus, demonstrating the potential characteristics of the material investigated in the degradation of organic dyes.

Preparation of photoactive ZnS-composite porous polymer films: Fluorescent and morphological properties.

This work describes the use of the breath figure (BF) method for the fabrication of photoactive porous polymer films and the characterization of their responsive to photo stimulus. The films incorporate self-assembled photoactive polymers and ZnS nanoparticles (NPs). The effect of both components on the optical and morphological properties of the films were analyzed. Films with a hexagonally ordered pattern were obtained. The photoactive polymer was prepared by grafting the photochromic component 1-(2-hydroxyethyl)-3,3-dimethylindoline-6-nitrobenzopyran (SP) to polystyrene-block-polymethacrylic acid (PS-b-PMMA). ZnS NPs were incorporated into the polymer solution, and the films were prepared using spin-coating on glass substrates before subjecting them to the BF method. The hollow footprints were obtained before introducing the ZnS NPs in order to maintain the necessary conditions for hexagonal film growth. Accordingly, the SEM micrographs of the films prepared in the presence of ZnS NPs displayed a loss in the pore arrangement as a consequence of the interaction between SP moiety and NPs. The light-emitting properties of films were characterized by blue and violet colors when exposed to UV light under fluorescence. Progress in the field of breath-figure formation and its application, such as exemplified in this work, leads to functional structures with suitable applications in chemistry and materials science. It is expected that such microstructured polymeric films will have interesting applications in photonic and optoelectronic devices.

Electrochemical reduction of Cr(VI) in the presence of sodium alginate and its application in water purification.

Chromium (Cr) is used in many manufacturing processes, and its release into natural waters is a major environmental problem today. Low concentrations of Cr(VI) are toxic to human health and living organisms due to the carcinogenic and mutagenic nature of this mineral. This work examined the conversion of Cr(VI) to Cr(III) via electrochemical reduction using gold electrode in an acidic sodium alginate (SA) solution and subsequent removal of the produced Cr(III)-SA by the polymer-enhanced ultrafiltration (PEUF) technique. A solution of SA in nitric acid was used both as an electrolytic medium during the voltammetric measurements and bulk electrolysis and as an extracting agent during the PEUF technique. The electroanalysis of Cr(VI) was performed by linear sweep voltammetry in the presence of acidic SA solution to study its voltammetric behavior as a function of the Cr(VI) concentration, pH, presence of Cr(III), SA concentration and scan rate. In addition, the quantitative reduction of Cr(VI) to Cr(III) was studied through the bulk electrolysis technique. The results showed efficient reduction with well-defined peaks at approximately 0.3 V vs. Ag/AgCl, using a gold working electrode. As the pH increased, the reduction signal strongly decreased until its disappearance. The optimum SA concentration was 10 mmol/L, and it was observed that the presence of Cr(III) did not interfere in the Cr(VI) electroanalysis. Through the quantitative reduction by bulk electrolysis in the presence of acidic SA solution, it was possible to reduce all Cr(VI) to Cr(III) followed by its removal via PEUF.

In Vitro Hyperthermia Evaluation of Electrospun Polymer Composite Fibers Loaded with Reduced Graphene Oxide.

Electrospun meshes (EM) composed of natural and synthetic polymers with randomly or aligned fibers orientations containing 0.5% or 1% of thermally reduced graphene oxide (TrGO) were prepared by electrospinning (ES), and their hyperthermia properties were evaluated. EM loaded with and without TrGO were irradiated using near infrared radiation (NIR) at 808 nm by varying the distance and electric potential recorded at 30 s. Morphological, spectroscopic, and thermal aspects of EM samples were analyzed by using SEM-EDS, Raman and X-ray photoelectron (XPS) spectroscopies, X-ray diffraction (XRD), and NIR radiation response. We found that the composite EM made of polyvinyl alcohol (PVA), natural rubber (NR), and arabic gum (AG) containing TrGO showed improved hyperthermia properties compared to EM without TrGO, reaching an average temperature range of 42-52 °C. We also found that the distribution of TrGO in the EM depends on the orientation of the fibers. These results allow infering that EM loaded with TrGO as a NIR-active thermal inducer could be an excellent candidate for hyperthermia applications in photothermal therapy.

Porous Surface Films With Tunable Morphologies and Hydrophobic Properties Based on Block Copolymer Under the Effects of Thermal Annealing.

The fabrication of porous-structured polymer films with patterned surface structures has recently attracted increased interest within the material science field. In this work, a series of microstructure scale patterned polymer films were obtained via breath figure methods (BF) with hydrophobic surface films based on self-assembled diblock copolymers by atom-transfer radical polymerization (ATRP). The surface characteristics and morphological properties, pore size, roughness, thickness, and wettability of the block copolymer films was studied in response to variation of the hydrophilic co-monomer structures. A significant improvement of the quality and order of the hydrophobic films was observed in response to thermal annealing and a consequent optimization of the assembly process.

In-Situ Preparation of CdTe Quantum Dots Capped with a ß-Cyclodextrin-Epichlorohydrin Polymer: Polymer Influence on the Nanocrystal's Optical Properties.

ß-Cyclodextrin (ßCD), the less water soluble of the cyclodextrins, has been used as a capping agent in the preparation of semiconductor nanocrystals or quantum dots (QDs). Nevertheless, no reports have been found in the use of the highly water-soluble polymer of this, prepared by the crosslinking of the ßCD units with epichlorohydrin in basic medium (ßCDP). This polymer, besides to overcome the low solubility of the ßCD, increases the inclusion constant of the guest; two parameters that deserve its use as capping agent, instead of the native cyclodextrin. In the present manuscript, we afforded the in-situ aqueous preparation of cadmium telluride (CdTe) QDs capped with ßCDP. The polymer influence on the photoluminescent properties of the nanocrystals was analyzed. The ßCDP controls the nanocrystals growth during the Oswald ripening stage. Consequently, the CdTe capped ßCDP QDs showed lower Stokes-shift values, higher photoluminescent efficiency, and narrower size distribution than for nanocrystals obtained in the absence of polymer. Transmission electron microscopy (TEM) micrographs and energy dispersive X-ray spectroscopy (EDS) analysis revealed the composition and crystallinity of the CdTe QDs. This ßCDP capped CdTe QDs is a potential scaffold for the supramolecular modification of QDs surface.

Comparative study of the self-aggregation of rhodamine 6G in the presence of poly(sodium 4-styrenesulfonate), poly(N-phenylmaleimide-co-acrylic acid), poly(styrene-alt-maleic acid), and poly(sodium acrylate).

The interaction between rhodamine 6G and different polyelectrolytes is analyzed. Structural aspects differentiate these polyelectrolytes, such as the presence of aromatic groups and the number and localization of their respective charges, which may be directly attached to the aromatic groups or to the polymeric main chain. In the case of poly(sodium acrylate), which does not bear aromatic groups, the polyelectrolyte induces cooperative self-stacking between the dyes which is highly sensitive to the ionic strength, due to the predominance of long-range electrostatic interactions between the polymer and the dye. In the case of poly(sodium 4-styrenesulfonate), whose charge is directly attached to the aromatic groups, a high dispersant ability of the dyes is found and the interaction is less dependent on the ionic strength, due to the predominance of short-range aromatic-aromatic interactions between the dye and the polymer. Among the two polyelectrolytes studied for which the polymeric charge is directly attached to the main chain, and separated from the aromatic group, poly(styrene-alt-maleic acid) shows a lower dependence of the interaction on the ionic strength than poly(N-phenylmaleimide-co-acrylic acid) at a comonomer composition of 1:2, due to a higher linear aromatic density and a lower linear charge density, indicating the importance of hydrophobic forces. Both copolymers exhibit a high ability to induce cooperative self-aggregation of the dye.

Polyaromatic-anion behavior of different polyelectrolytes containing benzenecarboxylate units.

The polyaromatic-ion behavior of poly(sodium N-maleoyl-2-aminobenzoate-co-sodium acrylate) in a comonomer composition 1:2, poly(sodium N-maleoyl-4-aminobenzoate-co-sodium acrylate) in a comonomer composition 1:2, and poly(sodium N-maleoyl-4-aminobenzoate-co-N,N-dimethylacrylamide) in a comonomer composition 1:1 is studied. The copolymers undergo short-range aromatic-aromatic interactions with methylene blue and rhodamine B, as a consequence of which their UV-vis monomer band is shifted to lower energies. As a result of their polyaromatic-anion behavior, methylene blue is easily dispersed on the polymeric domains. Moreover, the pK(a) of rhodamine B is shifted from 3.2 to 4.5-5 in the presence of these copolymers. This behavior is also observed in the presence poly(sodium 4-styrenesulfonate), but not in the presence of poly(sodium vinyl sulfonate), which are taken as reference polymers. Compared with poly(sodium 4-styrenesulfonate), a lower resistance to the cleaving effect of added NaCl on the interaction with methylene blue is found. A different influence on the reduction of 2,3,5-triphenyl-2H-tetrazolium chloride with ascorbic acid was found for the different polyelectrolytes.