Pilot Test on Pre-Swim Hygiene as a Factor Limiting Trihalomethane Precursors in Pool Water by Reducing Organic Matter in an Operational Facility.

Pool water must be constantly disinfected. Chlorine compounds used to disinfect pools react with organic substances such as sweat, urine, and personal care products introduced into pool water by users and results in the formation of disinfection byproducts. Trihalomethanes (THM), including chloroform and dissolved organic carbon (DOC) concentrations, were quantified using a two-stage process: determining initial THM and chloroform levels; then searching for a cheap and easy-to-use method to improve water quality. The method proposed here to limit THM and DOC concentrations in water is controlled showering. At three swimming pool facilities, chloroform concentrations (13.8 ± 0.33 µg/L, 15.5 ± 0.44 µg/L, and 13.9 ± 0.06 µg/L) were below the threshold concentration of 30 µg/L. At a fourth facility, however, the chloroform concentration exceeded that threshold (40.7 ± 9.68 µg/L) when showering was not controlled. Those conditions improved after the introduction of a mandatory shower; concentrations of DOC, THMs, and chloroform all decreased. The chloroform concentration decreased to 29.4 ± 3.8 µg/L, the THM concentration was 31.3 ± 3.9 µg/L, and the DOC concentration was 6.09 ± 0.05 mg/L. Pilot tests were carried out at real facilities to determine whether the control of pre-swim hygiene was possible. The introduction of proper pre-swim hygiene limited the concentration of DOC in water and can lead to a healthier environment for everyone attending the swimming facility.

Analysis of the Kinetics of Swimming Pool Water Reaction in Analytical Device Reproducing Its Circulation on a Small Scale.

The most common cause of diseases in swimming pools is the lack of sanitary control of water quality; water may contain microbiological and chemical contaminants. Among the people most at risk of infection are children, pregnant women, and immunocompromised people. The origin of the problem is a need to develop a system that can predict the formation of chlorine water disinfection by-products, such as trihalomethanes (THMs). THMs are volatile organic compounds from the group of alkyl halides, carcinogenic, mutagenic, teratogenic, and bioaccumulating. Long-term exposure, even to low concentrations of THM in water and air, may result in damage to the liver, kidneys, thyroid gland, or nervous system. This article focuses on analysis of the kinetics of swimming pool water reaction in analytical device reproducing its circulation on a small scale. The designed and constructed analytical device is based on the SIMATIC S7-1200 PLC driver of SIEMENS Company. The HMI KPT panel of SIEMENS Company enables monitoring the process and control individual elements of device. Value of the reaction rate constant of free chlorine decomposition gives us qualitative information about water quality, it is also strictly connected to the kinetics of the reaction. Based on the experiment results, the value of reaction rate constant was determined as a linear change of the natural logarithm of free chlorine concentration over time. The experimental value of activation energy based on the directional coefficient is equal to 76.0 [kJ×mol-1]. These results indicate that changing water temperature does not cause any changes in the reaction rate, while it still affects the value of the reaction rate constant. Using the analytical device, it is possible to constantly monitor the values of reaction rate constant and activation energy, which can be used to develop a new way to assess pool water quality.

Correction to "Physicochemical Properties of Terebic Acid, MBTCA, Diaterpenylic Acid Acetate, and Pinanediol as Relevant α-Pinene Oxidation Products".

[This corrects the article DOI: 10.1021/acsomega.9b04231.].

Physicochemical Properties of Terebic Acid, MBTCA, Diaterpenylic Acid Acetate, and Pinanediol as Relevant α-Pinene Oxidation Products.

The physicochemical properties and the synthesis of four α-pinene oxidation products, terebic acid, 3-methyl-1,2,3-butanetricarboxylic acid (MBTCA), diaterpenylic acid acetate (DTAA), and pinanediol, are presented in this study. The physicochemical properties encompass thermal properties, solubility in water, and dissociation constant (pK a) for the investigated compounds. It was found that terebic acid exhibits a relatively high melting temperature of 449.29 K, whereas pinanediol revealed a low melting temperature of 329.26 K. The solubility in water was determined with the dynamic method and the experimental results were correlated using three different mathematical models: Wilson, NRTL, and UNIQUAC equations. The results of the correlation indicate that the Wilson equation appears to work the best for terebic acid and pinanediol. The calculated standard deviation was for 3.79 for terebic acid and 1.25 for pinanediol. In contrast, UNIQUAC was the best mathematical model for DTAA and MBTCA. The calculated standard deviation was 0.57 for DTAA and 2.21 for MBTCA. The measured water solubility increased in the following order: pinanediol > DTAA ≥ MBTCA > terebic acid, which affects their multiphase aging chemistry in the atmosphere. Moreover, acidity constants (pK a) at 298, 303, and 308 K were determined for DTAA with the Bates-Schwarzenbach spectrophotometric method. The pK a values obtained at 298, 303, and 308 K were found to be 3.76, 3.85, and 3.88, respectively.

Physicochemical Properties of Pinic, Pinonic, Norpinic, and Norpinonic Acids as Relevant α-Pinene Oxidation Products.

Here, the study is focused on the synthesis and determination of physicochemical properties of four α-pinene secondary organic aerosol (SOA) products: cis-pinic acid, cis-pinonic acid, cis-norpinic acid, and cis-norpinonic acid. These encompass their thermal properties, solid-liquid phase equilibria, and dissociation constant (pKa). Thermal properties, including the melting temperature, enthalpy of fusion, temperature, and enthalpy of the phase transitions, were measured with the differential scanning calorimetry technique. These SOA components exhibit relatively high melting temperatures from 364.32 K for cis-pinic acid to 440.68 K for cis-norpinic acid. The enthalpies of fusion vary from 14.75 kJ·mol-1 for cis-norpinic acid to 30.35 kJ·mol-1 for cis-pinonic acid. The solubility in water was determined with the dynamic method (solid-liquid phase equilibria method), and then experimental results were interpreted and correlated using three different mathematical models: Wilson, non-random two-liquid model, and universal quasichemical equations. The results of the correlation indicate that the Wilson equation appears to work the best for all investigated compounds, giving rise to the lowest value of a standard deviation. cis-Norpinic acid and cis-pinic acid (dicarboxylic acids) show better solubility in the aqueous solution than cis-norpinonic acid and cis-pinonic acid (monocarboxylic acids), which affect the multiphase chemistry of α-pinene SOA processes. For cis-pinonic acid and cis-norpinonic acid, also pH-profile solubility was determined. The intrinsic solubility (S0) for cis-norpinonic acid was measured to be 0.05 mmol·dm-3, while for cis-pinonic acid, it was found to be 0.043 mmol·dm-3. The acidity constants (pKa) at 298 and 310 K using the Bates-Schwarzenbach spectrophotometric method were determined. The pKa values at 298.15 K for cis-norpinonic acid and cis-pinonic acid were found to be 4.56 and 5.19, respectively, whereas at 310.15 K, pKa values were found to be -4.76 and 5.25, respectively.

Studying of drug solubility in water and alcohols using drug-ammonium ionic liquid-compounds.

Synthesis of three mefenamic acid (MEF) derivatives - ionic liquid compounds composed of MEF in an anionic form and ammonium cation (choline, MEF1), or {di(2-hydroxyethyl)dimethyl ammonium (MEF2)}, or {tri(2-hydroxyethyl)methyl ammonium compound (MEF3)} is presented. The basic thermal properties of pure compounds i.e. fusion temperatures, and the enthalpy of fusion of these compounds have been measured with differential scanning microcalorimetry technique (DSC). Molar volumes have been calculated with the Barton group contribution method. The solubilities of MEF1, MEF2 and MEF3 using the dynamic method were measured at constant pH in a range of temperature from (290 to 370) K in three solvents: water, ethanol and 1-octanol. The experimental solubility data have been correlated by means of three commonly known GE equations: the Wilson, NRTL and UNIQUAC with the assumption that the systems studied here present simple eutectic behaviour. The activity coefficients of pharmaceuticals at saturated solutions in each binary mixture were calculated from the experimental data. The formation of MEF-ionic liquid compounds greatly increases the solubility in water in comparison with pure MEF or complexes with 2-hydroxypropyl-ß-cyclodextrin. The development of these compounds formulations will assist in medication taking into account oral solid or gel medicines.

Phenothiazines solution complexity - Determination of pKa and solubility-pH profiles exhibiting sub-micellar aggregation at 25 and 37°C.

The ionization constants (pKa) and the pH-dependent solubility (log S-pH) of six phenothiazine derivatives (promazine hydrochloride, chlorpromazine hydrochloride, triflupromazine hydrochloride, fluphenazine dihydrochloride, perphenazine free base, and trifluoperazine dihydrochloride) were determined at 25 and 37°C. The pKa values of these low-soluble surface active molecules were determined by the cosolvent method (n-propanol/water at 37°C and methanol/water at 25°C). The log S-pH profiles were measured at 24h incubation time in 0.15M phosphate buffers. The log S-pH "shape-template" method, which critically depends on accurate pKa values (determined independently of solubility data), was used to propose speciation models, which were subsequently refined by rigorous mass-action weighted regression procedure described recently. Differential scanning calorimetry (DSC), UV-visible spectrophotometry, potentiometric, and high performance liquid chromatography (HPLC) measurements were used to characterize the compounds. The intrinsic solubility (S0) values of the three least-soluble drugs (chlorpromazine·HCl, triflupromazine·HCl, and trifluoperazine·2HCl) at 25°C were 0.5, 1.1, and 2.7µg/mL (resp.). These values increased to 5.5, 9.2, and 8.7µg/mL (resp.) at the physiological temperature. The enthalpies of solution for the latter compounds were exceptionally high positive (endothermic) values (99-152kJ·mol(-1)). Cationic sub-micellar aggregates were evident (from the distortions in the log S-pH profiles) for chlorpromazine, fluphenazine, perphenazine, and trifluoperazine at 25°C. The effects persisted at 37°C for chlorpromazine and trifluoperazine. The solids in suspension were apparently amorphous in cases where the drugs were introduced as the chloride salts.

Solubility and pKa determination of six structurally related phenothiazines.

Solubilities of six structurally related phenothiazines, namely chlorpromazine hydrochloride, fluphenazine dihydrochloride, promazine hydrochloride, thioridazine hydrochloride, trifluoperazine dihydrochloride, and triflupromazine hydrochloride at constant pH were measured in the temperature range from 290 K to 350 K in three important drugs solvents: water, ethanol and 1-octanol using the dynamic method and UV-vis method. Dissociation constants and corresponding pK(a) values of drugs were obtained with Bates-Schwarzenbach method at temperature 298.15K in the buffer solutions. Our experimental pK(a) values for chlorpromazine hydrochloride, fluphenazine dihydrochloride, promazine hydrochloride, thioridazine hydrochloride, trifluoperazine dihydrochloride, and triflupromazine hydrochloride are 9.15, 10.01, 9.37, 8.89, 8.97, and 9.03, respectively. The basic thermal properties of pure drugs i.e. melting and solid-solid phase transition as well as glass-transition temperatures, the enthalpy of melting and phase transitions and the molar heat capacity at glass transition (at constant pressure) were measured with differential scanning microcalorimetry (DSC) technique. Molar volumes were calculated with Barton group contribution method. The experimental solubility data were correlated by means of three commonly known G(E) equations: the Wilson, NRTL and UNIQUAC with the assumption that the systems studied here have revealed simple eutectic mixtures. The root-mean-square deviations of temperature were used for the precision of the correlation. The activity coefficients of drugs at saturated solutions in each correlated binary mixture were calculated from the experimental data. These new data will help in all prediction-methods and their precision.

Effect of 2-hydroxypropyl-ß-cyclodextrin on solubility of sparingly soluble drug derivatives of anthranilic acid.

Guest-host complex formation of three drug derivatives of anthranilic acid, mefenamic acid, niflumic acid, and flufenamic acid with 2-hydroxypropyl-ß-cyclodextrin (2HP-ß-CD) in aqueous solutions was investigated using "Phase solubility study" with UV-vis spectrophotometry. Solubility of sparingly soluble drugs has been improved by addition of 2HP-ß-CD at two temperatures 298.15 K and 310.15 K and two pH values 2 and 7. The influence of different 2HP-ß-CD concentration on solubility of drugs at different pH and temperatures has been investigated. The 2HP-ß-CD-drug complex stability constants (K(s)), and dissociations constants (K(d)), as well as the thermodynamic parameters of reaction, i.e., the free energy change (ΔG), the enthalpy change (ΔH) and the entropy change (ΔS), were determined. The experimental data indicated formation of 1:1 inclusion complexes, which were found effective binders increasing the solubility of drugs.

Solubility of sparingly soluble drug derivatives of anthranilic acid.

This work is a continuation of our systematic study of the solubility of pharmaceuticals (Pharms). All substances here are derivatives of anthranilic acid, and have an anti-inflammatory direction of action (niflumic acid, flufenamic acid, and diclofenac sodium). The basic thermal properties of pure Pharms, i.e., melting and glass-transition temperatures as well as the enthalpy of melting, have been measured with the differential scanning microcalorimetry technique (DSC). Molar volumes have been calculated with the Barton group contribution method. The equilibrium mole fraction solubilities of three pharmaceuticals were measured in a range of temperatures from 285 to 355 K in three important solvents for Pharm investigations: water, ethanol, and 1-octanol using a dynamic method and spectroscopic UV-vis method. The experimental solubility data have been correlated by means of the commonly known G(E) equation: the NRTL, with the assumption that the systems studied here have revealed simple eutectic mixtures. pK(a) precise measurement values have been investigated with the Bates-Schwarzenbach spectrophotometric method.

Modelling, solubility and pK(a) of five sparingly soluble drugs.

Drug solubility is an important aspect of drug development. The objective of this investigation was to measure solubilities of five drugs (cimetidine, phenylbutazone, fenbufen, nitrofurantoin, triamterene) at constant pH in range of temperature from 270 to 340K in three solvents: water, ethanol and 1-octanol with the dynamic-visual method and the saturation shake-flask method using spectrophotometric analysis. The Barton group contribution method was used for the calculations of molar volumes of solutes. The thermodynamic description of the solubility curves was made using the thermophysical properties obtained with the differential scanning microcalorimetry technique (DSC). The DSC measurements have shown different than existing in the literature enthalpies of melting for phenylbutazone and fenbufen. The experimental solubility data also differ from the literature data, normally measured at one, or two temperatures only. The solubility data have been correlated by means of three commonly known excess Gibbs energy, G(E) equations. The activity coefficients of drugs at saturated solutions were calculated from the experimental data. Reexamination of the pK(a) values using diluted solutions was made with the Bates-Schwarzenbach method for the pK(a) measurements. The association constants and corresponding pK(a) values of drugs were close to the most of the literature data. We hope that our new solubility data, thermophysical data, and pK(a) values will improve all prediction-methods and their precision.

pKa and solubility of drugs in water, ethanol, and 1-octanol.

Dissociation constants and corresponding pK(a) values of five drugs were obtained with the Bates-Schwarzenbach method using a Perkin-Elmer Lambda 35 UV/vis spectrophotometer at temperature 298.15 K in the buffer solutions. Atropine, promethazine hydrochloride, ibuprofen, flurbiprofen, and meclofenamic acid sodium salt exhibited pK(a) values of 10.3, 6.47, 5.38, 4.50, and 4.39, respectively. The equilibrium mole fraction solubilities of six drugs were measured in a range of temperatures from 240 to 340 K in three important solvents for drugs: water, ethanol, and 1-octanol using the dynamic method. The basic thermal properties of pure drugs, i.e., melting and glass-transition temperatures, as well as the enthalpy of melting and the molar heat capacity at glass transition (at constant pressure) have been measured with the differential scanning microcalorimetry technique (DSC). Molar volumes have been calculated with the Barton group contribution method. The experimental solubility data have been correlated by means of three commonly known G(E) equations: the Wilson, NRTL, and UNIQUAC, with the assumption that the systems studied here have revealed simple eutectic mixtures. As a measure of goodness of correlation, the root-mean-square deviations of temperature have been used. The activity coefficients of the drugs in saturated solutions for each correlated binary mixture were calculated from the experimental data.

Phase equilibria study of the binary systems (1-butyl-3-methylimidazolium thiocyanate ionic liquid + organic solvent or water).

(Solid + liquid) phase equilibria (SLE) for the binary systems, ionic liquid (IL) 1-butyl-3-methylimidazolium thiocyanate [BMIM][SCN] with an alcohol (1-octanol, 1-nonanol, 1-decanol, 1-undecanol, or 1-dodecanol) or water, and (liquid + liquid) phase equilibria (LLE) for the binary systems of [BMIM][SCN] with an alkane (n-hexane, n-heptane, n-octane, n-nonane, or n-decane), benzene, an alkylbenzenes (toluene or ethylbenzene), tetrahydrofuran (THF), cycloalkanes (cyclohexane or cycloheptane), or ethers (di-n-propyl ether, di-n-butyl ether, di-n-pentyl ether, n-butylmethyl ether, tert-butylmethyl ether (MTBE), or tert-butylethyl ether (ETBE)) have been determined at ambient pressure. A dynamic method was used over a broad range of mole fractions and temperatures from 250 to 430 K. In the case of systems IL + alkane, cycloalkane, or ether, the mutual immiscibility with an upper critical solution temperature (UCST) was detected, and in the systems of IL + benzene, alkylbenzene, or THF, the mutual immiscibility with a lower critical solution temperature (LCST) was observed. UV-vis spectroscopy was used to determine the very small compositions of the IL in the n-hexane (about 2 x 10(-5) IL mole fraction), benzene (about 2 x 10(-3) IL mole fraction), cyclohexane (about 2 x 10(-5) IL mole fraction), and THF (about 1.2 x 10(-2) IL mole fraction). For the binary systems containing alcohol, it was noticed that with increasing chain length of an alcohol, the solubility decreases. The basic thermal properties of the pure IL, that is, the glass-transition temperature as well as the heat capacity at the glass-transition temperature, have been measured using a differential scanning microcalorimetry technique (DSC). Decomposition of the IL was detected by the simultaneous TG/DTA experiments. Well-known UNIQUAC, Wilson, and NRTL equations have been used to correlate the experimental SLE data sets for alcohols and water. For the systems containing immiscibility gaps {IL + alkane, benzene, alkylbenzene, cycloalkane, tetrahydrofuran, or ether}, the parameters of the LLE correlation have been derived using the NRTL equation.

Surface tension of binary mixtures of imidazolium and ammonium based ionic liquids with alcohols, or water: cation, anion effect.

The surface tensions were measured at atmospheric pressure, with use of a ring tensiometer, of a series of alcoholic solutions of closely related ionic liquids: 1-methyl-3-methylimidazolium methylsulfate, [MMIM][CH3SO4] in alcohol (methanol, or ethanol, or 1-butanol at 298.15 K), 1-butyl-3-methylimidazolium methylsulfate, [BMIM][CH3SO4] in alcohol (methanol, or ethanol, or 1-butanol at 298.15 K), 1-butyl-3-methylimidazolium octylsulfate, [BMIM][OcSO4] in alcohol (methanol, or 1-butanol at 298.15 K) and of 1-hexyloxymethyl-3-methylimidazolium tetrafluoroborate, [C6H(13)OCH2MIM][BF4], 1,3-dihexyloxymethylimidazolium tetrafluoroborate, [(C6H13OCH2)2IM][BF4] in alcohol (methanol, or 1-butanol, or 1-hexanol at 308.15 and 318.5 K) and hexyl(2-hydroxyethyl)dimethylammonium bromide, C6Br in 1-octanol at 298.15 K. The set of ammonium ionic liquids of different cations and anions (C2Br, C2BF4, C2PF6, C2N(CN)2, C3Br, C4Br and C6Br) was chosen to show the influence of small amount of the ammonium ionic liquid on the surface tension of water at 298.15 K. The influence of the cation, or anion alkyl chain length on the properties under study (densities and surface tension) was tested.