Thermo-elastic gigahertz-frequency oscillator through surface acoustic wave-silicon photonics.

Opto-electronic oscillators are sources of microwave-frequency tones that may reach very low noise levels. Much effort is being dedicated to the realization of oscillators based on photonic integrated devices. In this work, we propose and demonstrate a thermo-elastic opto-electronic oscillator at 2.213 GHz frequency based on a standard silicon-photonic integrated circuit. A microwave-frequency electrical signal modulates an optical pump wave carrier. The modulated waveform launches surface acoustic waves in a silicon-on-insulator substrate, through absorption in a metallic grating and thermo-elastic actuation. The waveform is reconverted to the optical domain through photoelastic modulation of an optical probe wave carrier in a standard racetrack resonator waveguide. Both the thermo-elastic actuation and the photoelastic modulation are radio-frequency selective. The output probe wave is detected, and the receiver voltage is amplified and fed back to modulate the optical pump input. Sufficient gain drives the loop into oscillations. The oscillator does not involve piezoelectricity and can be realized on any substrate. Long acoustic delays may be implemented in compact devices. The frequency of operation is scalable to tens of GHz. The principle may be useful in integrated microwave-photonic signal processing and in the elastic analysis of surfaces and thin layers.

Analysis of thin layers using surface acoustic wave-photonic devices in silicon-on-insulator.

The analysis of thin layers deposited on various substrates is widely employed in thickness monitoring, materials research and development and quality control. Measurements are often performed based on changes to acoustic resonance frequencies of quartz micro-balance devices. The technique is extremely sensitive, but it is restricted to hundreds of MHz frequencies and requires electrical connectivity. In this work we propose and demonstrate the analysis of elastic properties of thin layers deposited on surface acoustic wave-photonic devices in standard silicon-on-insulator. The devices operate at 2.4 GHz frequency, and their interfaces are fiber-optic. The radio-frequency transfer functions of the devices are modified by sub-percent level changes to the group velocity of surface acoustic waves following deposition of layers. Layers of aluminum oxide and germanium sulfide of thickness between 10-80 nm are characterized. The analysis provides estimates for Young's modulus of the layers.

Surface acoustic wave photonic devices in silicon on insulator.

Opto-mechanical interactions in planar photonic integrated circuits draw great interest in basic research and applications. However, opto-mechanics is practically absent in the most technologically significant photonics platform: silicon on insulator. Previous demonstrations required the under-etching and suspension of silicon structures. Here we present surface acoustic wave-photonic devices in silicon on insulator, up to 8 GHz frequency. Surface waves are launched through absorption of modulated pump light in metallic gratings and thermo-elastic expansion. The surface waves are detected through photo-elastic modulation of an optical probe in standard race-track resonators. Devices do not involve piezo-electric actuation, suspension of waveguides or hybrid material integration. Wavelength conversion of incident microwave signals and acoustic true time delays up to 40 ns are demonstrated on-chip. Lastly, discrete-time microwave-photonic filters with up to six taps and 20 MHz-wide passbands are realized using acoustic delays. The concept is suitable for integrated microwave-photonics signal processing.

Process-Function Data Mining for the Discovery of Solid-State Iron-Oxide PV.

Data mining tools have been known to be useful for analyzing large material data sets generated by high-throughput methods. Typically, the descriptors used for the analysis are structural descriptors, which can be difficult to obtain and to tune according to the results of the analysis. In this Research Article, we show the use of deposition process parameters as descriptors for analysis of a photovoltaics data set. To create a data set, solar cell libraries were fabricated using iron oxide as the absorber layer deposited using different deposition parameters, and the photovoltaic performance was measured. The data was then used to build models using genetic programing and stepwise regression. These models showed which deposition parameters should be used to get photovoltaic cells with higher performance. The iron oxide library fabricated based on the model predictions showed a higher performance than any of the previous libraries, which demonstrates that deposition process parameters can be used to model photovoltaic performance and lead to higher performing cells. This is a promising technique toward using data mining tools for discovery and fabrication of high performance photovoltaic materials.

Smartphone-based hearing test as an aid in the initial evaluation of unilateral sudden sensorineural hearing loss.

Sudden sensorineural hearing loss (SSNHL) can cause significant morbidity. Treatment with steroids can improve outcome. Delay in initiation of treatment reduces the chance to regain hearing. For this reason SSNHL is considered an emergency. Diagnosis is based on history, physical examination and a standard audiogram, the latter requiring specialized equipment and personnel. Standard audiogram may not be available at the time and place of patient presentation. A smartphone or tablet computer-based hearing test may aid in the decision to prescribe steroids in this setting. In this study the uHear™ hearing test application was utilized. The output of this ear-level air conduction hearing test is reported in hearing grades for 6 frequencies ranging from 250 to 6000 Hz. A total of 32 patients with unilateral SSNHL proven by a standard audiogram were tested. The results of standard and iPod hearing tests were compared. Based on the accepted criterion of SSNHL (at least 30 dB loss - or 2 hearing grades - in 3 consecutive frequencies) the test had a sensitivity of 0.76 and specificity of 0.91. Using a less stringent criterion of a loss of 2 hearing grades over at least 2 frequencies the sensitivity was 0.96 and specificity 0.86. The correlation coefficient for the comparison of the average hearing grade across the 6 measured frequencies of the study and standard audiogram was 0.83. uHear more accurately reflected hearing thresholds at mid and high tones. Similarly to previously published data, low frequency thresholds could be artificially elevated. In conclusion, uHear can be useful in the initial evaluation of patients with single-sided SSNHL by providing important information guiding the decision to initiate treatment before a standard audiogram is available.