The Influence of Environmental Factors on the Degradation of PLA/Diatomaceous Earth Composites.

In the present study, tests were carried out on composite samples on a polylactide matrix containing 25% by weight of mineral filler in the form of diatomaceous earth, base, and silanized with GPTMOS (3-glycidoxypropyltrimethoxysilane), OTES (n-octyltriethoxysilane), and MTMOS (methyltrimethoxysilane) silanes. The addition of two types of waxes, synthetic polyamide wax and natural beeswax, were used as a factor to increase the rheological properties of the composites. The obtained samples were characterized in terms of the effect of filler silanization on the degradation rate of the composites. The tests were conducted under different conditioning conditions, i.e., after exposure to strong UV radiation for 250 and 500 h, and under natural sunlight for 21 days. The conditioning carried out under natural conditions showed that the modified samples exhibit up to twice the degradation rate of pure polylactide. The addition of synthetic wax to the composites increases the tendency to agglomerate diatomaceous earth, while natural wax has a positive effect on filler dispersion. For composites modified with GPTMOS and OTES silanes, it was noted that the addition of natural wax inhibited the degree of surface degradation, compared to the addition of synthetic wax, while the addition of MTMOS silane caused the opposite effect and samples with natural wax degraded more strongly. It was shown that, despite the high degree of surface degradation, the process does not occur significantly deep into the composite and stops at a certain depth.

Enhancing the Thermal Resistance of UV-Curable Resin Using (3-Thiopropyl)polysilsesquioxane.

This study delineates a methodology for the preparation of new composites based on a photocurable urethane-acrylate resin, which has been modified with (3-thiopropyl)polysilsesquioxane (SSQ-SH). The organosilicon compound combines fully enclosed cage structures and incompletely condensed silanols (a mixture of random structures) obtained through the hydrolytic condensation of (3-mercaptopropyl)trimethoxysilane. This process involves a thiol-ene "click" reaction between SSQ-SH and a commercially available resin (Ebecryl 1271®) in the presence of the photoinitiator DMPA, resulting in composites with significantly changed thermal properties. Various tests were conducted, including thermogravimetric analysis (TGA), Fourier transmittance infrared spectroscopy (FT-IR), differential scanning calorimetry (Photo-DSC), and photoreological measurement mechanical property, and water contact angle (WCA) tests. The modification of resin with SSQ-SH increased the temperature of 1% and 5% mass loss compared to the reference (for 50 wt% SSQ-SH, T5% was 310.8 °C, an increase of 20.4 °C). A composition containing 50 wt% of SSQ-SH crosslinked faster than the reference resin, a phenomenon confirmed by photorheological tests. This research highlights the potential of new composite materials in coating applications across diverse industries. The modification of resin with SSQ-SH not only enhances thermal properties but also introduces a host of functional improvements, thereby elevating the performance of the resulting coatings.

OH End-Capped Silicone as an Effective Nucleating Agent for Polylactide-A Robotizing Method for Evaluating the Mechanical Characteristics of PLA/Silicone Blends.

Current research on materials engineering focuses mainly on bio-based materials. One of the most frequently studied materials in this group is polylactide (PLA), which is a polymer derived from starch. PLA does not have a negative impact on the natural environment and additionally, it possesses properties comparable to those of industrial polymers. The aim of the work was to investigate the potential of organosilicon compounds as modifiers of the mechanical and rheological properties of PLA, as well as to develop a new method for conducting mechanical property tests through innovative high-throughput technologies. Precise dosing methods were utilized to create PLA/silicone polymer blends with varying mass contents, allowing for continuous characterization of the produced blends. To automate bending tests and achieve comprehensive characterization of the blends, a self-created workstation setup has been used. The tensile properties of selected blend compositions were tested, and their ability to withstand dynamic loads was studied. The blends were characterized through various methods, including rheological (MFI), X-ray (XRD), spectroscopic (FTIR), and thermal properties analysis (TG, DSC, HDT), and they were evaluated using microscopic methods (MO, SEM) to examine their structures.

Preparation and Characterization of Composites Based on ABS Modified with Polysiloxane Derivatives.

In this study, organosilicon compounds were used as modifiers of filaments constituting building materials for 3D printing technology. Polymethylhydrosiloxane underwent a hydrosilylation reaction with styrene, octadecene, and vinyltrimethoxysilane to produce new di- or tri-functional derivatives with varying ratios of olefins. These compounds were then mixed with silica and incorporated into the ABS matrix using standard processing methods. The resulting systems exhibited changes in their physicochemical and mechanical characteristics. Several of the obtained composites (e.g., modified with VT:6STYR) had an increase in the contact angle of over 20° resulting in a hydrophobic surface. The addition of modifiers also prevented a decrease in rheological parameters regardless of the amount of filler added. In addition, comprehensive tests of the thermal decomposition of the obtained composites were performed and an attempt was made to precisely characterize the decomposition of ABS using FT-IR and optical microscopy, which allowed us to determine the impact of individual groups on the thermal stability of the system.

Robotization of Three-Point Bending Mechanical Tests Using PLA/TPU Blends as an Example in the 0-100% Range.

This article presents the development of an automated three-point bending testing system using a robot to increase the efficiency and precision of measurements for PLA/TPU polymer blends as implementation high-throughput measurement methods. The system operates continuously and characterizes the flexural properties of PLA/TPU blends with varying TPU concentrations. This study aimed to determine the effect of TPU concentration on the strength and flexural stiffness, surface properties (WCA), thermal properties (TGA, DSC), and microscopic characterization of the studied blends.

New Ethynylphenylborasilsesquioxanes-Their Reactivity and Behavior during Thermal Decomposition.

In this paper, a new type of borasilsesquioxanes was synthesized through a condensation process, and its reactivity in catalytic hydrosilylation reactions with silanes, siloxanes, and silsesquioxanes was investigated. The obtained compounds were mostly obtained in >90% yield. They were fully characterized using spectroscopic (1H, 13C, 29Si NMR) and spectrometric (MALDI-TOF-MS) methods. The next stage of the research involved studying the thermogravimetric properties of the borasilsesquioxanes. By analyzing the different stages of decomposition using spectroscopic techniques (NMR, ATR-FTIR, Raman) and microscopic imaging, it was found that the structure of the borasilsesquioxanes changed during the pyrolysis process and polymer compounds were formed.

Organosilicon Compounds in Hot-Melt Adhesive Technologies.

Hot-melt adhesives (HMAs) are thermoplastic materials that can bond various substrates by solidifying rapidly upon cooling from the molten state, and their modification with organosilicon compounds can result in crosslinking behavior, characteristic of gels. Organosilicon compounds are hybrid molecules that have both inorganic and organic components and can enhance the properties and performance of HMAs. The gel aspect of HMA with and without organosilicon modifiers can be considered in organosilicon-modified systems, the modifiers are often either sol-gel condensation products or their mechanism of action on the adherent surface can be considered of sol-gel type. The purpose of this manuscript is to present the current state of the art on the formulation, characterization, and application of HMAs and optimize their performance with organosilicon compounds for application in various industries such as automotive, construction, and photovoltaics. This review covers articles published within the period of 2018-2022. The article is divided into sections, in which information about hot-melt adhesives is described at the beginning. The following part of the presented review focuses on the composition of hot-melt adhesives, which takes into account the use of organosilicon compounds. The last part of this review outlines the future trends in hot-melt adhesives.

Trimming flow, plasticity, and mechanical properties by cubic silsesquioxane chemistry.

In this work, the possibility of managing the rheological and mechanical parameters of composites based on PLA with the use of cubic structures of organofunctional spherosilicates was verified. To accurately observe the effect of various organosilicon modifier substitutions on changes in composites' properties, we synthesized and used monofunctional octasubstituted derivatives as reference systems. The OSS/PLA systems were tested with concentrations of 0.1-2.5% (w/w) using extrusion to obtain a filament with a diameter of 1.75 mm. The printed samples underwent comprehensive tests including microscopic (SEM-EDS, optical microscope), rheological, thermal (TG, DSC, HDT), mechanical (impact and strength) as well as water contact angle tests. The work is interdisciplinary in nature and combines elements of organosilicon synthesis, materials engineering, and materials processing and characterization technology.

The 3D-Printed (FDM/FFF) Biocomposites Based on Polylactide and Carbonate Lake Sediments-Towards a Circular Economy.

In this study, composites containing polylactide and carbonate lake sediment in concentrations of 2.5, 5, 10, and 15% by weight were prepared by a 3D printing method. The material for 3D printing was obtained by directly diluting the masterbatch on an injection moulder to the desired concentrations, and after granulation, it was extruded into a filament. The material prepared thusly was used to print standardised samples for mechanical testing. To compare the mechanical properties of the composites obtained by 3D printing and injection moulding, two sets of tests were performed, i.e., mechanical tests (tensile strength, flexural strength, and impact strength) and hydrophobic-hydrophilic surface character testing. The degree of composite waste in the 3D printing was also calculated. Mechanical and surface tests were performed for both systems conditioned at room temperature and after accelerated ageing in a weathering chamber. The study showed differences in the properties of composites obtained by 3D printing. Sedimentary fillers improved the hydrophobicity of the systems compared with pure PLA, but it was not a linear relationship. The PLA/CLS sedB composite had higher strength parameters, especially after ageing in a weathering chamber. This is due to its composition, in which, in addition to calcite and silica, there are also aluminosilicates, causing a strengthening of the PLA matrix.

Honeycomb Biosilica in Sponges: From Understanding Principles of Unique Hierarchical Organization to Assessing Biomimetic Potential.

Structural bioinspiration in modern material science and biomimetics represents an actual trend that was originally based on the bioarchitectural diversity of invertebrate skeletons, specifically, honeycomb constructs of natural origin, which have been in humanities focus since ancient times. We conducted a study on the principles of bioarchitecture regarding the unique biosilica-based honeycomb-like skeleton of the deep-sea glass sponge Aphrocallistes beatrix. Experimental data show, with compelling evidence, the location of actin filaments within honeycomb-formed hierarchical siliceous walls. Principles of the unique hierarchical organization of such formations are discussed. Inspired by poriferan honeycomb biosilica, we designed diverse models, including 3D printing, using PLA-, resin-, and synthetic-glass-prepared corresponding microtomography-based 3D reconstruction.

Feldspar-Modified Methacrylic Composite for Fabrication of Prosthetic Teeth.

This study was aimed at investigating poly(methyl methacrylate) (PMMA), modified with a silanized feldspar filler at 10 wt.% and 30 wt.%, as a dental material system for the production of prosthetic teeth. Samples of this composite were subjected to a compressive strength test, three-layer methacrylic teeth were fabricated with the said materials, and their connection to a denture plate was examined. The biocompatibility of the materials was assessed via cytotoxicity tests on human gingival fibroblasts (HGFs) and Chinese hamster ovarian cells (CHO-K1). The addition of feldspar significantly improved the material's compressive strength, with neat PMMA reaching 107 MPa, and the addition of 30% feldspar raising it up to 159 MPa. As observed, composite teeth (cervical part made of neat PMMA, dentin with 10 wt.%, and enamel with 30 wt.% of feldspar) had good adhesion to the denture plate. Neither of the tested materials revealed any cytotoxic effects. In the case of hamster fibroblasts, increased cell viability was observed, with only morphological changes being noticed. Samples containing 10% or 30% of inorganic filler were determined to be safe for treated cells. The use of silanized feldspar to fabricate composite teeth increased their hardness, which is of significant clinical importance for the duration of use of non-retained dentures.

Molybdenum Disulphide Modified Polylactide for 3D Printed (FDM/FFF) Filaments.

MoS2 is an additive used to improve the tribological properties of plastics. In this work, it was decided to verify the use of MoS2 as a modifier of the properties of PLA filaments used in the additive FDM/FFF technique. For this purpose, MoS2 was introduced into the PLA matrix at concentrations of 0.025-1.0% by weight. Through extrusion, a fibre with a diameter of 1.75 mm was obtained. 3D printed samples with three different filling patterns were subjected to comprehensive thermal (TG, DSC and HDT), mechanical (impact, bending and strength tests), tribological and physicochemical characteristics. The mechanical properties were determined for two different types of fillings, and samples with the third type of filling were used for tribological tests. Tensile strength has been significantly increased for all samples with longitudinal filling with improvement up to 49%. In terms of tribological properties, higher values of the addition (0.5%) caused a significant increase of up to 457% of the wear indicator. A significant improvement in processing properties in terms of rheology was obtained (416% compared to pure PLA with the addition of 1.0%), which translated into more efficient processing, increased interlayer adhesion and mechanical strength. As a result, the quality of printed objects has been improved. Microscopic analysis was also carried out, which confirmed the good dispersion of the modifier in the polymer matrix (SEM-EDS). Microscopic techniques (MO, SEM) allowed for the characterization of the effect of the additive on changes in the printing process (improvement of interlayer remelting) and to assess impact fractures. In the tribological area, the introduced modification did not bring spectacular effects.

Polyamide 11 Composites Reinforced with Diatomite Biofiller-Mechanical, Rheological and Crystallization Properties.

Amorphic diatomaceous earth is derived from natural sources, and polyamide 11 (PA11) is produced from materials of natural origin. Both of these materials show a low harmfulness to the environment and a reduced carbon footprint. This is why the combination of these two constituents is beneficial not only to improve the physicochemical and mechanical properties of polyamide 11 but also to produce a biocomposite. For the purpose of this paper, the test biocomposite was produced by combining polyamide 11, as well as basic and pre-fractionated diatomaceous earth, which had been subjected to silanization. The produced composites were used to carry out rheological (melt flow rate-MFR), mechanical (tensile strength, bending strength, impact strength), crystallographic (X-ray Diffraction-XRD), thermal and thermo-mechanical (differential scanning calorimetry-DSC, dynamic mechanical thermal analysis-DMTA) analyses, as well as a study of hydrophobic-hydrophilic properties of the material surface (wetting angle) and imaging of the surface of the composites and the fractured specimens. The tests showed that the additive 3-aminopropyltriethoxysilane (APTES) acted as an agent that improved the elasticity of composites and the melt flow rate. In addition, the produced composites showed a hydrophilic surface profile compared to pure polylactide and polyamide 11.

Improving the Dispersibility of TiO2 in the Colloidal System Using Trifunctional Spherosilicates.

Titanium dioxide is a commonly used ingredient in cosmetics acting as a thickening agent and inorganic UV filter. However, TiO2 is difficult to disperse, which causes problems in spreading the formulations. The solution to this problem is to modify the titanium dioxide surface to change its properties by creation of the new type of hybrid inorganic-organic UV filter. Therefore, this study aimed to functionalize titanium dioxide with organosilicon compounds and determine how this modification will affect the dispersibility of TiO2 in the colloidal system and the stability of emulsions. First, the functionalized octaspherosilicates were obtained and characterized. Next, the synthesized compounds were applied as modifiers for titanium dioxide and were analyzed by FT-IR, UV-Vis, and laser diffraction. Furthermore, the hydrophilic-hydrophobic character was assessed by measuring the contact angle. The new materials were introduced into emulsions and the formulations were analyzed in terms of particle size distribution and stability by multiple light scattering. It was found that the modification of titanium dioxide with spherosilicates significantly improved both the stability of emulsion and the dispersibility of novel materials in the colloidal system compared to nonmodified TiO2. The covalent binding of the modifier with the titanium dioxide had an impact on the stability of the emulsion.

Silane-Bearing Borasilsesquioxanes: Synthetic Protocol and Unsuspected Redistribution Reactions.

The presented work is a continuation of research on the reactivity of unsaturated borasilsesquioxanes under the conditions of common organometallic transformations. The catalytic hydrosilylation reaction with silanes, siloxanes and silsesquioxanes in presence of platinum catalyst was explored. The majority of the products were obtained in high yields (>90 %) and their structures were confirmed and characterized by spectroscopy and spectrometry, i. e. NMR and MALDI-TOF-MS. The most significant segment of the work is research on the spontaneous redistribution reaction of the alkoxy group from silane to borane moiety occurring in the obtained products, not being limited to the heterosilsesquioxane chemistry, however. The products were confirmed using GC-MS, ESI-MS methods and B3LYP exchange-correlation, in order to ascertain formation of the silicon-boron hybrid molecule.

Beeswax as a natural alternative to synthetic waxes for fabrication of PLA/diatomaceous earth composites.

In this study, injection moulding was applied to produce biocomposites consisting of polylactide (PLA) and amorphous diatomaceous earth used as a filler at different concentrations. Natural wax and synthetic wax were added to improve processing properties, comparing the resulting biocomposites. The use of natural beeswax makes the composite environmentally friendly. The prepared composites contained 2.5, 5, 10 and 15% w/w filler. The test samples have been injection moulded. Rheological, mechanical, surface and other properties were assessed for the fabricated composites. The testing has shown that the use of wax additives has a significant influence on the mechanical properties (tensile strength, flexural strength, impact strength) and the hydrophilicity/hydrophobicity of composite surfaces. The addition of natural wax, especially at lower concentration, has a positive effect on the rheological properties of composites (melt flow rate, MFR), flexural modulus and impact strength. Different composite parameters are modified by different wax types so both natural and synthetic waxes, can be used interchangeably, depending on the required final material characteristics.

The Influence of Organofunctional Substituents of Spherosilicates on the Functional Properties of PLA/TiO2 Composites Used in 3D Printing (FDM/FFF).

In this study, the influence of TiO2 pigment filler modified with spherosilicate derivatives on the processes and thermomechanical properties of composites based on PLA was investigated. Rheological tests (MFR) were carried out, on the basis of which it was found that the addition of organosilicon compounds has a plasticizing effect on the polymer-filler systems. TGA and DSC analysis were performed. The analysis of the contact angle showed that 1.5% of the additives had an influence on the superhydrophobic properties of TiO2 (above 135°), and a slight improvement of this parameter was also observed for composites containing the modified pigment. Microscopic analysis and mechanical tests (tensile strength, impact strength and flexural strength tests) were carried out as well. It has been observed that the addition of certain derivatives adversely affects the dispersion of the filler, thus a slight improvement in mechanical properties is observed. For modifiers that do not affect filler agglomeration, a plasticizing effect on the composite is observed.

Effect of Wax Additives and Silanization of Diatom Surfaces on Thermomechanical Properties of Polylactide Composites.

In the present study, tests were conducted on high-filled composite samples on a polylactide matrix, modified with diatomaceous earth, three types of silanes, and natural and synthetic wax. The obtained samples were characterized in terms of the effect of modifications on mechanical properties (tensile strength, flexural strength, and impact resistance) or processing properties, e.g., melt flow rate (MFR). The study showed that the modification had a favorable effect on the processing properties of the composites, associated with up to an eight-fold increase in flow rate index compared with the reference sample, especially for samples treated with methyltrimethoxysilane (MTMOS), and up to a ten-fold increase under low shear-rate flow conditions. The effect of the addition of waxes of different origins (synthetic and natural) was also determined, and it was shown that beeswax tended to reduce the flow rate of the composites regardless of the silane used. The addition of synthetic wax to composites increased the tendency to agglomerate diatomaceous earth, while natural wax had a positive effect on filler dispersion.

Aspects and Principles of Material Connections in Restorative Dentistry-A Comprehensive Review.

The combination of two dissimilar materials has always been a serious problem in dentistry. In order to meet this challenge, it is necessary to combine both chemical methods (treatment with silanes, (meth)acrylic functional monomers) and the development of the surface of the joined material in a physical way, e.g., by sandblasting with alumina, alumina with silica, acid etching, the use of lasers and other means. The purpose of this literature review is to present all methods of joining dental composites with other materials such as ceramics, metal, another composite material. This review covers articles published within the period 2012-2022 in journals indexed in the PubMed database, written in English and describing joining different dental materials to each other. All the critical steps of new joint preparation have been addressed, including proper cleaning of the joint surface, the application of appropriate primers capable of forming a chemical bond between ceramics, zirconium oxide or metals and alloys, and finally, the application of new composite materials.

Silsesquioxane-Doped Electrospun Nanofibrillar Membranes for Separation Systems.

In this study, a series of cage siloxanes (CS), e.g., three polyhedral oligomeric silsesquioxanes (SSQs) and one spherosilicate (SS) derivative, were applied as functional additives for the preparation of poly(lactic acid)-based (PLA) nanofibrillar membranes with an electrospinning technique utilizing an efficient spinning wire electrode setup. The impact of the additives' structure, chemistry, and electrospinning parameters on the obtained materials' morphology (scanning electron microscopy) and physicochemical (thermogravimetry, differential scanning calorimetry, contact angle analysis, air flow analysis) properties is discussed. It is presented that applying organosilicon additives may extend the already tuneable properties of the membranes produced by electrospinning performed under different conditions and that they enable to obtain nanofibres of smaller diameter, which in turn increases the membrane porosity. Furthermore, the solvent-assisted electrospinning method allowed for unparalleled mixing of the PLA matrix with the CS additives, as no traces of free additives were visible on the membranes by scanning electron microscopy (SEM) imaging. The resulting membranes can be utilized as filter materials.