Atomic layer deposition and characterization of Bi2Te3 thin films.

Bi2Te3 thin films were deposited by atomic layer deposition (ALD) from BiCl3 and (Et3Si)2Te at 160-300 °C. The process was studied in detail, and growth properties typical of ALD were verified. Films were stoichiometric with low impurity content. The film thickness was easily controlled with the number of deposition cycles. Properties of the ALD Bi2Te3 thin films were found to be comparable to those reported in literature for Bi2Te3 films made by other methods. Films crystallized to a rhombohedral phase, and there was a preferred orientation to the growth. Electrical and thermoelectric properties were also determined to be comparable to literature values.

Atomic layer deposition, characterization, and growth mechanistic studies of TiO2 thin films.

Two heteroleptic titanium precursors were investigated for the atomic layer deposition (ALD) of titanium dioxide using ozone as the oxygen source. The precursors, titanium (N,N'-diisopropylacetamidinate)tris(isopropoxide) (Ti(O(i)Pr)3(N(i)Pr-Me-amd)) and titanium bis(dimethylamide)bis(isopropoxide) (Ti(NMe2)2(O(i)Pr)2), exhibit self-limiting growth behavior up to a maximum temperature of 325 °C. Ti(NMe2)2(O(i)Pr)2 displays an excellent growth rate of 0.9 Å/cycle at 325 °C while the growth rate of Ti(O(i)Pr)3(N(i)Pr-Me-amd) is 0.3 Å/cycle at the same temperature. In the temperature range of 275-325 °C, both precursors deposit titanium dioxide in the anatase phase. In the case of Ti(NMe2)2(O(i)Pr)2, high-temperature X-ray diffraction (HTXRD) studies reveal a thickness-dependent phase change from anatase to rutile at 875-975 °C. X-ray photoelectron spectroscopy (XPS) indicates that the films have high purity and are close to the stoichiometric composition. Reaction mechanisms taking place during the ALD process were studied in situ with quadrupole mass spectrometry (QMS) and quartz crystal microbalance (QCM).

Molecular organization of the tear fluid lipid layer.

The tear fluid protects the corneal epithelium from drying out as well as from invasion by pathogens. It also provides cell nutrients. Similarly to lung surfactant, it is composed of an aqueous phase covered by a lipid layer. Here we describe the molecular organization of the anterior lipid layer of the tear film. Artificial tear fluid lipid layers (ATFLLs) composed of egg yolk phosphatidylcholine (60 mol %), free fatty acids (20 mol %), cholesteryl oleate (10 mol %), and triglycerides (10 mol %) were deposited on the air-water interface and their physico-chemical behavior was compared to egg-yolk phosphatidylcholine monolayers by using Langmuir-film balance techniques, x-ray diffraction, and imaging techniques as well as in silico molecular level simulations. At low surface pressures, ATFLLs were organized at the air-water interface as heterogeneous monomolecular films. Upon compression the ATFLLs collapsed toward the air phase and formed hemispherelike lipid aggregates. This transition was reversible upon relaxation. These results were confirmed by molecular-level simulations of ATFLL, which further provided molecular-scale insight into the molecular distributions inside and dynamics of the tear film. Similar type of behavior is observed in lung surfactant but the folding takes place toward the aqueous phase. The results provide novel information of the function of lipids in the tear fluid.

Liposomes for entrapping local anesthetics: a liposome electrokinetic chromatographic study.

Bupivacaine is a lipophilic, long-acting, amide class local anesthetic commonly used in clinical practice to provide local anesthesia during surgical procedures. Several cases of accidental overdose with cardiac arrest and death have been reported since bupivacaine was introduced to human use. Recent case reports have suggested that Intralipid (Fresenius Kabi) is an effective therapy for cardiac toxicity from high systemic concentrations of, e.g. bupivacaine, even though the mechanism behind the interaction is not fully clear yet. Our long-term aim is to develop a sensitive, efficient, and non-harmful lipid-based formulation to specifically trap harmful substances in vivo. In this study, the in vitro interaction of local anesthetics (bupivacaine, prilocaine, and lidocaine) with Intralipid or lipid vesicles containing phosphatidylglycerol, phosphatidylcholine, cardiolipin, cholesterol, and N-palmitoyl-D-erythro-sphingosine (ceramide) was determined by liposome electrokinetic chromatography. The interactions were evaluated by calculating the retention factors and distribution constants. Atomic force microscopy measurements were carried out to confirm that the interaction mechanism was solely due to interactions between the analytes and the moving pseudostationary phase and not by interactions with a stationary lipid phase adsorbed to the fused-silica wall. The heterogeneity of the liposomes was also studied by atomic force microscopy. The liposome electrokinetic chromatography results demonstrate that there is higher interaction between the drugs and negatively charged liposome dispersion than with the commercial Intralipid dispersion.

Electroactivity and biocompatibility of polypyrrole-hyaluronic acid multi-walled carbon nanotube composite.

Electroactivity of polypyrrole hyaluronic acid, electropolymerized in the presence of oxidized carbon nanotubes (PPyHA-CNT) was studied in situ by electrochemical atomic force microscopy (EC-AFM) in physiological electrolyte solution. In situ Raman spectroscopic and quartz crystal microbalance (QCM) studies were conducted on layers of the polymer grown on AT-cut 5 MHz quartz crystals. Human adipose stem cell (ASC) attachment and viability were studied by Live/Dead staining, and the proliferation was evaluated by WST-1 Cell proliferation assay for polypyrrole samples electropolymerized on titanium. According to cyclic voltammetry, the measured specific capacitance of the material on gold is roughly 20% of the reference polypyrrole dodecylbenzene sulfonate (PPyDBS). Electrochemical-QCM (EC-QCM) analysis of a 210-nm thick film reveals that the material is very soft G' approximately 100 kPa and swells upon reduction. EC-AFM of samples polymerized on microelectrodes show that there are areas of varying electroactivity, especially for samples without a hydrophopic backing PPyDBS layer. AFM line scans show typically 20-25% thickness change during electrochemical reduction. Raman spectroscopic analysis suggests that the material supports noticeable polaron conduction. Biocompatibility study of the PPyHA-CNT on titanium with adipose stem cells showed equal or better cell attachment, viability, and proliferation compared with the reference polylactide.

Atomic layer deposition as pore diameter adjustment tool for nanoporous aluminum oxide injection molding masks.

The wetting properties of polypropylene (PP) surfaces were modified by adjusting the dimensions of the surface nanostructure. The nanostructures were generated by injection molding with nanoporous anodized aluminum oxide (AAO) as the mold insert. Atomic layer deposition (ALD) of molybdenum nitride film was used to control the pore diameters of the AAO inserts. The original 50-nm pore diameter of AAO was adjusted by depositing films of thickness 5, 10, and 15 nm on AAO. Bis(tert-butylimido)-bis(dimethylamido)molybdenum and ammonia were used as precursors in deposition. The resulting pore diameters in the nitride-coated AAO inserts were 40, 30, and 20 nm, respectively. Injection molding of PP was conducted with the coated inserts, as well as with the non-coated insert. Besides the pore diameter, the injection mold temperature was varied with temperatures of 50, 70, and 90 degrees C tested. Water contact angles of PP casts were measured and compared with theoretical contact angles calculated from Wenzel and Cassie-Baxter theories. The highest contact angle, 140 degrees , was observed for PP molded with the AAO mold insert with 30-nm pore diameter. The Cassie-Baxter theory showed better fit than the Wenzel theory to the experimental values. With the optimal AAO mask, the nanofeatures in the molded PP pieces were 100 nm high. In explanation of this finding, it is suggested that some sticking and stretching of the nanofeatures occurs during the molding. Increase in the mold temperature increased the contact angle.

Superhydrophobic polyolefin surfaces: controlled micro- and nanostructures.

Superhydrophobic polyolefin surfaces were prepared by simultaneous micro- and nanostructuring. Electropolished aluminum foil was microstructured with a micro working robot and then anodized in polyprotic acid. The surface microstructure can be tailored by adjusting the settings of the micro working robot and the nanostructure by adjusting the parameters of the anodization procedure. Surface structuring was done by injection molding where a microstructured anodized aluminum oxide mold insert was used to pattern the surfaces. Structuring had a marked effect on the contact angle between the injection-molded polyolefins and water. When the optimized microstructure was covered with nanostructure, the static contact angle between polypropylene and water obtained a value of about 165 degrees and the sliding angle decreased to about 2.5 degrees. The superhydrophobic state was achieved.