Coumarin-Based Photodegradable Hydrogels Enable Two-Photon Subtractive Biofabrication at 300†mm s-1.

Spatiotemporally controlled two-photon photodegradation of hydrogels has gained increasing attention for high-precision subtractive tissue engineering. However, conventional photolabile hydrogels often have poor efficiency upon two-photon excitation in the near-infrared (NIR) region and thus require high laser dosage that may compromise cell activity. As a result, high-speed two-photon hydrogel erosion in the presence of cells remains challenging. Here we introduce the design and synthesis of efficient coumarin-based photodegradable hydrogels to overcome these limitations. A set of photolabile coumarin-functionalized polyethylene glycol linkers are synthesized through a Passerini multicomponent reaction. After mixing these linkers with thiolated hyaluronic acid, semi-synthetic photodegradable hydrogels are formed in situ via Michael addition crosslinking. The efficiency of photodegradation in these hydrogels is significantly higher than that in nitrobenzyl counterparts upon two-photon irradiation at 780 nm. A complex microfluidic network mimicking the bone microarchitecture is successfully fabricated in preformed coumarin hydrogels at high speeds of up to 300 mm s-1 and low laser dosage down to 10 mW. Further, we demonstrate fast two-photon printing of hollow microchannels inside a hydrogel to spatiotemporally direct cell migration in 3D. Collectively, these hydrogels may open new avenues for fast laser-guided tissue fabrication at high spatial resolution.

Guiding bone cell network formation in 3D via photosensitized two-photon ablation.

A long-standing challenge in skeletal tissue engineering is to reconstruct a three-dimensionally (3D) interconnected bone cell network in vitro that mimics the native bone microarchitecture. While conventional hydrogels are extensively used in studying bone cell behavior in vitro, current techniques lack the precision to manipulate the complex pericellular environment found in bone. The goal of this study is to guide single bone cells to form a 3D network in vitro via photosensitized two-photon ablation of microchannels in gelatin methacryloyl (GelMA) hydrogels. A water-soluble two-photon photosensitizer (P2CK) was added to soft GelMA hydrogels to enhance the ablation efficiency. Remarkably, adding 0.5 mM P2CK reduced the energy dosage threshold five-fold compared to untreated controls, enabling more cell-compatible ablation. By employing low-energy ablation (100 J/cm2) with a grid pattern of 1 µm wide and 30 µm deep microchannels, we induced dendritic outgrowth in human mesenchymal stem cells (hMSC). After 7 days, the cells successfully utilized the microchannels and formed a 3D network. Our findings reveal that cellular viability after low-energy ablation was comparable to unablated controls, whereas high-energy ablation (500 J/cm2) resulted in 42 % cell death. Low-energy grid ablation significantly promoted network formation and >40 µm long protrusion outgrowth. While the broad-spectrum matrix metalloproteinase inhibitor (GM6001) reduced cell spreading by inhibiting matrix degradation, cells invaded the microchannel grid with long protrusions. Collectively, these results emphasize the potential of photosensitized two-photon hydrogel ablation as a high-precision tool for laser-guided biofabrication of 3D cellular networks in vitro. STATEMENT OF SIGNIFICANCE: The inaccessible nature of osteocyte networks in bones renders fundamental research on skeletal biology a major challenge. This limit is partly due to the lack of high-resolution tools that can manipulate the pericellular environment in 3D cultures in vitro. To create bone-like cellular networks, we employ a two-photon laser in combination with a two-photon sensitizer to erode microchannels with low laser dosages into GelMA hydrogels. By providing a grid of microchannels, the cells self-organized into a 3D interconnected network within days. Laser-guided formation of 3D networks from single cells at micron-scale resolution is demonstrated for the first time. In future, we envisage in vitro generation of bone cell networks with user-dictated morphologies for both fundamental and translational bone research.

Synergizing Algorithmic Design, Photoclick Chemistry and Multi-Material Volumetric Printing for Accelerating Complex Shape Engineering.

The field of biomedical design and manufacturing has been rapidly evolving, with implants and grafts featuring complex 3D design constraints and materials distributions. By combining a new coding-based design and modeling approach with high-throughput volumetric printing, a new approach is demonstrated to transform the way complex shapes are designed and fabricated for biomedical applications. Here, an algorithmic voxel-based approach is used that can rapidly generate a large design library of porous structures, auxetic meshes and cylinders, or perfusable constructs. By deploying finite cell modeling within the algorithmic design framework, large arrays of selected auxetic designs can be computationally modeled. Finally, the design schemes are used in conjunction with new approaches for multi-material volumetric printing based on thiol-ene photoclick chemistry to rapidly fabricate complex heterogeneous shapes. Collectively, the new design, modeling and fabrication techniques can be used toward a wide spectrum of products such as actuators, biomedical implants and grafts, or tissue and disease models.

Evidence That DDR1 Promotes Oligodendrocyte Differentiation during Development and Myelin Repair after Injury.

Oligodendrocytes generate myelin sheaths vital for the formation, health, and function of the central nervous system. Mounting evidence suggests that receptor tyrosine kinases (RTKs) are crucial for oligodendrocyte differentiation and myelination in the CNS. It was recently reported that discoidin domain receptor 1 (Ddr1), a collagen-activated RTK, is expressed in oligodendrocyte lineage. However, its specific expression stage and functional role in oligodendrocyte development in the CNS remain to be determined. In this study, we report that Ddr1 is selectively upregulated in newly differentiated oligodendrocytes in the early postnatal CNS and regulates oligodendrocyte differentiation and myelination. Ddr1 knock-out mice of both sexes displayed compromised axonal myelination and apparent motor dysfunction. Ddr1 deficiency alerted the ERK pathway, but not the AKT pathway in the CNS. In addition, Ddr1 function is important for myelin repair after lysolecithin-induced demyelination. Taken together, the current study described, for the first time, the role of Ddr1 in myelin development and repair in the CNS, providing a novel molecule target for the treatment of demyelinating diseases.

ADAMTS4 Enhances Oligodendrocyte Differentiation and Remyelination by Cleaving NG2 Proteoglycan and Attenuating PDGFRα Signaling.

Although NG2 is known to be selectively expressed in oligodendrocyte precursor cells (OPCs) for many years, its expressional regulation and functional involvement in oligodendrocyte differentiation have remained elusive. Here, we report that the surface-bound NG2 proteoglycan can physically bind to PDGF-AA and enhances PDGF receptor alpha (PDGFRα) activation of downstream signaling. During differentiation stage, NG2 protein is cleaved by A disintegrin and metalloproteinase with thrombospondin motifs type 4 (Adamts4), which is highly upregulated in differentiating OPCs but gradually downregulated in mature myelinating oligodendrocytes. Genetic ablation of Adamts4 gene impedes NG2 proteolysis, leading to elevated PDGFRα signaling but impaired oligodendrocyte differentiation and axonal myelination in both sexes of mice. Moreover, Adamts4 deficiency also lessens myelin repair in adult brain tissue following Lysophosphatidylcholine-induced demyelination. Thus, Adamts4 could be a potential therapeutic target for enhancing oligodendrocyte differentiation and axonal remyelination in demyelinating diseases.SIGNIFICANCE STATEMENT NG2 is selectively expressed in OPCs and downregulated during differentiation stage. To date, the molecular mechanism underlying the progressive removal of NG2 surface proteoglycan in differentiating OPCs has been unknown. In this study, we demonstrate that ADAMTS4 released by differentiating OPCs cleaves surface NG2 proteoglycan, attenuates PDGFRα signaling, and accelerates oligodendrocyte differentiation. In addition, our study also suggests ADAMTS4 as a potential therapeutic target for promoting myelin recovery in demyelinating diseases.

Tomographic volumetric bioprinting of heterocellular bone-like tissues in seconds.

Tomographic volumetric bioprinting (VBP) has recently emerged as a powerful tool for rapid solidification of cell-laden hydrogel constructs within seconds. However, its practical applications in tissue engineering requires a detailed understanding of how different printing parameters (concentration of resins, laser dose) affect cell activity and tissue formation. Herein, we explore a new application of VBP in bone tissue engineering by merging a soft gelatin methacryloyl (GelMA) bioresin (<5 kPa) with 3D endothelial co-culture to generate heterocellular bone-like constructs with enhanced functionality. To this, a series of bioresins with varying concentrations of GelMA and lithium Phenyl(2,4,6-trimethylbenzoyl)phosphinate (LAP) photoinitiator were formulated and characterized in terms of photo-reactivity, printability and cell-compatibility. A bioresin with 5% GelMA and 0.05% LAP was identified as the optimal formulation for VBP of complex perfusable constructs within 30 s at high cell viability (>90%). The fidelity was validated by micro-computed tomography and confocal microscopy. Compared to 10% GelMA, this bioresin provided a softer and more permissive environment for osteogenic differentiation of human mesenchymal stem cells (hMSCs). The expression of osteoblastic markers (collagen-I, ALP, osteocalcin) and osteocytic markers (podoplanin, Dmp1) was monitored for 42 days. After 21 days, early osteocytic markers were significantly increased in 3D co-cultures of hMSCs with human umbilical vein endothelial cells (HUVECs). Additionally, we demonstrate VBP of a perfusable, pre-vascularized model where HUVECs self-organized into an endothelium-lined channel. Altogether, this work leverages the benefits of VBP and 3D co-culture, offering a promising platform for fast scaled biofabrication of 3D bone-like tissues with unprecedented functionality. STATEMENT OF SIGNIFICANCE: This study explores new strategies for ultrafast bio-manufacturing of bone tissue models by leveraging the advantages of tomographic volumetric bioprinting (VBP) and endothelial co-culture. After screening the properties of a series of photocurable gelatin methacryloyl (GelMA) bioresins, a formulation with 5% GelMA was identified with optimal printability and permissiveness for osteogenic differentiation of human mesenchymal stem cells (hMSC). We then established 3D endothelial co-cultures to test if the heterocellular interactions may enhance the osteogenic differentiation in the printed environments. This hypothesis was evidenced by increased gene expression of early osteocytic markers in 3D co-cultures after 21 days. Finally, VBP of a perfusable cell-laden tissue construct is demonstrated for future applications in vascularized tissue engineering.

Antimicrobial Thiol-ene-acrylate Photosensitive Resins for DLP 3D Printing.

Designing digital light processing (DLP) 3D printable photosensitive resins with antibacterial properties is especially vital because of their potential applications in various biomedical fields. In this contribution, a thiol-ene-acrylate ternary system with reduced volume shrinkage and fast photopolymerization rate was chosen as the antibacterial 3D printing matrix resin. Two quaternary ammonium salt-type antibacterial agents (QAC and SH-QAC) with different molecular weight were designed and prepared, which can participate in the curing of matrix resin to achieve contact antibacterial effect. The effects of antibacterial agent content on the photopolymerization kinetics and on thermal and mechanical properties were discussed in detail. When the amount of added QAC is 4wt%, the antibacterial rate is almost 100% for Escherichia coli and Staphylococcus aureus, and when the amount of SH-QAC is 10wt%, the antibacterial rate against S. aureus is also essentially 100%. Both antibacterial photosensitive resins have been successfully applied in DLP technology to fabricate tooth model with high precision.